1. Introduction
The BSIDE EMT01 is a professional handheld digital wood moisture meter designed for accurately measuring the moisture content of various wood types, paperboard, and dry cargo. It utilizes the electrical resistance principle for precise measurements and features a large HD LCD display for clear readings. This manual provides detailed instructions for the safe and effective use of your device.
2. Safety Information
- The electrode measurement pins are extremely sharp. Exercise caution when handling the instrument to prevent injury.
- Always cover the pins with the protective cap when the instrument is not in use.
- Do not attempt to measure live electrical circuits. This device is for wood moisture measurement only.
- Keep the device away from water and high humidity environments to prevent damage.
- Do not expose the device to extreme temperatures or direct sunlight.
- Keep out of reach of children.
3. Product Overview
- Measurement pins
- Low battery icon
- LCD measurement reading
- Hold indicator
- Wood group designators (A, B, C, D)
- Power on-off button
- Mode button to select wood groups
- Hold button
- Simply description of each wood group
4. Setup
4.1 Battery Installation
- Locate the battery compartment cover on the back of the device.
- Slide or unclip the cover to open it.
- Insert one 9V battery, ensuring correct polarity (+/-).
- Replace the battery compartment cover securely.
Note: Batteries are not included in the package.
5. Operating Instructions
5.1 Power On/Off
- Press the red Power On-Off button (6) to turn the meter on.
- The meter will automatically power off after approximately 15 minutes of inactivity to conserve battery life.
- To manually turn off, press and hold the Power On-Off button (6).
5.2 Selecting Wood Groups
The meter has four built-in wood patterns (A, B, C, D) for precise testing across different wood species. Refer to the 'Wood Species Group Table' below to identify the correct group for your material.
- With the meter powered on, press the 'MODE' button (7) to cycle through the wood groups (A, B, C, D).
- Select the group that corresponds to the wood species you are testing. The selected group will be indicated on the LCD display (5).
| Group | Wood Species |
|---|---|
| A | Teak, Walnut, Afromosia, Rubber Tree, Imbuia, Kokrodua, Niove Bidinkala, Cork |
| B | Keruing, White Poplar, Beech, Cedar, Tola |
| C | Lauan, Ash, Elm, Fir, Maple, Padauk, Oak, Cherry |
| D | Basswood, Larch, Pine, Birch |
5.3 Taking a Measurement
- Ensure the correct wood group is selected.
- Carefully remove the protective cap from the measurement pins.
- Firmly press the measurement pins (1) into the surface of the wood or material you wish to test. Ensure both pins penetrate the material.
- Read the moisture value displayed on the LCD screen (3). The value will be shown as a percentage (%).
- Once the measurement is complete, gently remove the pins from the material.
Video 1: Demonstration of the wood moisture meter in use.
5.4 Hold Function
To freeze the current measurement reading on the display:
- While taking a measurement, press the 'HOLD' button (8). The 'HOLD' indicator (4) will appear on the LCD.
- The displayed value will remain fixed, allowing you to record it.
- Press the 'HOLD' button (8) again to release the hold function and resume live measurements.
6. Maintenance
- Cleaning: Wipe the meter with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Storage: When not in use, always replace the protective cap over the measurement pins. Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for an extended period, remove the battery to prevent leakage.
- Battery Replacement: If the low battery icon (2) appears on the display, replace the 9V battery as soon as possible to ensure accurate readings.
7. Troubleshooting
- No Display/Meter Not Turning On:
- Check if the battery is installed correctly with the right polarity.
- Replace the 9V battery with a new one. - Inaccurate Readings:
- Ensure the correct wood group is selected for the material being tested.
- Make sure the measurement pins are fully inserted into the material.
- Check if the pins are clean and free from debris or corrosion.
- Replace the battery if the low battery indicator is on. - 'HOLD' Indicator Stuck:
- Press the 'HOLD' button again to release the function.
8. Specifications
| Feature | Description |
|---|---|
| Display Type | DIGITAL (Large LCD characters display) |
| Measurement Principle | Electrical resistance |
| Measurement Range | Wood: 0 - 99.9% |
| Resolution | 0.1% |
| Accuracy | ±0.5% |
| Electrode Length | 10mm (0.4") |
| Electrode Pins | Integrated |
| Auto Power Off | After approx. 15 minutes |
| Power Supply | 1 x 9V battery (not included) |
| Meter Housing | ABS plastic |
| Operating Temperature | 0 to 40°C (32 to 104°F) |
| Dimensions | 145 x 67 x 32mm (5.7" x 2.6" x 1.3") |
| Weight | 200g (7.0 oz) |
| Backlight | Yes |
| Certification | CE, FCC, RoHS |
9. User Tips
- For consistent readings, try to insert the pins to a similar depth each time.
- When testing rough or uneven surfaces, ensure good contact with both pins.
- If testing a large piece of wood, take multiple readings at different points and average them for a more representative moisture content.
- Remember to select the correct wood group for the most accurate results.
10. Warranty and Support
This BSIDE EMT01 Digital Wood Moisture Meter comes with a 1-year warranty. For technical support, warranty claims, or further assistance, please contact the BSIDE International Store directly through your purchase platform. Please retain your proof of purchase for warranty validation.
