PowMr HHJ-60A

Contents

PowMr MPPT 60A Solar Charge Controller User Manual

Model: HHJ-60A

1. Important Safety Instructions

WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.

CAUTION: Indicates a critical procedure for safe and proper operation of the controller.

NOTE: Indicates a procedure or function that is important to the safe and proper operation of the controller.

General Safety Information

  • Read all instructions and cautions in the manual before beginning installation.
  • There are no serviceable parts for this controller. DO NOT disassemble or attempt to repair.
  • DO NOT allow water to enter the controller.
  • Make sure all connections going into and from the controller are tight.

Charge Controller Safety

  • NEVER connect the solar panel array to the controller without a battery. Battery must be connected first.
  • Ensure input voltage does not exceed 190 VDC to prevent permanent damage. Use the Open Circuit Voltage (Voc) to make sure the voltage does not exceed this value when connecting panels together.

Battery Safety

  • Use only sealed lead-acid, flooded, gel, or lithium batteries which must be deep cycle.
  • Explosive battery gases may be present while charging. Be certain there is enough ventilation to release the gases.
  • Be careful when working with large lead-acid batteries. Wear eye protection and have fresh water available in case there is contact with battery acid.
  • Carefully read battery manuals before operation.
  • Do NOT let the positive (+) and negative (-) terminals of the battery touch each other.
  • Recycle battery when it is replaced.
  • Over-charging and excessive gas precipitation may damage battery plates and activate material shedding. Too high or too long an equalizing charge may cause damage. Review specific requirements of the battery used.
  • Equalization is carried out only for non-sealed / vented / flooded / wet cell lead-acid batteries.
  • Do NOT equalize VRLA type AGM / Gel / Lithium cell batteries UNLESS permitted by battery manufacturer.

WARNING:

  • Connect battery terminals to the charge controller BEFORE connecting the solar panel(s) to the charge controller. NEVER connect solar panels to charge controller until the battery is connected.
  • Do NOT connect any inverters or battery charger into the load terminal of the charge controller.
  • Once equalization is active in battery charging, it will not exit this stage unless there is adequate charging current from the solar panel. There should be NO load on the batteries when in equalization charging stage.

2. Setup and Installation

The PowMr MPPT 60A Solar Charge Controller (Model HHJ-60A) is designed for efficient solar power management. It features 100% MPPT technology, a high-performance DSP controller, and automatic voltage detection for 12V/24V/36V/48V battery banks. It supports various battery types including sealed lead-acid, vented gel, and lithium batteries.

Video: Overview of the PowMr MPPT 60A Solar Charge Controller, highlighting its features and applications.

Dimensions

The controller measures 214mm x 115mm x 50mm (8.43in x 4.53in x 1.97in).

Dimensions and internal components of the PowMr MPPT 60A Solar Charge Controller

Image: Physical dimensions of the controller and a view of its internal components, including the copper coil transformer and capacitance.

Installation Steps

CAUTION: Use only the provided screws. Using other screws may damage the internal PCB. Apply proper torque to avoid damage.

  1. Connect the batteries: Connect the battery connection cable with the correct polarity to the middle pair of terminals on the solar charge controller (marked with the battery symbol). If the system is 12V, ensure your battery voltage is above 12V for the controller to boot up.
  2. Connect the solar panel: Ensure the PV modules are protected from incident light. Do not exceed the maximum permissible input current. Connect the PV modules connection cable to the correct polarity of the left pair of terminals on the solar charge controller (marked with the PV modules symbol).
  3. Connect loads: Connect the load cable to the correct polarity of the right pair of terminals on the solar charge controller (marked with the lamp symbol). To avoid voltage on the wires, connect the wire to the load before connecting to the controller.
  4. Final check: Tighten all cables connected to the controller and remove all debris around the controller, leaving a space of approximately 5.91 inches for ventilation.

NOTE: When the reading data of PV or battery is constantly changing, the controller is finding the Maximum Power Point (MPP). This is normal. If it persists, check your PV input power or voltage.

