WINXU Universal Controller S810 LED Display Panel

Contents

WINXU E-Bike Brushless Motor Controller and S810 LED Display Panel User Manual

Model: Universal Controller S810 LED Display Panel

Brand: WINXU

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your WINXU E-Bike Brushless Motor Drive Universal Controller and S810 LED Display Panel. This kit is designed for electric bicycle and scooter repair and conversion, offering versatile power and voltage options.

WINXU Brushless Motor Controller and S810 LED Display Panel
Figure 1: WINXU Brushless Motor Controller and S810 LED Display Panel

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Before installing the controller, always disconnect the battery power supply. Do not work with the power on, as it may easily damage the equipment.
  • Ensure all connections are secure and correct. Incorrect wiring, especially of the battery, can lead to short circuits, overheating, and damage to the controller.
  • Always connect the battery as the last step and double-check for reverse polarity connection.

3. Specifications

The WINXU Brushless Motor Controller and S810 LED Display Panel are available in various configurations to suit different e-bike and scooter setups.

Attribute Value
Type Controller
Input Voltage 24V / 36V / 48V
Power 250W / 350W / 500W
Current 13A (250W) / 15A (350W) / 22A (500W)
Motor Type Brushless motor
Motor Phase Angle 60° / 120°
LED Display Voltage 24V / 36V / 48V (LED only supports single voltage)
Controller Dimensions (250W/350W) 140mm (5.5 inch) x 95mm (3.74 inch) x 30mm (1.18 inch)
Controller Dimensions (500W) 140mm (5.5 inch) x 130mm (5.11 inch) x 30mm (1.18 inch)
Controller size comparison for 250W, 350W, and 500W models
Figure 2: Controller Size Comparison (250/350W vs 500W)

4. Installation Instructions

4.1 Pre-use Preparation

Before installing the controller, ensure the battery power supply is disconnected. Working with power on can damage the equipment.

4.2 Reading the Product Wiring Diagram

Before starting the installation, carefully review the wiring diagram and understand the function of each connector.

Wiring diagram for 250W Brushless Controller
Figure 3: 250W Brushless Controller Wiring Diagram

4.3 Connector Function Introduction and Installation Steps

  1. Motor Phase Wire: Connect the three thick wires (yellow, green, blue) from your motor to the corresponding phase wires on the controller. Ensure a secure connection as these handle high current.
  2. Motor Hall Sensor: This controller uses a 6-wire Hall sensor. Connect the Hall sensor wires: red, yellow, and blue are Hall signal wires; red and black are working voltage cables; white is the motor speed signal cable. If your motor has a 5-wire Hall sensor, ignore the white speed signal cable; the controller will automatically detect the speed signal.
  3. LCD Display (S810): This 5-pin connector uses a UART protocol. Red and black are for operating voltage, blue is for controller power control, green is RX, and yellow is TX.
  4. Power Lock: If your e-bike has a key lock, connect its switch to this connector. If not, this connector can be ignored.
  5. Throttle: Connect a Hall throttle (thumb or twist type). It receives a signal voltage of 1.1-4.2V. Red and black are operating voltage, and white is the Hall signal.
  6. PAS Sensor: This controller supports magnetic pulse type universal PAS sensors. Red and black are power voltage wires, and blue is the pulse signal cable.
  7. EABS (Electronic Automatic Braking System): If your scooter uses an EABS type brake, connect it to this connector. EABS brakes are Hall brake systems. Do not use this connector for low-level brakes.
  8. Low-Level Brake: This is a power-off braking system. The black cable is negative, and the white cable is the brake signal. Connect low-level brakes with 2 cables correctly.
  9. Light Power: This connector outputs battery voltage to power accessories like headlights, brake lights, horns, and USB chargers. Yellow is positive, black is negative.
  10. Battery: Connect the battery last. Ensure positive and negative terminals are connected correctly. Incorrect connection can cause short circuits, overheating, and damage. Double-check all connections before connecting the battery.
  11. Automatic Detection (Self-Learning Cable): This connector is crucial for motor matching. After initial installation, turn on the device, lift the motor hub, and plug in this connector. The motor will start driving. If the motor drives in the wrong direction, disconnect and reconnect the self-learning cable to reverse direction. Once the motor drives correctly without vibration, disconnect the self-learning cable.
Detailed view of controller connections and casing
Figure 4: Detailed Controller Connections

