BUCKLOS B724

Contents

BUCKLOS B724 MTB Boost Air Suspension Fork User Manual

Model: B724 | Brand: BUCKLOS

1. Introduction

Thank you for choosing the BUCKLOS B724 MTB Boost Air Suspension Fork. This manual provides essential information for the proper installation, operation, and maintenance of your new suspension fork. Please read this manual thoroughly before installation and use to ensure optimal performance and safety.

BUCKLOS B724 MTB Boost Air Suspension Fork in black and orange
BUCKLOS B724 MTB Boost Air Suspension Fork (Black and Orange variants)

2. Specifications

The BUCKLOS B724 is an Oil and Gas Fork (Air Resilience/Oil Damping) designed for mountain, downhill, and e-bikes. Key specifications are detailed below:

FeatureSpecification
Brand NameBUCKLOS
ModelB724
TypeOil and Gas Fork (Air Resilience/Oil Damping)
UseMountain Bike / Downhill Bike / E-Bike
Wheel Size27.5 inch / 29 inch
MaterialAluminum Alloy
Fit ForDisc Brake
Suspension TypeAir Suspension
Travel180mm
Lockout WayManual Lockout
Axle Type15*110mm Thru Axle
Steerer Tube TypeTapered Tube
Steerer Tube Diameter28.6mm (1-1/8'' Threadless)
Steerer Tube Length220mm
Crown Race39.8mm
Outer Tube Diameter38mm
Weight (Approx.)2650g
Offset51mm
Support Tyre Size3.0 Inch Maximum width cover tyre
Fork size diagram with dimensions for 27.5 and 29 inch models
Detailed dimensions for 27.5" and 29" fork models.

3. Setup and Installation

3.1 Compatibility Check

Before installation, ensure your bike is compatible with the BUCKLOS B724 fork. Verify the following:

  • Wheel Size: Compatible with 27.5 inch and 29 inch wheels.
  • Steerer Tube: 1-1/8 inch (28.6mm) threadless tapered tube. The length is 220mm.
  • Axle Type: 15*110mm Thru Axle (Boost spacing).
  • Brake System: Designed for disc brakes with an international A-pillar, PM pure disc brake direct loading function. The disc brake column distance is 75mm.
  • Tire Clearance: Supports tires up to 3.0 inches in width.

3.2 Installation Steps

  1. Prepare the Frame: Ensure your bike frame's head tube is clean and properly faced for a tapered steerer tube.
  2. Install Crown Race: Press the 39.8mm crown race onto the steerer tube.
  3. Insert Steerer Tube: Carefully insert the steerer tube through the head tube of your bike frame.
  4. Install Headset Components: Assemble your headset components according to the manufacturer's instructions.
  5. Cut Steerer Tube (if necessary): Measure and cut the steerer tube to the appropriate length for your bike and stem setup, leaving enough room for spacers and the top cap.
  6. Install Stem and Handlebars: Mount your stem and handlebars, ensuring all bolts are torqued to the manufacturer's specifications.
  7. Install Thru Axle: Insert the 15*110mm thru axle through the fork dropouts and wheel hub, then tighten securely.
  8. Mount Brake Caliper: Attach your disc brake caliper to the international A-pillar mount on the fork. Ensure proper alignment and torque the bolts to the brake manufacturer's specifications.
Brake support diagram showing measurements for disc brake mounting
Brake support details for disc brake caliper mounting.
Lower leg arch design for optimized stiffness and clearance
The optimized arch design provides ample headtube clearance.

4. Operating Your Suspension Fork

The BUCKLOS B724 fork features air suspension with adjustable compression and rebound damping, along with a manual lockout function.

Diagram showing fork functions: Compression Adjustment, Air Chamber, Brake Line Fixed Buckle, 15mm Thru Axle, Damping Adjustment, Removable Sticker
Overview of the fork's functional components.

4.1 Air Pressure Adjustment (Compression)

The air chamber allows you to adjust the compression damping effect by setting the appropriate air pressure. This should be done based on the rider's weight and riding conditions for a comfortable experience.

  • Locate the air valve cap (usually on the top of one fork leg, often blue).
  • Unscrew the cap and attach a high-pressure shock pump.
  • Add or release air to achieve your desired sag and compression feel. Refer to your bike's or a general suspension setup guide for recommended pressure ranges based on rider weight.
  • Replace the air valve cap securely.
Diagram of the air chamber, explaining its lightweight and shock-absorbing function
The air chamber uses gas as a rebound medium to adjust shock absorption.

