1. Introduction
This manual provides detailed instructions for the operation and maintenance of your RETEKESS FT11 FM Transmitter and V112 FM Receiver Wireless Tour Guide System. This system is designed to facilitate clear communication in various settings such as guided tours, conferences, factory visits, and educational environments. The system includes one FT11 transmitter with a microphone for the speaker and multiple V112 receivers with earphones for listeners, ensuring every message is heard clearly even in noisy surroundings.
Note: The product interface for the FT11 transmitter has been updated to a Type-C interface. Older and newer versions may have minor differences in details, but this does not affect functionality.
2. Safety Information
2.1. General Warnings
Before using this radio, please read this guide carefully. It contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
2.2. RF Exposure Compliance
Your Retekess radio is designed and tested to comply with national and international standards and guidelines for human exposure to radio frequency electromagnetic energy. This device complies with IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
2.3. Avoid Choking Hazard
The system contains small parts. Keep out of reach of children under 3 years to prevent choking hazards.
2.4. Turn Off Radio Power in Specific Conditions
- Turn off your radio before removing (installing) a battery or accessory or when charging the battery.
- Turn off your radio when you are in potentially hazardous environments: Near electrical blasting caps, in a blasting area, in explosive atmospheres (inflammable gas, dust particles, metallic powders, grain powders, etc.).
- Turn off your radio while taking on fuel or while parked at gasoline service stations.
2.5. Avoid Electromagnetic Interference and/or Compatibility Conflicts
- Turn off your radio in any facility where posted notices instruct you to do so, especially in hospitals or health care facilities where sensitive medical equipment (Pacemakers, Hearing Aids, etc.) may be in use.
- Turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.
2.6. Avoid Burns (Antennas & Batteries)
- Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with the skin when the radio is in use, a minor burn can result.
- When conductive material such as jewelry, keys, or chains touch exposed terminals of the batteries, it may complete an electrical circuit (short circuit the battery) and become hot, causing bodily injury such as burns. Exercise care in handling any battery, particularly when placing it inside a pocket, purse, or other container with metal objects.
- When the transceiver is used for long transmissions, the radiator and chassis may become hot.
3. Package Contents
The package includes the following items:
- 1 x FT11 FM Transmitter
- 1 x Antenna for FT11
- 1 x USB charging cable (for FT11)
- 1 x Wired microphone
- 1 x Hand strap (for FT11)
- 1 x English manual for FT11
- 15 x V112 Radio Receiver
- 15 x Earphones (for V112)
- 15 x USB charging cable (for V112)
- 15 x Manuals for V112 (English/Spanish/German/French/Italian)
4. Product Overview
4.1. FT11 FM Transmitter
4.2. V112 FM Receiver
5. Setup Guide
5.1. Charging the Devices
The FT11 transmitter and V112 receivers have built-in rechargeable lithium batteries.
- FT11 Transmitter: Connect the FT11 to a USB power supply (DC 5V 1A) using the provided Micro USB charging cable. The transmitter can be charged whether it is on or off.
- V112 Receiver: Connect the V112 to a DC 5V power source using its Micro-USB jack. Charging time is approximately 2-3 hours.
5.2. Installing TF Card (FT11 Transmitter)
Insert a Micro SD card (TF card, Max 32GB) into the TF card slot on the side of the FT11 transmitter. Ensure it is inserted correctly. The main interface will display the card icon upon successful insertion.
5.3. Connecting Microphone (FT11 Transmitter)
Plug the wired microphone into the external microphone slot on the FT11 transmitter. The main interface will display a microphone icon, indicating a successful connection. The external microphone takes priority over the built-in microphone.
5.4. Connecting Earphones (V112 Receiver)
Plug the earphones into the 3.5mm audio jack on the V112 receiver. The earphones act as the antenna for the receiver.
6. Operating Instructions
6.1. Power ON/OFF
- Power ON: Slide the power switch down. The green part below the switch will become visible, and the transmitter will enter work mode.
- Power OFF: Slide the power switch up. The red part below the switch will become visible, and the transmitter will stop working.
6.2. Main Interface Operation (FT11 Transmitter)
- [Play/Pause] (►▮▮ button): In TF mode or computer sound adapter mode, short press to play or pause audio.
- [Previous] (◀◀ button): In TF mode or computer sound adapter mode, short press to play the previous video/audio.
- [Next] (►► button): In TF mode or computer sound adapter mode, short press to play the next video/audio.
- [Volume] (▲ / ▼ buttons): Long press ▼ to decrease volume, long press ▲ to increase volume.
- [Built-in Microphone] (● button): Hold and press to turn on the built-in microphone. Release the button to turn it off.
- [Turn on screen/Return] (● button): Short press to light up the screen and return to the main interface.
6.3. FM Frequency Setting (FT11 Transmitter)
Press the [F] button repeatedly to cycle through settings:
- Frequency: When "Frequency" appears, use the ◀◀ or ►► buttons. Short press adjusts frequency by 100KHz, long press by 1MHz.
- RF Power: When "RF Power" appears, use the ◀◀ button to decrease power rate and ►► button to increase power rate. (Low power rate is recommended for small area usage, e.g., in a car).
- Built-in MIC: When "Built in MIC" appears, use the ◀◀ or ►► buttons to select microphone settings:
- External MIC: Turns off the built-in microphone.
- MIC ON By Key: Turns on the built-in microphone when the ● button is pressed.
- MIC Always ON: The built-in microphone is always ready.
6.4. MP3 Setting (FT11 Transmitter)
Press the [M] button repeatedly to cycle through MP3 settings:
- MIC VOL: When "MIC VOL" appears, use ◀◀ to decrease mic volume and ►► to increase mic volume.
