MEKEDE Car Multimedia System for Volkswagen Tiguan 2 Mk 2016-2019

Contents

MEKEDE Car Multimedia System User Manual

Model: Car Multimedia System for Volkswagen Tiguan 2 Mk 2016-2019

1. Introduction and Safety Measures

Thank you for choosing the MEKEDE Car Multimedia System. To ensure safe and effective use, please read these instructions carefully.

Safety Precautions:

  • Do not watch videos or use other visual accessories while driving. Active use of the system during driving is not recommended as it can reduce attention and may result in traffic violations or accidents.
  • This unit is designed for use in cars with a 12V power supply and a negative ground. Do not install the system in vehicles with a 24V on-board voltage, as this may cause damage.
  • Use a specialized cleaning device to maintain the screen.
  • To prevent overheating, avoid direct exposure to sunlight and do not install near heating systems. The optimal operating temperature is between 0°C and 35°C. If the vehicle interior temperature is too high, cool it before turning on the system. Avoid operating the unit at very low temperatures; wait until the interior and vehicle temperatures normalize.
  • Only use the provided fasteners (screws, mounting frames, etc.) for installation. Using other fasteners may damage the system and is not covered by the warranty.
  • Installation and connection of the device should be performed by a qualified specialist or trained service staff.
  • Do not reset to factory settings unless absolutely necessary, as this may result in loss of settings and incorrect operation.
  • Violation of these instructions or improper use may cause system malfunction, voiding the warranty.

2. Package Contents

The package includes the following items:

Package Contents: Machine, Power Cable+Canbus Box, RCA Cable, USB Cable, Reversing Camera, GPS Antenna

Image: Package Contents including the main unit, power cables, RCA cables, USB cables, reversing camera, and GPS antenna.

  • Main Unit (Machine)
  • Power Cable + Canbus Box
  • RCA Cable
  • USB Cable (x2 or x3 depending on model)
  • Reversing Camera (optional, may be sold separately)
  • GPS Antenna
  • 4G Antenna (optional)
  • Microphone (built-in)

3. Installation

Connection Diagram:

Refer to the diagram below for proper wiring connections. Ensure all cables are securely connected before powering on the device.

Detailed wiring diagram for the car multimedia system, showing connections for power, speakers, steering wheel control, reverse, and antennas.

Image: Detailed wiring diagram for the car multimedia system.

Rear Camera Connection:

Without CANBus Box:

  • Connect the reversing mode control wire to A5.
  • Connect the camera power supply (12V) to the car's reverse light 12V power supply.
  • Connect the camera ground (GND) to the car's ground.

With CANBus Box:

  • If a CANBus box is used and the reverse control line (A3 area) is connected to the CANBus box, the yellow RCA line connection may not be needed.
  • Connect ACC to A3 ACC.
  • Connect the two red wires of the camera power supply together; do not connect with other wires.
  • Connect the camera ground (GND) to the car's ground.

CANBus Box Setup:

If your car's original functions (e.g., steering wheel control) are not working, the CANBus type may need to be set. Check your CANBus photo and select the corresponding type in the system settings.

Setup Steps:

  1. Connect the CANBus box as shown in the picture.
  2. Go to Settings > Car Settings > Factory (Password: 8888).
  3. Select the appropriate Car Model and CANBox type.

4. Operating Instructions

Front Panel Controls:

The front panel features several buttons for quick access to functions:

  1. Microphone
  2. Emergency reassembly of equipment (Reset button)
  3. Input/output switch / Live switch / Sound switch
  4. Return to main menu
  5. Switching back to the previous menu
  6. Increase volume
  7. Lower the volume

Turning On/Off the Device:

After switching off the ignition and starting the engine, the multimedia system automatically switches on. The display shows the initial screen. The unit activates automatically after the engine is switched off.

Touch Screen Operation:

The unit features an interactive touchscreen display. Ensure the protective plastic membrane is removed before first use. Otherwise, the touch screen may not function properly.

  • Touch: Tap an item to start a plugin (signal source) or select a menu item.
  • Double Tap: A quick double touch allows you to resize images.
  • Touch & Hold: Press and hold an item for 2 seconds to trigger additional actions.
  • Dragging: Touch and hold a selected item, then drag it to a new position.
  • Moving: Rotate the screen with your finger and keep your finger touched, moving it in the desired direction.
  • Scroll through: Move your finger on the screen in the desired direction and let go. Rotation can be stopped by touching the screen again.

Attention: Do not use metal or sharply pointed objects to control the screen. Do not apply excessive force.

Main Menu Customization:

You can customize the position of icons and edit applications in the quick menu bar for easy operation. You can also change the wallpaper of the main menu interface.

Various main menu UI options and customization examples.

Image: Examples of different main menu interfaces.

