1. Introduction
The Noyafa NF-918S is a versatile, multi-functional testing device designed for network and fiber optic professionals. It combines the capabilities of a network cable tester, optical power meter, PoE checker, and visual fault locator into a single, portable unit. This manual provides detailed instructions for the safe and effective use of your NF-918S.

Figure 1: Noyafa NF-918S Transmitter and Receiver Units
2. Safety Information
- The RJ45 interface of this device has a maximum voltage resistance of 60V. Do not connect network cables exceeding this voltage to prevent damage to the device.
- When using the Visual Fault Locator (VFL) function, avoid looking directly at the red light, as it can be harmful to your eyes.
- Ensure the device is fully charged before use to avoid interruptions during testing.
- Do not attempt to disassemble or repair the device yourself. Contact qualified personnel for service.
3. Package Contents
Verify that all items are present in your package:

Figure 2: NF-918S Package Contents
- Transmitter Unit
- Receiver Unit
- Packaging Box
- Instructions/Certificate
- Tool Kit
- RJ11 Alligator Clip Wire
- RJ11 Telephone Line
- RJ45 Interface Network Cable
- Headphones
- Charging Cable (Type-C)
4. Product Features and Components
4.1 Key Features

Figure 3: Nine Highlights of the NF-918S
- Cable Scan (SCAN): Locates target network cables among many. Offers Normal and Anti-jamming modes.
- Cable Continuity Testing (CONT): Detects line sequence, short circuits, open circuits, and crossovers in network cables (CAT5, CAT6) and telephone lines. Supports fast and slow modes.
- PoE Checker: Tests the power supply mode of PoE switches and identifies core connections.
- Quality Crystal Testing (QC): Tests RJ45-8P/RJ11 connections for quality, with a shortest length requirement of 10cm.
- Optical Power Meter (OPM): Measures optical power and light attenuation value across 6 wavelengths (850/1300/1310/1490/1550/1625nm).
- Visual Fault Locator (VFL): Provides a strong red light for fiber optic cable testing, with constant, fast flash, and slow flash modes.
- NCV Function: Non-Contact Voltage detection for AC power greater than 40V.
- LED Lighting: Equipped with a flashlight for working in dark environments.
- Low Battery Prompt: Visual indicators on both transmitter and receiver for low battery status.
4.2 Product Diagram: Buttons & Interfaces

Figure 4: Transmitter and Receiver Buttons & Interfaces
Transmitter:
- Optical Power Interface: For OPM measurements.
- Display Screen: Shows test results and settings.
- Line Sequence Lamps: Indicate cable continuity status.
- Cable Continuity Test Button (CONT LIGHT): Initiates continuity test.
- Optical Power Meter Button (OPM REF): For OPM reference settings.
- Power/Wavelength Button (WAVE): Turns on/off and cycles through OPM wavelengths.
- Scan Button (SCAN): Initiates cable scanning.
- QC Unit Button (QC UNIT): For crystal head quality testing.
- VFL LED Button (VFL LED): Activates Visual Fault Locator.
- VFL Interface: Output for Visual Fault Locator.
- QC Interface: For crystal head testing.
- CONT/SCAN Interface: RJ-45 port for continuity and scan functions.
Receiver:
- Power Indicator: Shows power status.
- Sensitivity Adjustment Knob (SEN): Adjusts signal sensitivity.
- SCAN Button: Initiates scanning.
- NCV Button: Activates Non-Contact Voltage detection.
- Signal Indicator: Visual feedback during scanning.
- Lamp Button: Activates LED lighting.
- RJ45 Port: For connecting network cables.
5. Setup
5.1 Charging the Device
The NF-918S units are powered by 3.7V 1400mAh polymer batteries and support Type-C charging. Use the provided charging cable to charge both the transmitter and receiver units before first use and whenever the low battery indicator appears.
5.2 Initial Power On
Press and hold the power button on each unit to turn them on. The display screen on the transmitter will light up, and the receiver's power indicator will illuminate.
6. Operating Instructions
6.1 Cable Continuity Testing (CONT)
This function checks for open circuits, short circuits, cross-overs, and correct wiring sequence in network (CAT5, CAT6) and telephone cables.
- Connect one end of the cable to the CONT/SCAN interface on the transmitter and the other end to the RJ45 port on the receiver.
- Press the 'CONT LIGHT' button on the transmitter.
- Observe the line sequence lamps on the transmitter and the display on the receiver. The results will indicate the cable's status (e.g., 'LI AE' for line error, or correct sequence).
- The device supports fast and slow modes for continuity testing.
- For STP cables, the 'G' LED on the receiver will light up.

Figure 5: Cable Continuity Test in Progress
6.2 Cable Scanning (SCAN)
The scanning function helps locate a specific network cable among a bundle of cables.
- Connect one end of the cable to the CONT/SCAN interface on the transmitter.
- Turn on the receiver and select the 'SCAN' function.
- Move the receiver's probe along the cables. The receiver will emit an audible 'beep' sound and illuminate the signal indicator when the target cable is detected.
- Normal Mode: Uses analog signals for quick cable finding.
- Anti-jamming Mode: Uses digital signals to minimize noise interference and provide high sensitivity for precise cable location, especially in complex environments.

