1. Introduction
Thank you for purchasing the Godox V1 Pro TTL Li-ion Round Head Camera Flash. This flash unit is designed for Canon EOS series cameras and is compatible with E-TTL II auto flash. It offers a simpler and better shooting experience, allowing for correct flash exposure even in complex light-changing environments.
Main Features:
- Round lens design for soft, even, and more creative light effects.
- 2W LED modeling lamp with 1 to 10 brightness adjustment.
- 76Ws flash power output at 1/1 step in M mode, with 81 adjustable steps from 1/1 to 1/256.
- Fully supports Canon E-TTL II camera flash, functioning as a transmitter or receiver unit in a wireless flash group.
- Dot-matrix LCD panel for clear and convenient operations.
- Built-in 2.4GHz wireless system for remote transmitting and receiving.
- Can be used with power pack PB960 for quicker recycle time.
- Supports detachable sub flash SU-1 for better filling light.
- Provides multiple functions, including manual flash, multi flash, HSS, Second-Curtain Sync, FEB, FEC, etc.
- Stable consistency in brightness and color temperature with good even lighting.
- Supports firmware upgrade for better compatibility with original cameras.
2. Important Safety Instructions
This product is a professional photographic equipment, to be operated by professional personnel only. All transport protective materials and packaging on the product must be removed before use.
- Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in death, serious injury, damage to the product, or other property damage.
- This product is a professional lighting fixture; children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
- This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
- Extreme caution must be exercised when using it; do not touch high-temperature parts such as flash tubes to avoid burns.
- Do not point the flash directly at the eyes (especially baby's eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
- Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
- Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
- This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
- Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
- Before storing the device, ensure it has completely cooled down.
- Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
- Do not use or store this device in potentially explosive environments.
- Maintain at least 1 meter distance between the lamp head and the user, other people, and heat-sensitive or flammable items during and after use.
- Do not use accessories not been approved by our company, as this may cause fire, electric shock or personal injury.
- Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
- This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check official website for latest instruction manual and product updates.
3. Parts Identification
Flash Body
- Flash Head
- LED Modeling Lamp
- Optical Sensor
- Focus Assist Beam
- External Flash Interface
- External Charging Port
- Bounce Angle Scale
- Hot Shoe
- LCD Panel
- Hot Shoe Fixing Buckle
- Lithium Battery
- Hot Shoe Lock Ring
- USB-C Charging Port
- Charging Indicator
Control Panel
- MENU/<Z> Button
- <Z> Wireless Button
- ON/OFF Power Switch
- Test Button / Recycle Indicator
- <+/->FEC/Flash Output Setting Button
- <ZOOM> Zoom Button
- <MODE> Mode Button
- LED Modeling Lamp Button
- Set Button
- Select Dial
- Function Button 1
- Function Button 2
- Function Button 3
- Function Button 4
Detachable Sub Flash SU-1
- Flash Tube
- Detaching Pusher
4. What's in the Box
The Godox V1 Pro package includes the following items:
- Flash Body x1
- Storage Bag x1
- Detachable Sub Flash SU-1 x1
- Lithium Battery x1
- USB-C Charging Cable x1
- Camera Flash Stand x1
- Charger x1
- Instruction Manual x1

Figure 4.1: What's in the Box
5. Optional Accessories
You can purchase the following accessories separately to enhance your photography experience:
- X2T TTL Wireless Flash Trigger
- XProII TTL Wireless Flash Trigger
- AK-R1 Round Flash Head Accessory Kit (includes diffuser dome, diffuser plate, bounce card, color filters, honeycomb grid, barn doors, snoot)
- AK-R21 Projection Attachment
- AK-R22 Dome Diffuser