4.2 Rebound Adjustment

The rebound damper has 14 gears, allowing you to fine-tune how quickly the fork extends after compression. This helps adapt to different terrains and rider preferences.

  • Locate the rebound adjustment knob (usually at the bottom of one fork leg, often red).
  • Turn the knob clockwise for slower rebound (more damping) or counter-clockwise for faster rebound (less damping).
  • Experiment with different settings to find what works best for your riding style and terrain.
Image of the damping adjustment knob with 14 stages, from Fast to Slow
Rebound adjustment knob with 14 stages for fine-tuning.

4.3 Manual Lockout

The manual lockout function allows you to stiffen the fork for climbing or smooth terrain, improving pedaling efficiency.

  • Locate the lockout knob (usually on the top of one fork leg, often blue, marked 'OPEN' and 'LOCK').
  • To lock the suspension, rotate the knob fully to the 'LOCK' position until it can no longer be rotated.
  • To unlock the suspension, rotate the knob fully to the 'OPEN' position until it can no longer be rotated.
  • Note: This function does not have segmented adjustment; it must be rotated fully to either the 'OPEN' or 'LOCK' state.
Image of the manual lockout knob with OPEN and LOCK positions
Manual lockout knob for stiffening the fork.

5. Maintenance

Regular maintenance will prolong the life and performance of your BUCKLOS B724 fork.

5.1 Cleaning

  • After each ride, especially in dirty or wet conditions, clean the outer surfaces of the fork, including the stanchions (inner tubes) and seals.
  • Use mild soap and water, and a soft cloth. Avoid high-pressure washers directly on seals.
  • Dry thoroughly.

5.2 Lubrication

The BUCKLOS B724 fork features Teflon sliding sleeves for excellent lubrication and reduced friction, along with internal oil absorbent cotton to protect the inner tube and efficiently absorb excess oil.

  • Lubricating Holes: There are two lubricating holes located behind the fork tube.
  • To lubricate, use a 3mm hexagonal screw to unscrew the screw on the lubricating hole.
  • Inject only 2-3ml of lubricating oil into each hole.
  • Replace the screw securely. This process improves smoothness and reduces friction and wear.
Diagram showing the lubricating hole and oiling method
Location of the lubricating hole and recommended oiling method.
Comparison of old plastic sliding sleeve vs. new Teflon sliding sleeve and absence of oil absorbent cotton vs. presence of oil absorbent cotton
The upgraded inner tube features Teflon sliding sleeves and oil absorbent cotton for improved performance and durability.
Diagram showing the oil absorbent cotton and its function
Oil absorbent cotton protects the inner tube and absorbs excess oil.

6. Troubleshooting

Here are some common issues and their potential solutions:

ProblemPossible CauseSolution
Fork does not achieve full travelExcess lubricant or oil inside the damper.Check for and remove any excess lubricant or oil that might be restricting full travel. Consult a professional if unsure.
Excessive friction or noise during compression/reboundLack of lubrication, worn sliding sleeves.Ensure proper lubrication using the lubricating holes. The fork is equipped with Teflon sleeves to minimize this, but regular maintenance is key.
Oil leakage from fork sealsDamaged seals, excessive internal pressure, or improper assembly.The fork includes internal oil seal foam to prevent leakage. If leakage occurs, inspect seals for damage. Contact support if the issue persists.
Lockout not engaging or disengaging properlyKnob not fully rotated, internal mechanism issue.Ensure the lockout knob is rotated fully to the 'LOCK' or 'OPEN' position. If the issue persists, professional inspection may be required.

7. User Tips

  • Initial Inspection: Upon receiving your fork, perform a thorough inspection. Some users have reported finding excess lubricant/oil inside the damper that can affect full travel. It's advisable to check this before initial use.
  • Compatibility is Key: Always double-check your bike's specifications (wheel size, steerer tube type, axle type, brake mount) against the fork's requirements to ensure a perfect fit.
  • Thru Axle vs. Quick Release: This fork uses a 15x110mm Thru Axle, which provides superior stiffness and security compared to a quick-release system. Ensure your wheel hub is compatible with a thru axle.
  • Steerer Tube Length: The steerer tube length is fixed at 220mm. Plan your headset stack height accordingly, as it cannot be extended.
  • Professional Installation: If you are not confident in installing the fork yourself, it is highly recommended to seek assistance from a qualified bicycle mechanic.

8. Warranty and Support

For any questions, concerns, or issues regarding your BUCKLOS B724 suspension fork, please contact the seller or BUCKLOS customer support. Provide your purchase details and a clear description of the problem for efficient assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.