5. Operating Instructions

5.1 S810 LED Operator Panel Functions

The S810 LED display panel provides essential control and information for your e-bike or scooter.

S810 LED Operator Panel Detail with button functions
Figure 5: S810 LED Operator Panel Detail
  • On/Off: Power button to turn the system on or off.
  • Light Switch: Activates or deactivates the headlight.
  • 6km/h Walk Assist: Engages a low-speed assist mode for walking alongside the bike.
  • Speed Gear (PAS Gear Support): Adjusts the level of pedal assist.
  • 3 LED Battery Capacity Display: Indicates the remaining battery charge.

5.2 Initial Setup and E07 Display

After the controller is first installed, it may display an E07 error code because motor matching and parameter detection have not been completed. To resolve this:

  1. Use the self-learning cable (Automatic Detection) as described in the installation section to complete motor matching.
  2. Once motor matching is complete, use the throttle and high-speed gear to drive the motor at high speed.
  3. The controller will detect motor parameters and status. If no fault is detected during high-speed driving, the E07 error code will automatically clear.
  4. If E07 still displays, it indicates insufficient driving speed or a fault with the motor or motor Hall sensor. Please check these components.

6. Troubleshooting: LCD Error Code Explanation

The S810 LED display panel may show error codes to indicate specific issues. Refer to the table below for explanations:

Error Code Description
E02 Brake fault
E03 PAS sensor fault
E04 6KM/H cruise mode fault
E05 Real-time cruise fault
E06 Battery undervoltage
E07 Motor failure
E08 Throttle fault
E09 Controller failure
E10 Communication signal reception failure
E11 Communication signal transmission fault
E12 BMS communication fault
E13 Headlight fault

7. Maintenance & Storage

7.1 Cleaning

Turn off the device before cleaning. Use a soft, lint-free cloth to wipe the surfaces. Avoid using harsh chemicals or abrasive materials.

7.2 Storage

Store the controller and display in a dry place at room temperature (15°C - 35°C).

7.3 Long-term Storage

If the device will not be used for an extended period, charge the battery to 50% every 3 months to maintain battery health.

8. User Tips

  • This is a universal controller. It comes with a learning wire and is compatible with many brushless motors on the market.
  • The controller can work without Hall sensors.
  • For PAS (Pedal Assist System), it is recommended to use dual Hall PAS sensors.
  • For the throttle, use a 5V Hall throttle for optimal performance.
  • Consider watching the Kit Installation Sample Video for visual guidance during setup.

Video 1: Kit Installation Sample Video. This video provides a visual guide for the installation process.

9. Disposal & Recycling

This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

10. Warranty & Support

For technical support, warranty claims, or any inquiries regarding your WINXU product, please contact the manufacturer or their authorized representative using the details below. You may also refer to the official User Manual (PDF) for additional information.

Manufacturer Information:

  • Name: ShenZhen Winxu Technology Co., Ltd
  • Address: No.118, Building B, Yongxing Office Building, No. 68, Tianyun Road, Songgang Street, Baoan District, Shenzhen, China
  • E-mail: Winxutech@163.com
  • Tel: +86-15814065441

EU Authorized Representative:

  • Name: Vermilion Bird OU
  • Address: Tartu mnt 67/1-13b, Kesklinna linnaosa, 10115 Tallinn Harju maakond, Estonia
  • E-mail: vermilionbird.eu@outlook.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.