Change Wallpaper: You can set a picture or photo as a background. Choose from pre-installed live wallpapers, static wallpapers, or images/photos stored on a USB memory device or SD card.

FM/AM Radio:

To access the radio, tap the 'Radio' icon on the main menu. You can automatically search for stations or manually tune to a specific frequency.

FM RDS Radio interface showing frequency tuning and station presets.

Image: FM RDS Radio interface.

  • Main Menu: Access radio functions.
  • FM Switching Group: Switch between FM bands.
  • LOC/DX Mode: 'LOC' receives strong signals only; 'DX' receives all stations in the current range.
  • MONO Mode: Enable mono audio.
  • Automatic Scanning: Scan for available stations.
  • Save Station: Save current station to presets.
  • Additional Adjustments: Fine-tune settings.
  • List of Saved Stations: View and select saved stations.

DSP Processor/Equalizer:

Access the equalizer (EQ) by pressing the 'Equalizer' icon. The built-in DSP chip allows for advanced sound settings.

  • Equalizer Mode: Adjust sound using various frequency settings (Rock, Soft, Jazz, Pop, Classical, Hall). Reset to default with 'Standard' button.
  • Automatic Volume Mode: Choose recommended settings for listener position (Driver, Passenger, Rear, Center) or adjust independently.
  • Balance Mode: Adjust speaker volume ratios for comfortable sound. Supports parametric bass tuning.
  • Bass Enhancement: Adjust high and low frequency tones, boost factor.
  • Bass Filter: Set desired frequency for each speaker.

Music/Video Playback:

Connect a USB storage device or insert an SD memory card. Tap 'Music' for audio playback or 'Video' for video playback.

Dual USB support for playing music, movies, and photos.

Image: Dual USB support for media playback.

1080P video playback on the car stereo screen.

Image: 1080P video playback.

Attention: For safety, video playback is restricted while the car is in motion. To view video, stop in a safe place and apply the handbrake.

Bluetooth (BT) Function:

Tap the 'BT' icon in the main menu to access the hands-free interface. Enable Bluetooth on your phone and search for new devices. Pair your phone with the system (PIN: 0000) to enable hands-free calling and music streaming.

Bluetooth interface showing dial pad, contacts, and music playback.

Image: Bluetooth interface with dial pad and music controls.

  • Call Log: View outgoing, incoming, and missed calls.
  • Dialing Interface: Make calls directly from the unit.
  • Telephone Book: Synchronize your phone book to the device.
  • BT Music: Stream music from your mobile phone.
  • Check Connection: Verify Bluetooth connection status.
  • BT Settings: Configure Bluetooth options.

Car Link allows you to use your iPhone (Wireless CarPlay) or Android phone (Wired Android Auto) safely while driving. It enables navigation, calls, messages, and music playback.

CarPlay and Android Auto connection steps.

Image: Wireless CarPlay (iOS) and Wired Android Auto (Android) connection steps.

Wireless CarPlay (iOS System) Connection Steps:

  1. Connect your iPhone via Bluetooth.
  2. Tap on 'Car Link'. Your phone will ask for authorization; authorize and wait for connection.

Wired Android Auto (Android System) Connection Steps:

  1. Connect your mobile phone and car multimedia player with a USB cable.
  2. Tap on 'Car Link'. Your phone will ask for authorization; authorize and wait for connection.

Split Screen:

The device supports split-screen mode, allowing you to display two applications simultaneously, such as navigation and music. To exit, drag the icon between the two screens to the right.

GPS Navigation:

The system features a built-in global positioning system with omni-directional map display, real-time traffic conditions, and accurate positioning.

GPS Navigation interface showing a map with real-time traffic information.

Image: GPS Navigation interface.

Supported navigation apps include Navitel, IGO, Yandex, and Google.

4G LTE:

With 4G LTE connectivity, you can watch live video, listen to music online, play games, and browse the internet. Insert a 4G SIM card into the designated slot.

Language Settings:

To change the system language, go to Settings > Language & Input. Select your preferred language and move it to the first position in the list.

Launcher App Setting:

The device supports multicolor illumination and can be customized. Select the light you want or set it to automatic color change.

5. Optional Features (Additional Accessories)

The following features require additional accessories, which may be sold separately.

DAB+ (Digital Audio Broadcasting):

Enhances sound quality and signal strength for radio reception in EU countries.

OBD II (On-Board Diagnostics):

With an OBDII adapter, you can monitor real-time vehicle data and retrieve fault codes from the car's computer.

OBD II interface showing engine management diagnostics and tools.

Image: OBD II interface displaying vehicle diagnostics.

TPMS (Tire Pressure Monitoring System):

After correct installation, TPMS sensors automatically monitor tire pressure and temperature, transmitting real-time statistics to the receiver.