Air Circuit Breaker Installation

It is strongly recommended to connect a fuse directly to the battery to protect against short circuits at the battery wiring. Solar PV modules generate current whenever light strikes them. Protect solar modules from incident light during installation. Never touch uninsulated cable ends, use only insulated tools, and ensure the wire diameter is in accordance with expected currents.

Air Circuit Breaker and Wires Requirement

ModelsCopper wiresAir circuit breakers
HHJ-60A6mm²x2PCS100A

Reminder: It’s better to connect two wires to two PV+ and another two wires to two PV-. For BAT+ and BAT-, it’s the same way to connect wires.

Wiring diagram for PowMr MPPT Solar Charge Controller showing connections for PV, Battery, and DC Load

Image: Wiring diagram illustrating connections for solar panels, battery, and DC load to the MPPT solar charge controller. Also shows maximum PV input power for different system voltages.

Connection Sequence:

  1. Install air circuit breaker between controller and batteries. Turn off the circuit breaker, then connect batteries to controller with correct polarity.
  2. Install air circuit breaker between controller and PV modules. Turn off the circuit breaker, and ensure the PV polarity is correct, then connect wires between PV modules and controller.
  3. Turn on the air circuit breaker between controller and batteries.
  4. Turn on the air circuit breaker between controller and PV modules.
  5. The controller goes into self-test mode. Its LCD displays parameters if all is correct. The RUN lamp (under the fan inside the casing) will flash every one second. If the controller is unresponsive, please read the full manual again or contact support.

3. Operating Instructions

LCD Display

The LCD screen provides real-time information about the system status. The main interface displays PV voltage/output power, battery voltage/charging current, working mode/temperature, and fault codes. Sub-interfaces show load timer, floating voltage, absorption voltage, battery type, calibration voltage, and under-voltage disconnection voltage.

LCD display and sub-interfaces of the PowMr MPPT 60A Solar Charge Controller

Image: Detailed view of the controller's LCD screen, showing the main display and various sub-interface parameters like load timer, floating voltage, and battery type settings.

Working Modes

  • 3.0 Night mode: No charging.
  • 4.0 MPPT mode: Maximum Power Point Tracking.
  • 7.0 Absorption mode: Battery charging stage.
  • 8.0 Floating mode: Battery charging stage.

Manual Settings

Reminder: The controller will work fine under default settings except for lithium batteries.

CAUTION! All steps must be carried out when the PV modules are disconnected from the controller.

Step 1: D00 (Load Working Time)

Press the PRG button, then the LCD displays D00. This sets the load working time (default is 24-hour). Press ENT until numbers flash, then use UP/DOWN to set the desired time. Long-press ENT to confirm. The output voltage is the same as the battery. The load is only for small DC loads less than 5A current. If no load, leave it.

Step 2: D01 (Floating Charging Voltage)

Press the UP button, LCD shows 13.8 (default value). Press ENT until numbers flash, then use UP/DOWN to set the desired voltage. Long-press ENT to confirm.

CAUTION! This value is for one 12V battery. If there are multiple batteries in series, the controller will automatically multiply them in proportion. The LCD will only display the voltage of one battery (e.g., for a 4x12V battery, if you set 14.1V, the charge voltage will be 4x14.1V, but the LCD will only display 14.1V).

Step 3: D02 (Absorption Charging Voltage)

Continue to press the UP button, LCD shows 14.5 (highest absorption charging voltage). Press ENT until numbers flash, then use UP/DOWN to set the desired voltage. Long-press ENT to confirm.

Step 4: D03 (Battery Discharge Protection)

Continue to press the UP button, LCD shows 10.0 (protection value for battery discharge). Press ENT until numbers flash, then use UP/DOWN to set the desired voltage. Long-press ENT to confirm. This means it’s protected when a 12V battery is less than 10.0V and there is no output power from OU+ and OU-.

Step 5: D04 (Battery Voltage Calibration)

Continue to press the UP button, LCD shows C12.2. This setting calibrates the battery voltage by adjusting the value, ensuring the controller's detected battery voltage matches the actual battery voltage.