Figure 6: Dual Mode Scanning Function

Figure 7: Direct Cable Continuity Test After Scanning
6.3 PoE Test
This function determines the power supply mode (End-Span or Mid-Span) of a Power over Ethernet (PoE) switch.
- Connect a network cable from the PoE switch to the RJ45 port on the receiver.
- The receiver will automatically detect the PoE power supply and indicate the active cores.
- End-Span PoE: Typically lights up cores 1, 2, 3, 6.
- Mid-Span PoE: Typically lights up cores 4, 5, 7, 8.
- 8-core PoE: Lights up cores 1, 2, 3, 6 and 4, 5, 7, 8.

Figure 8: PoE Test Core Connection
6.4 Optical Power Meter (OPM)
The OPM measures the optical power and attenuation in fiber optic cables.
- Connect the fiber optic cable to the Optical Power Interface on the transmitter.
- Press the 'WAVE' button to cycle through the available wavelengths: 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. Select the appropriate wavelength for your test.
- The display will show the optical power measurement in dBm.
- Use the 'OPM REF' button to set a reference value if needed for attenuation measurements.

Figure 9: Optical Power Meter Function
6.5 Visual Fault Locator (VFL)
The VFL function injects a visible red laser light into a fiber optic cable to quickly locate breaks, bends, or faulty connectors.
- Connect the fiber optic cable to the VFL Interface on the transmitter.
- Press the 'VFL LED' button to activate the red light.
- The VFL offers three modes: constant light, fast flash, and slow flash. Cycle through these modes by pressing the 'VFL LED' button repeatedly.
- Visually inspect the fiber cable for any escaping red light, which indicates a fault.

Figure 10: Visual Fault Locator (VFL) in Use
6.6 NCV Function (Non-Contact Voltage)
The NCV function allows for safe detection of live AC voltage without direct contact.
- Activate the NCV function on the receiver by pressing the 'NCV' button.
- Bring the top of the receiver close to wires, sockets, or other equipment where AC power is suspected.
- If AC power greater than 40V is detected, the receiver will emit a 'beep' sound, indicating the presence of live voltage.

Figure 11: NCV Function Detecting Live Voltage
6.7 LED Lighting
The receiver unit includes an LED flashlight for improved visibility in dimly lit work areas.
- Press the 'Lamp' button on the receiver to turn the LED light on or off.

Figure 12: LED Lighting for Dark Environments
7. Maintenance
- Keep the device clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
- Store the device in a cool, dry place when not in use.
- Regularly charge the batteries to maintain their lifespan, even if the device is not used frequently.
- Avoid dropping the device or subjecting it to strong impacts.
- Do not expose the device to extreme temperatures.
8. Troubleshooting
- Device not powering on: Ensure the batteries are fully charged. If the issue persists, contact support.
- Inaccurate test results: Check cable connections for proper seating. Ensure the correct test mode is selected. Clean interfaces if necessary.
- No signal during scanning: Adjust the sensitivity knob on the receiver. Ensure the transmitter is powered on and connected to the cable.
- Does the device measure cable distance? The Noyafa NF-918S is designed for continuity, scanning, PoE detection, optical power measurement, and visual fault locating. It does not include a function for measuring cable length or distance.
- Low battery prompt: Recharge the device using the Type-C charging cable.
9. Specifications

Figure 13: Product Parameters
| Feature | Specification |
|---|---|
| Model Number | NF-918S |
| Brand Name | NOYAFA |
| Certification | CE |
| Maintester Dimension (LxWxD) | 133x69x32mm |
| Receiver Dimension (LxWxD) | 198x50x32mm |
| Cable Type Supported | CAT5, CAT6 (Network), RJ11 (Telephone) |
| Interface Withstand Voltage | 60V |
| Optical Power Measurement Range | -70~10dbm |
| VFL Wavelengths | 850/1300/1310/1490/1550/1625nm |
| Red Light Pen Test Power | 10mw |
| Charging Method | Type-C charging |
| Battery Type | 3.7V 1400mAh Polymer Battery (Included) |
| Is Smart Device | No |
| Auto Power-off (Transmitter) | 30 minutes (can be turned off) |
| Sensitivity Adjustable (Receiver) | Yes |
| NCV Function | Yes |
| LED Lighting | Yes |
| Low Voltage Prompting | Yes (Power supply indicator flashes < 3.5V ± 0.1V) |
10. User Tips
- For accurate cable scanning, especially in noisy environments, utilize the 'Anti-jamming Mode' to reduce interference.
- When performing continuity tests, ensure both ends of the cable are securely connected to the respective units for reliable results.
- Always check the battery level before starting a critical task to avoid interruptions.
- Remember that this device does not measure cable length. Its primary functions are continuity, tracing, and optical power/fault detection.
11. Warranty and Support
NOYAFA products are manufactured under strict quality control standards. For warranty information, technical support, or service inquiries, please refer to the contact details provided with your product packaging or visit the official NOYAFA website.
Video 1: Noyafa Company Overview and Quality Assurance