ASAIR AGP10

Contents

ASAIR AGP10 MEMS Diffused Silicon Pressure Transmitter Sensor User Manual

Model: AGP10 Series

1. Introduction

The ASAIR AGP10 series is a high-performance MEMS diffused silicon pressure transmitter sensor designed for precise vacuum measurement. Utilizing piezoresistive theory, this corrosion-resistant metal sensor is ideal for demanding applications in vacuum packaging, semiconductor manufacturing, and various industrial equipment. This manual provides essential information for the safe and effective installation, operation, and maintenance of your AGP10 sensor.

ASAIR AGP10 Pirani vacuum gauge with key features
Figure 1: ASAIR AGP10 Pirani Vacuum Gauge highlighting ±0.5%FS accuracy, 5~45°C operating temperature, and 1-5V analog voltage output.

2. Specifications

The AGP10 series offers robust performance for industrial vacuum measurement. Key specifications are detailed below:

FeatureSpecification
Brand NameASAIR
ModelAGP10 (e.g., AGP1013 variant)
TheoryPiezoresistive
TypeVacuum Sensor
MaterialMetal
Measurement Range0-100 Torr, 0-1000 Torr (model dependent)
Power Input+15-24VDC
Output1-5VDC / RS485 (Digital Sensor)
Accuracy±0.5%F.S.
Operating Temperature5~45°C
ApplicationVacuum packaging, semiconductor, Industrial equipment
OriginMainland China
Original ManufacturerGuangzhou Aosong
Detailed specifications of AGP1013 model, including range, output, input, and accuracy.
Figure 2: Detailed specifications for a specific AGP10 variant (AGP1013).

3. Setup and Installation

Proper installation is crucial for accurate and reliable performance of your AGP10 sensor. Follow these steps carefully:

  1. Mounting: Securely mount the sensor to your vacuum system. Ensure the connection point is clean and free from debris to prevent leaks. The sensor is designed for vacuum applications and should be installed in a manner that minimizes mechanical stress.
  2. Power Connection: Connect the sensor to a stable power supply providing +15-24VDC. Refer to the sensor's labeling or specific model documentation for exact pin assignments if not clearly marked on the connector.
  3. Output Connection: Connect the sensor's output to your data acquisition system or controller. The sensor provides either a 1-5VDC analog output or an RS485 digital output, depending on the specific model purchased. Ensure your receiving equipment is configured to interpret the correct signal type.
  4. Environmental Considerations: Operate the sensor within its specified temperature range of 5~45°C. Avoid exposing the sensor to extreme temperatures, vibrations, or corrosive environments beyond its design limits.
Side view of the AGP10 sensor showing the electrical connector.
Figure 3: Side view of the AGP10 sensor, illustrating the robust electrical connector.

4. Operating Instructions

Once installed and powered, the AGP10 sensor will begin measuring vacuum pressure. Follow these guidelines for operation:

  1. Power On: Apply the specified +15-24VDC power. Allow a brief warm-up period for the sensor to stabilize.
  2. Reading Output: Monitor the pressure readings from your connected data acquisition system or controller. The output will correspond to the measured vacuum pressure within the sensor's specified range (e.g., 0-100 Torr or 0-1000 Torr).
  3. Zero Adjustment: The sensor features a 'ZERO' button for calibration. In a known vacuum (e.g., atmospheric pressure or a reference vacuum), press and hold the 'ZERO' button to re-calibrate the sensor's zero point. This helps maintain accuracy over time.
Side view of the AGP10 sensor showing the 'ZERO' button for calibration.
Figure 4: The 'ZERO' button on the AGP10 sensor for calibration.

5. Maintenance

The ASAIR AGP10 sensor is designed for durability and corrosion resistance, requiring minimal maintenance. However, periodic checks can ensure optimal performance:

  • Cleaning: Keep the exterior of the sensor clean and free from dust or contaminants. Use a soft, dry cloth. Do not use abrasive cleaners or solvents that could damage the housing or seals.
  • Connection Integrity: Periodically inspect electrical and vacuum connections for tightness and signs of wear or corrosion. Ensure all seals are intact to prevent vacuum leaks.
  • Calibration Check: If precise measurements are critical, periodically verify the sensor's calibration against a known reference or recalibrate using the 'ZERO' button as described in the operating instructions.
  • Storage: If storing the sensor for an extended period, ensure it is kept in a clean, dry environment within the recommended temperature range.

6. Troubleshooting

If you encounter issues with your AGP10 sensor, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No output or incorrect readings
  • Incorrect power supply voltage
  • Loose or faulty wiring
  • Sensor not properly calibrated
  • Vacuum leak in the system
  • Sensor outside operating temperature range
  • Verify power supply is +15-24VDC
  • Check all electrical connections for secure fit
  • Perform zero adjustment/calibration
  • Inspect vacuum system for leaks
  • Ensure ambient temperature is within 5~45°C
Unstable readings
  • Electrical interference
  • Vibrations
  • Fluctuations in vacuum system
  • Ensure proper grounding and shielding of cables
  • Mount sensor away from sources of vibration
  • Stabilize the vacuum system
Sensor not responding to vacuum changes
  • Sensor failure
  • Clogged vacuum port
  • Contact technical support for assistance
  • Inspect and clean the sensor's vacuum port

7. User Tips

  • Application Specificity: The AGP10 is a vacuum pressure sensor. It is not designed to measure humidity or other gas properties. Ensure its application aligns with its intended function as a pressure gauge.
  • Range Selection: When purchasing, select the appropriate measurement range (e.g., 0-100 Torr or 0-1000 Torr) that best suits your application's vacuum levels to ensure optimal accuracy.
  • Calibration: Regular zero-point calibration, especially after initial installation or significant environmental changes, can significantly improve measurement accuracy.

8. Warranty and Support

For technical support, warranty claims, or further inquiries regarding your ASAIR AGP10 sensor, please contact the original manufacturer, Guangzhou Aosong, or your authorized distributor. Provide your product model (AGP10) and any relevant serial numbers for efficient service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.