Figure 5.1: AK-R1 Round Flash Head Accessory Kit

Figure 5.2: AK-R21 Projection Attachment and AK-R22 Dome Diffuser
6. Setup and Basic Operation
6.1 Battery Installation & Power Management
Detaching Battery:
Press and hold the battery remove button, then push the battery out of the battery compartment.
Installing Battery:
Insert the battery into the battery compartment in the direction indicated until it's firmly locked.
Battery Level Indication:
Check the battery level indication on the LCD panel to see the remaining battery level:
| Battery Level Indication | Meaning |
|---|---|
| 3 grids | Full |
| 2 grids | Middle |
| 1 grid | Low |
| Blank grid | Lower battery, please recharge it. |
| Blinking | The battery level is going to be used out, and the flash is not functional in this status. Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for long period. |
Power Management:
Use the ON/OFF power switch to power the flash unit on or off. Turn off if it will not be used for an extended period of time.
- Setting as a transmitter unit, the flash will turn the power off automatically after a certain period (approx. 90 seconds) of idle use. Press the camera shutter halfway or press any flash button will wake up the flash unit.
- Setting as a receiver flash, it will enter sleep mode after 60 minutes (or 30 minutes) of idle use. Pressing any flash button will wake it up.
6.2 Mounting/Detaching the Camera Flash
Mounting the Camera Flash:
- Press the hot shoe fixing buckle and rotate it to the left.
- Insert the camera flash into the camera's hot shoe.
- Rotate it to the right until it locks up.
Detaching the Camera Flash:
Press and rotate the hot shoe fixing buckle to the left until it is loosened, then take off the camera flash.
6.3 Detachable Sub Flash SU-1
The V1 Pro C features an external flash interface for the detachable Sub Flash SU-1. This allows for better fill light effects in M (manual) flash/TTL auto flash mode, which is helpful for portrait shooting.
Installing SU-1:
Align the detachable sub flash SU-1 with the external flash interface of V1 Pro C and insert it parallelly, then press it down. A "click" sound means it's properly installed.
Detaching SU-1:
Push the detaching pusher on SU-1 and pull it up at the same time to detach it.
Note: Please turn off the V1 Pro series flashes before installing and detaching SU-1. Do not insert or pull out SU-1 when the V1 Pro series flashes are in power on status or working, otherwise malfunctions may occur.
Using SU-1:
When the sub flash is turned on, you can adjust the flash output from 1/128 to 1/1 in 22 flash steps, with +1/3 increment each step.

Figure 6.1: V1 Pro with Detachable Sub Flash SU-1
7. Flash Modes
7.1 E-TTL Auto Flash
In ETTL mode, the camera's metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed. In this mode, multiple functions are available: FEC, FEB, FEL, HSS, second curtain sync, etc.
Flash Exposure Compensation (FEC):
This flash can adjust from -3 to +3 with 1/3 increment each step. It is useful in situations where minor adjustment of the TTL system is needed based on the environment.
Flash Exposure Bracketing (FEB):
FEB refers to the flash will automatically change the flash output for each shot from -3 to +3 with 1/3 increment each step. With this function, the camera will record three images with different exposures: one exposed according to camera calculations, one over-exposed and another under-exposed. This function helps get correct exposure especially in shooting moving objects or when environmental lights are complex.
Flash Exposure Lock (FEL):
FEL can lock the correct flash exposure setting for any part of the scene. With <ETTL> displayed on the LCD panel, press the camera's <FEL> button. If the camera does not have a <FEL> button, press the <*> button.
High-Speed Sync (HSS):
High speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.
Second-Curtain Sync:
With a slow shutter speed and second-curtain sync, you can create a light train following the subject. The flash fires right before the shutter closes.
7.2 Manual Flash (M)
The flash output is adjustable from 1/1 full power to 1/256 power with 1/10 increment each step. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.
7.3 Multi Flash (Stroboscopic Flash)
With slow shutter speed in multi flash mode, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph.
You can set the flash frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output.
8. Wireless Flash Shooting (2.4G Wireless Transmission)
This section explains wireless transmitting/receiving flash shooting. The V1 Pro C attached to the camera is referred to as the transmitter unit, while a V1 Pro C that is wirelessly controlled is referred to as the receiver unit.
You can also wirelessly control the V1 Pro C set as the receiver unit with the TTL flash trigger XPROII (sold separately). For details on setting the flash trigger functions, see its instruction manual.
8.1 Wireless Settings
You can switch between normal flash and wireless flash. For normal flash shooting, be sure to set the wireless setting to "OFF", and the <((()))> won't be displayed on the LCD panel.
Setting the Flash as a Transmitter Unit:
Press the <((()))> button so that <((()))> is displayed on the LCD panel, but the <RX> won't be displayed.
Setting the Flash as a Receiver Unit:
Press the <((()))> button so that <((()))> and <RX> are displayed on the LCD panel.
Wireless Channel Settings:
If there are other wireless flash systems nearby, you can change the wireless channels to prevent signal interference. The wireless channels of the transmitter unit and the receiver unit(s) must be set to the same.
ID Settings:
Change the wireless channels and wireless ID to avoid interference, as it can only be triggered after the wireless channels and IDs of the transmitter unit and the receiver unit are set to the same. Press the menu button to enter C.Fn ID, press the set button to choose OFF to turn off the wireless ID, or choose any figure from 01 to 99.
Scan the Spare Channel:
You can scan the spare channel to avoid the interference of using the same channel by others.
8.2 Positioning and Operation Range
The transmission distance between the transmitter unit and receiver unit is about 100m.