- MIC ECHO: When "MIC ECHO" appears, use ◀◀ to decrease echo volume and ►► to increase echo volume.
- MIC Delay: When "MIC Delay" appears, use ◀◀ to decrease mic delay and ►► to increase mic delay.
- EQ: When "EQ" appears, use ◀◀ or ►► to set sound effects for the whole kit.
- Repeat: When "Repeat" appears, use ◀◀ or ►► to set MP3 cycle mode.
- BASS: When "BASS" appears, use ◀◀ or ►► to set bass for the whole kit.
- TREB: When "TREB" appears, use ◀◀ or ►► to set tone for the whole kit.
- Language: When "Language" appears, use ◀◀ or ►► to set the language for the whole kit.
6.5. Frequency Saving and Use (FT11 Transmitter)
Tune to your desired frequency, then long press the Save button until the frequency display flashes. This frequency is now saved. To switch to this frequency later, simply short press the Save button.
6.6. Audio Input & Playback (FT11 Transmitter)
- Audio Input: Connect an audio source device (e.g., phone, MP3 player) to the FT11's AUX input using a 3.5mm audio cable. The connector icon will appear on the display.
- USB Sound Card: Connect the FT11 to a computer via USB cable. The main interface will display a computer icon.
- TF Card Playback: Insert a TF card with MP3 files. The FT11 can play music directly from the card.
6.7. One-to-Many Broadcast Mode
One FT11 FM transmitter can be paired with numerous V112 FM receivers. As long as the receiver is tuned to the same frequency as the transmitter, it will receive the audio broadcast. This is ideal for group settings like tours or conferences.
6.8. Transmission Distance
The FT11 transmitter supports 3 levels of power output. In a relatively open area, the maximum transmission distance can reach 100 meters. This makes it suitable for various environments including meeting rooms, classrooms, and training institutions.
6.9. One Second Link
The transmitting frequency of the FT11 is adjustable between 76-108MHz. To link a V112 receiver, simply adjust its frequency to match the transmitter's frequency. The signal will then be received instantly.
6.10. Noise Reduction
The system utilizes digital processing technology to effectively manage environmental noise, ensuring that every message is received clearly by the listeners.
6.11. Long Standby Time
The FT11 transmitter is equipped with a built-in high-capacity 1500mAh polymer lithium battery, providing approximately 6-8 hours of working time. The V112 receiver has a 500mAh rechargeable lithium battery, offering over 10 hours of working time.
7. Specifications
7.1. FT11 FM Transmitter Specifications
| Index | Data |
|---|---|
| Transmitter frequency | 76-108MHz |
| Pre-emphasis | 50us/75us |
| Output impedance | 50 Ω |
| SNR | ≥70dB |
| Frequency response | 30Hz~15000Hz |
| RF output power | 1mW-300mW, 3 levels |
| Support mp3 format | FLAC, WAV, WMA, MP3 |
| Support memory card | Max 32GB |
| Power Supply | Built-in 1500mAh li-poly battery |
| Working hours | About 6-8 hours |
| Charge Method | DC 5V 1A Micro USB jack |
| Size | 99 x 58 x 15mm / 3.9 x 2.2 x 0.6 in |
| Weight | 80g / 0.17lb |
7.2. V112 FM Radio Receiver Specifications
| Index | Data |
|---|---|
| FM Frequency | 64/87-108 MHz |
| AM Frequency | 520/522-1710 KHz |
| Built-in speaker | NO |
| Sensitivity | FM≤8uV, AM≤20mV/m |
| Power Supply | Built-in 500mAh rechargeable battery |
| Charge Method | DC 5V, Micro-USB jack |
| Charging time | 2-3 Hours |
| Working time | About 12 Hours |
| Size | 85 x 48 x 13 / 3.3 x 1.8 x 0.5 inch |
| Weight | 45g / 0.1lb |
8. Troubleshooting
If you encounter issues with your tour guide system, please refer to the following common solutions:
- No sound from receiver: Ensure the receiver's frequency matches the transmitter's frequency. Check the volume level on both devices. Verify earphones are properly connected.
- Poor sound quality/interference: Ensure the antenna on the FT11 is extended. Check for strong electromagnetic interference sources nearby. Try adjusting the RF power rate on the FT11 (lower power for smaller areas).
- Transmitter not turning on: Check battery level and ensure it's charged. Verify the power switch is in the ON position.
- TF card not playing: Ensure the TF card is inserted correctly and contains supported audio formats (FLAC, WAV, WMA, MP3).
- Microphone not working: Ensure the wired microphone is securely plugged in. Check the 'Built-in MIC' setting on the FT11 to ensure the correct microphone is active.
For more complex issues, please contact RETEKESS customer support.
9. User Tips
- For optimal sound clarity, especially in quiet environments, consider using the lowest RF power setting on the FT11 transmitter.
- When using the system for music transmission in a car, the low power rate mode is recommended to avoid interference.
- Utilize the frequency saving feature on the FT11 to quickly switch between commonly used frequencies for different groups or locations.
- Always fully charge both the transmitter and receivers before extended use to ensure uninterrupted operation.
10. Compliance Information
10.1. CE Marking
The CE marking indicates that Henan Eshow Electronic Commerce Co., Ltd. declares that the radio equipment type FT11 is in compliance with the RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available at www.tivdio.com.
10.2. IC ID
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode.
11. Warranty and Support
For technical support, repairs, or warranty inquiries, please contact RETEKESS customer service. Please do not attempt to repair the device yourself, as this may void the warranty and could cause further damage or injury. Repairs should only be operated by professional technicians.
EU Importer:
Name: Germany Retevis Technology GmbH
Address: Uetzenacker 29, 38176 Wendeburg