TPMS interface showing tire pressure and temperature readings.

Image: TPMS interface displaying tire data.

Comparison of external and built-in TPMS sensors.

Image: External vs. Built-in TPMS options.

AV Output:

The video output allows rear passengers to watch HD video and audio through a video cable connected to headrest displays.

360° Camera:

Requires a built-in 360° camera chip on the motherboard. Must be ordered with the car radio.

ADAS DVR (Advanced Driver-Assistance Systems Digital Video Recorder):

Provides anti-collision warnings, front vehicle distance prediction, and lane departure warnings for safer driving.

ADAS DVR interface showing anti-collision and lane departure warnings.

Image: ADAS DVR features for driving safety.

AHD HD Reversing Video:

Provides clearer rear-view video compared to conventional cameras, with automatic activation upon reversing.

AHD Reversing Video display showing a clear rear-view camera feed.

Image: AHD Reversing Video display.

6. Specifications

Below are the technical specifications for the MEKEDE Car Multimedia System:

Car multimedia player parameter table comparing 1GB+32GB and 2GB+32GB models.

Image: Comparison of car multimedia player parameters.

AttributeValue
Mounting Size9"/10"
Screen Resolution1024x600 IPS
Display Size9" or 10"
CPUUIS7862 1.8GHz 8-core (2 cores ARM Cortex A75 + 6 cores ARM Cortex A55)
RAM2GB/3GB/4GB/6GB/8GB DDR3
ROM32GB/64GB/128GB
Operating SystemAndroid 11
Maximum Output Power4 x 45 W
Sound AmplifierTDA 7388/Toshiba 001 (M200S M300S), TDA7851/7850/7838 (M400S M500S M600S M700S)
Chip FM TunerNXP TEF6686
Equalizer FeaturesLow Pass Filter, Tone Compensation, Balance Mode, Surround Sound Mode, Extended Equalizer settings (32 bands)
CarPlay / Android AutoSupported (add-on Car Link)
Video FormatRMVB, MKV, MOV, WMV, AVI, MPG, TS, H.264 codec and others.
Audio FormatMP3, WMA, WAV, OGG, FLAC
GPSBuilt-in receiver with external antenna
Software for NavigationSupport
Wi-FiSupport
360° CameraSupport
BTA2DP and BT address book transfer
Steering Wheel ControlSupport
ADAS DVRActivation in the settings menu
AHD HD ReversingAutomatic activation of video input
4G Internet / 4G LTESupport
DSPSupport
Start16 c~ 20 c
Voltage during OperationDC12V
Voltage at Operating Range9V~16V
Electric Current15A
Operating Temperature-20°C - +70°C
Main Menu LanguageSupport for multiple national languages
Item Weight1.5kg
Package Weight1.715kg
Package Dimensions33cm x 28cm x 13cm

7. Troubleshooting

If you encounter any issues, try disconnecting and reconnecting your device, or press the Reset button. If the problem persists, refer to the table below for common malfunctions and solutions.

SymptomProbable CauseSolution
Device does not power on.Ignition key not in "On" position.Turn the key to the "On" position.
Device does not power on.Overheated fuses (15A).Check the device's circuit breaker. If not working, replace with a new one of the same nominal size.
Device does not power on.Incorrect connection of electrical supply wires (black and yellow).Check the electrical supply connections.
Phonebook contacts are not transferred via Bluetooth.No rights on the phone.After connecting the phone to the device, go to the BT settings on the phone and authorize the transfer of the phone book.

8. User Tips

  • Compatibility with Existing Car Features: If your car has ambient lighting or other integrated features, ensure to check the compatibility of the car multimedia system with your vehicle's CANBus settings during installation. Proper CANBus configuration is crucial for retaining original car functionalities.
  • Firmware Updates: MEKEDE provides free updates for Firmware, Software, UI, and GPS Navigation maps. Regularly check for and install updates to ensure optimal performance and access to new features.
  • Troubleshooting Connectivity: If you experience issues with Bluetooth or CarPlay/Android Auto, first ensure your phone's Bluetooth is on and discoverable, and that you have granted all necessary permissions for the connection. For wired connections, try a different USB cable.

9. Warranty and Support

Warranty Information:

All MEKEDE products undergo strict quality tests before shipment. The product comes with a 1-year warranty period from the date of receipt. If you provide a 5-star review and share installation photos, the warranty can be extended to 2 years.

For any issues within 365 days of receipt, you may be eligible for free return and refund within 15 days, or a direct replacement of the new machine. Please contact customer support first to communicate any issues.

Additional Resources:

For more detailed instructions, diagrams, and troubleshooting, please refer to the full user manual (PDF) available at: MEKEDE Car Multimedia System User Manual (PDF).

For further assistance, please contact MEKEDE Global Store customer support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.