JIKONG JK-B2AxxS-20PCC

Contents

JIKONG Smart Active Balance BMS User Manual

Model: JK-B2AxxS-20PCC

1. Introduction

The JIKONG Smart Active Balance BMS (Battery Management System) is an intelligent protection board designed for large-capacity series lithium battery packs. It integrates essential functions such as voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, over-temperature protection, coulomb metering, Bluetooth communication, and optional GPS remote functionality.

This BMS is compatible with various battery chemistries, including LiFePO4, Li-ion (ternary lithium), and LTO (lithium titanate) battery types. Its energy transfer active balancing technology ensures battery consistency, extends battery life, and improves overall range. The compact design, ease of operation, and comprehensive features make it suitable for a wide range of applications, including small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage systems, base station backup power supplies, and solar power stations.

2. Specifications

2.1. Basic Parameters

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<800mW
Operating Temperature-30-70°C
Max. Number of Collection Strings24String
Max. Balancing Current2A
Max. Charging Current200A
Max. Discharge Current200A
Max. Instantaneous Current300A
Max. Internal Loop Resistance0.65mΩ
Protective Plate Size169.6×101.7×20.12mm
Finished Weight480g

2.2. Default Parameters (Example for LiFePO4)

ParameterValueUnit
Balancing Initial Voltage3V
Maximum Balancing Current0.4A
Unit Overcharge Voltage3.6V
Single Overcharge Protection Recovery3.55V
Monomer Undervoltage Protection2.6V
Single Undervoltage Protection Recovery2.65V
Automatic Shutdown Voltage2.5V
Trigger Balancing Differential Pressure0.01V
Charging Overcurrent Protection Delay30S
Charging Overcurrent Protection Release Time60S
Discharge Overcurrent Protection Delay300S
Short-circuit Protection Delay1500µS
Short-circuit Protection Release Time60S
Charging Overtemperature Protection Temperature70°C
Charging Overtemperature Restore Temperature60°C
Discharge Overtemperature Protection Temperature70°C
Discharge Overtemperature Recovery Temperature60°C
Charging Low Temperature Protection Temperature-20°C
Charging Low Temperature Restore Temperature-10°C
MOS Overtemperature Protection Temperature100°C
MOS Overtemperature Recovery Temperature80°C
Device Address0/
Discharge Precharge Time0S

3. Package Contents

The package typically includes the following items:

  • JIKONG Smart Active Balance BMS (with Bluetooth built-in)
  • Operating Manual
  • Temperature Sensor (40cm)
  • Balance Wires (75cm)
  • Active Switch (15cm)
  • Screws (4 pcs)
  • Pack Box
  • Optional: CAN cable (25cm)
  • Optional: Heating cable (Only for BMS with Heat Function)
JIKONG Smart BMS Package Contents

Figure 1: Typical Package Contents for JIKONG Smart BMS

4. Setup Instructions

4.1. Unpacking and Inspection

Handle the package and BMS gently. Before opening, check for any signs of impact or damage. Ensure all components listed in the package contents are present and in good condition.4.2. Hardware Connection

The JIKONG BMS is suitable for 7-24 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack. Always refer to the detailed wiring diagram for your specific model.

  1. Balance Wires Connection: Connect the balance wires to each cell's positive terminal, starting from B0 (total negative pole) up to the last positive pole (e.g., B13 for a 13S battery). Ensure the black cable B0 connects to the total negative pole of the battery, and red cables B1, B2, etc., connect to the positive pole of each subsequent battery string. The last red cable connects to the total positive pole of the battery.
  2. BMS Connection: Connect the P- cable from the BMS to the negative pole of the charger. Connect the total positive pole of the battery to the positive pole of the charger.
  3. Verification: Use a multimeter to measure the voltage between adjacent balance wires. If the voltage difference between the batteries in each string of wires is less than 1V, it indicates correct wiring. Then, measure the total voltage of the battery pack by placing the black pin of the multimeter on the negative terminal and the red pin on the positive terminal. Finally, place the black pin on the P- cable port of the BMS (with the red pin remaining on the positive terminal) and measure the voltage. If both total voltage measurements are consistent, the cable connection is correct.
  4. Switch Connection: Connect the switch cable to the designated port on the BMS.
JIKONG Smart BMS Wiring Diagram

Figure 2: General Wiring Diagram for JIKONG Smart BMS

Video 1: JIKONG BMS Wiring Tutorial - Demonstrates the step-by-step process of connecting the BMS to a battery pack, including balance wires, P- cable, and charger connections.

4.3. Device Activation

Before powering on the protection board, double-check all balance cable connections and ensure the P- and B- connections are correct. Confirm the BMS is securely fixed to the battery pack. Incorrect connections can lead to malfunctions or damage.

The BMS is designed for charging activation. After the battery assembly is complete, connect the charger (charger voltage should be at least 2V higher than the battery voltage) to activate the BMS. Alternatively, if your model includes a display screen and button, you can activate the BMS by inserting the cable into the display interface and pressing the button.

BMS Interface Connections

Figure 3: BMS Interface Connections for RS485, Switch, and LCD Displays

5. Operating Instructions

5.1. APP Installation

The JIKONG Smart BMS is controlled via a mobile application available for both Android and iOS devices. To install the app:

  • For iOS: Search for "JIKONG BMS" in the Apple App Store.
  • For Android: Search for "JK BMS" in the Google Play Store. (Android Version 7 or higher is required).
JIKONG BMS APP QR Code

Figure 4: QR Code for Mobile APP Download

5.2. APP Connection and Parameter Setting

  1. Ensure Bluetooth is enabled on your mobile phone.
  2. Open the JIKONG BMS APP. Click on the top left corner to search for devices.
  3. Select your BMS from the device list. The default connection password is 1234.
  4. For the first-time setup, you will need to set parameters. The default parameter setting password is 123456.
  5. Set the correct number of battery cells (strings) and the battery type (Li-ion, LiFePO4, or LTO).
  6. After setting parameters, navigate to the real-time status page to monitor battery status. Blue indicates the highest cell voltage, and red indicates the lowest.
JIKONG Smart BMS APP Interface

Figure 5: Smart BT APP Interface for Monitoring and Control

5.3. Key Features and Functions

  • Active Equalization: Transfers energy from high-voltage cells to low-voltage cells to maintain battery consistency. The default balancing current is 2A. Users can adjust the balance current and trigger voltage difference via the APP.
  • Heating Function: Supports optional heating to prevent low-temperature charging/discharging issues. Heating is activated when battery temperature falls below a set threshold. The designed heating current is 4A. It is recommended to use a temperature control switch (45-65°C normally closed) in series for secondary protection.
  • Alarm Function: Provides external alerts for security risks such as over-temperature, overcharge, and over-discharge.
  • Battery Parallel Function: Supports parallel connection of battery packs, requiring a parallel module and disabling the
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.