Step 6: D05 (Battery Type Setting)

Continue to press the UP button, LCD shows the battery type setting program. The default option is USE. Available battery types:

Battery TypeDescription
SELSealed Lead-Acid Battery
GELGel Sealed Lead-Acid Battery
FLdFlooded Lead-Acid Battery
L044-series Lithium Iron Phosphate Battery
L088-series Lithium Iron Phosphate Battery
L1515-series Lithium Iron Phosphate Battery
L1616-series Lithium Iron Phosphate Battery
USEUser-defined Battery Type

CAUTION! When selecting SEL, GEL, and FLd battery types, the controller automatically detects the system voltage.

Step 7: D06 (System Voltage for User-defined Battery Type)

If you choose the USE option in D05, you will need to manually configure the system voltage in the D06 setup program. The configuration range is 12V/24V/36V/48V.

Press ESC to exit the setting menu.

Reminder: After setting all steps, disconnect the battery and then reconnect the controller to confirm settings. Once settings are successful, connect PV modules to the controller.

4. Maintenance

To ensure optimal performance and longevity of your PowMr MPPT 60A Solar Charge Controller, regular maintenance is recommended:

  • Cleanliness: Keep the controller free from dust and debris. Ensure ventilation openings are clear to allow for proper airflow and cooling.
  • Connections: Periodically check all wiring connections (PV, battery, load) to ensure they are tight and free from corrosion. Loose connections can lead to power loss or overheating.
  • Battery Health: Monitor your battery's state of charge and overall health. Ensure proper ventilation around batteries, especially lead-acid types, to dissipate any gases produced during charging.
  • Environmental Conditions: Ensure the controller is installed in a cool, dry, and well-ventilated area, away from direct sunlight, moisture, and flammable materials.
  • Firmware Updates: Check the manufacturer's website periodically for any available firmware updates that might improve performance or address known issues.

5. Troubleshooting and Protections

The controller includes multi-function protection features to ensure safe operation and easy troubleshooting.

Multi-function protection icons for the solar charge controller

Image: Icons representing various protection features: Load short circuit, Battery over discharge, Battery reverse polarity, PV short circuit, PV over current alarm, Battery overcharge, Controller overheating, and Load overload protection.

Troubleshooting Guide

CodeDescriptionHow to solve
18Input PV voltage is lowIncrease the PV voltage
60Over-temperature protectionFan will work and temperature reduction automatically
63Battery voltage is highBattery high voltage protection and wait for recovery
65Battery voltage is lowBattery over-discharge and wait for recovery
71Input PV voltage is highDecrease the PV voltage
73Over-charging currentDecrease the PV power

Protections

  1. PV Over Current: The controller will limit charging power to its rated charge power. An over-sized PV array will not operate at maximum power point.
  2. PV Short Circuit: When a PV short circuit occurs, the controller will stop charging. Remove the short circuit to resume normal operation.
  3. PV Reverse Polarity: Full protection against PV reverse polarity, causing no damage to the controller. Correct the connection to start normal operation.
  4. Battery Over Voltage: If other energy sources charge the battery, and the battery voltage exceeds 15.5V (for 12V system), 31.0V (for 24V system), 46.5V (for 36V system), or 62.0V (for 48V system), the controller will stop charging to protect the battery from overcharging damage. (Note: "stop charging" means charging current becomes very low).
  5. Battery Over Discharge: When battery voltage drops to the set low voltage disconnect point, the controller will stop discharging to protect the battery from over-discharging damage.
  6. Load Over Current Protection: If the load current exceeds 1.25 times the maximum load current rating, the controller will disconnect the load.
  7. Load Short Circuit Protection: Once a load short circuit happens, the load short circuit protection will activate automatically.
  8. Over Temperature Protection: The controller will reduce output power if its internal temperature exceeds 70°C and resume normal operation when it drops below 55°C. The fan will activate if the temperature exceeds 40°C and turn off below 35°C.

