1. Introduction and Overview
Thank you for choosing the Leclstar 80W 6500K LED Garage Light. This high-performance lighting solution is designed to provide superior illumination for a variety of spaces, including garages, workshops, basements, and attics. Featuring a deformable design with 10 adjustable LED panels, it offers 360° lighting coverage and significant energy savings. This manual provides essential information for safe installation, operation, and maintenance of your new LED garage light.
Note on Models:
This manual primarily describes the 80W LED Garage Light with 10 adjustable panels. Please be aware that other configurations, such as 3-panel (80W) or higher wattage (e.g., 150W, 180W) models with different panel counts (e.g., 10+1, 12, 13 panels), may also be available. Specifications may vary slightly between models.
2. Safety Information
- WARNING: Always turn off the power supply at the circuit breaker before installing, removing, or performing any maintenance on the light fixture.
- Ensure the light is securely screwed into the E26/E27 socket to prevent accidental detachment.
- When the adjustable garage lights are operating, the panels will dissipate heat. Avoid touching the panels directly with bare hands to prevent burns.
- Do not look directly into the light when it is on, as the intense brightness can cause eye strain or damage.
- This product is designed for indoor use in dry environments. Do not expose to water or high humidity.
- Keep out of reach of children.
3. Package Contents
Please check the package for the following items:
- 1 x Leclstar LED Garage Light (80W, 10-panel configuration)
- 1 x Instruction Manual (this document)
4. Specifications
| Attribute | Value |
|---|---|
| Wattage | 80W (for 10-panel model) |
| Brightness | 8000 Lumens (for 80W model) |
| Color Temperature | 6500K Daylight |
| Color Rendering Index (CRI) | 80+ |
| Voltage Range | AC85-265V |
| Lifespan | 50,000+ hours |
| Adjustable Panel Angle | 0°-90° |
| Lighting Coverage Area | 360° |
| Socket Type | E26/E27 Standard Screw Socket |
| Body Material | ABS with Aluminum Heatsink |
| Features | Deformable design, Energy-saving, Non-flickering, No radiation, Excellent heat dissipation |
5. Setup and Installation
The Leclstar LED Garage Light is designed for easy, tool-free installation, similar to screwing in a standard light bulb.
- Prepare the Socket: Ensure the power supply to the E26/E27 socket is completely turned off at the circuit breaker before beginning installation.
- Screw in the Light: Carefully screw the garage light clockwise into the E26/E27 socket base until it is firmly seated. Do not overtighten.
- Secure the Light: Ensure the light is tightened to secure it inside the socket.
- Adjust Panels: Once securely installed, adjust the LED panels to your desired angle (0°-90°) to direct light where needed.
- Restore Power: Turn on the power supply at the circuit breaker.
- Activate Light: Flip the wall switch to turn on the light.
6. Operating Instructions
- Turning On/Off: Use your standard wall light switch to turn the garage light on or off.
- Adjusting Panels: The LED panels are designed to be deformable. Gently adjust each panel to achieve the desired lighting angle and coverage for your space. The panels can be adjusted from 0° to 90°.
7. User Tips
No specific user tips were provided for this product. However, general tips for LED garage lights include:
- For optimal lighting, experiment with different panel angles to eliminate shadows in your workspace.
- Consider the height of your ceiling when adjusting panels to maximize light spread.
- Regularly clean the panels to maintain brightness and efficiency.
8. Maintenance
- Cleaning: Ensure the light is turned off and cooled down before cleaning. Use a soft, dry cloth to wipe the panels and housing. Do not use abrasive cleaners or solvents.
- Heat Dissipation: The light is designed with an aluminum heatsink for excellent heat dissipation. Ensure there is adequate airflow around the fixture and do not obstruct the panels or vents.
9. Troubleshooting
- Light does not turn on:
- Check if the power supply to the socket is active.
- Ensure the light is securely screwed into the E26/E27 socket.
- Verify that the wall switch is in the 'ON' position.
- Light flickers:
- Ensure the light is firmly screwed into the socket.
- Check for stable power supply to the fixture.
- Reduced brightness:
- Clean the LED panels to remove any dust or debris.
- Ensure the panels are adjusted to an optimal angle for light distribution.
If you experience persistent issues not covered here, please contact customer support.
10. Warranty and Support
This product comes with a 1-year warranty from the date of purchase, covering manufacturing defects under normal use. Please retain your proof of purchase for warranty claims.
For technical support, warranty inquiries, or any questions regarding your Leclstar LED Garage Light, please contact the seller or manufacturer directly through your purchase platform.