6. Specifications

FeatureSpecification
Model No.HHJ-60A Board Set
Charging mode3-stage (MPPT, Absorption, Floating)
System typeDC12V/24V/36V/48V Recognition automatically
12V System Voltage RecognitionDC9V~DC15V
24V System Voltage RecognitionDC18V~DC29V
36V System Voltage RecognitionDC30V~DC39V
48V System Voltage RecognitionDC40V~DC60V
Soft start time≤1S
Dynamic response and recovery time100us
Max efficiency≥98.1% (Voc is 1.5 or 2 times than battery for best efficiency)
PV utilization≥99%
12V System Voc from PVDC20V~DC80V
24V System Voc from PVDC37V~DC105V
36V System Voc from PVDC50V~DC160V
48V System Voc from PVDC72V~DC160V
Maximum PV input voltage (Voc)DC190V (Controller cannot work at this voltage for long duration)
12V System Max. PV Input Power720W
24V System Max. PV Input Power1440W
36V System Max. PV Input Power2100W
48V System Max. PV Input Power2800W
Overcharging protection voltage60V
Limited current protection61A
Rated output current60A
Temperature Coefficient±0.02%/ centi-degree
Automatic temperature compensation14.2V-(Max temperature-25 centi-degree)*0.3
Output voltage ripple-peak100mV
Output voltage accuracy≤±1%
Input Anti-intrusion protectionYes
Temperature Protection75℃ / 167℉
Fan-on temperature>45℃ / 104℉
Fan-off temperature<35℃ / 95℉
Acoustic noise≤40dB
Cooling wayForced air cooling
ComponentsImported materials, Accord to EU standards, Industrial grade range.
Environmental requirementsMeet 2002/95/EC; No cadmium, hydrides and fluorides
Security LevelAccord to CE, PSE, FCC, EMC, EN60950
Electromagnetic CompatibilityAccord to EN61000, EN55022, EN55024
EnclosureIP21
Size (mm)/(in)214x115x50mm/ 8.43x4.53x1.97in
Net weight(Kg)/(Ib)1.1/2.43
Gross weight(Kg)/(Ib)1.2/2.65
Environmental temperature-20℃ ~ +55℃
Storage temperature-40℃ ~ +75℃

7. User Tips

  • Proper Sizing: Ensure your solar panel array and battery bank are correctly sized for the controller's specifications to maximize efficiency and prevent damage.
  • Ventilation: Always ensure adequate ventilation around the controller and batteries to prevent overheating and gas buildup.
  • Battery Type Selection: Accurately select your battery type in the settings (D05) for optimal charging and battery longevity. For lithium batteries, manual voltage configuration (D06) is crucial.
  • Initial Setup: Follow the connection sequence strictly: Battery first, then PV. Disconnect PV before making any changes to battery settings.
  • Monitoring: Regularly check the LCD display for system status and any fault codes to address issues promptly.

8. Warranty and Support

Warranty Regulations

According to the prescription, any damaged unit caused by the user's failure to install, disassemble, or incorrect use of this product may provide maintenance.

  1. Within 30 days from the date of purchase, a faulty controller will be replaced free of charge under normal use (with authorized technical personnel).
  2. Within 2 years from the date of purchase, a faulty controller will be repaired free of charge.

Notes: Disassembled privately, no warranty.

Liability Disclaimer

The manufacturer shall not be liable for damages, especially to the battery, caused by use other than as intended or as mentioned in this manual, or if the recommendations of the battery manufacturer are neglected. The manufacturer shall not be liable if service or repair has been carried out by any unauthorized person, due to unusual use, wrong installation, or bad system design.

Content Included

  • 1x MPPT Solar Charge Controller
  • 4x Corner connections
  • 4x Screws for controller casing
  • 1x English manual

Contact Information

SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD

  • Tel/Fax: +86 755-28219903
  • Email: support@powmr.com
  • Web: www.powmr.com
  • Add: Henggang Street, Longgang District, Shenzhen, Guangdong, China

PDF User Manual: For a detailed user manual, please refer to the official PDF document available at PowMr MPPT Solar Charge Controller User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.