Figure 8.1: Wireless Flash Setup Example
Video 8.1: Godox V1 Pro Wireless Transmission and Reception Demonstration
9. Advanced Features
9.1 Modeling Lamp
Press the modeling lamp button to set the modeling lamp, press the set button to turn on or off the modeling lamp. When turning the modeling lamp on, turn the select dial to adjust its brightness in 10 levels (01~10).
9.2 Auto Focus Assist Beam
In poorly-lit or low-contrast shooting environments, the built-in auto focus assist beam will automatically light on to make it easier for autofocus. The beam will light up only when autofocus is difficult and get out as soon as the autofocus becomes correct.
9.3 Bounce Flash
By pointing the flash head toward a wall or ceiling, the flash will bounce off the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is called bounce flash.
9.4 ZOOM: Setting the Flash Coverage
The flash coverage can be set automatically or manually. It can be set to match the lens focal length from 28mm to 105mm. In auto zoom mode, the focal length changes in response to the camera's zoom lens to provide optimal flash results.
9.5 C.Fn: Setting Custom Functions
Press the menu button to enter C.Fn settings to customize various functions of the flash.
9.6 Control with the Camera's Menu
If the camera flash is attached to an EOS camera which has a camera control function, the flash can be controlled using the camera's menu screen. Refer to your camera's instruction manual for specific menu operations.
10. Protection Functions
10.1 Over-Temperature Protection
To avoid overheating and deteriorating the flash head, do not fire more than 100 continuous flashes in fast succession at 1/1 full power. After 100 continuous flashes, allow a rest time of at least 10 minutes.
If you fire more than 100 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycle time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal. When the over-temperature protection is started, <=> is shown on the LCD display.
11. Technical Data / Specifications
| Feature | Specification |
|---|---|
| Model | V1Pro C |
| Compatible Cameras | Canon EOS cameras (E-TTL II auto flash) |
| Power (1/1 output) | 76Ws |
| Flash Coverage | 28 to 105mm (Auto/Manual zoom) |
| Flash Duration | 1/300 to 1/20000 seconds |
| Exposure Control System | E-TTL II auto flash, manual flash |
| Flash Exposure Compensation (FEC) | Manual, FEB: ±3 steps with 1/3 increment each step |
| Flash Exposure Lock (FEL) | With <FEL> button or <*> button |
| Sync Mode | High-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync |
| Multi Flash | Provided (up to 100 times, 199Hz) |
| Wireless Flash (Radio 2.4G Transmission) Function | Transmitter, Receiver, Off |
| Wireless Transmitter Unit Groups | A, B, C, D |
| Wireless Controllable Receiver Groups | A, B, C, D, E (E group can be controlled by X series flash trigger) |
| Wireless Transmission Range (approx.) | 100m |
| Channels | 32 (01~32) |
| ID | OFF/01~99 |
| Modeling Flash | Fired with camera's depth-of-field preview button |
| Auto Focus Assist Beam Effective Range (approx.) | Center: 0.6~10m/2.0~32.8 feet, Periphery: 0.6~5m/2.0~16.4 feet |
| LED Modeling Lamp Power | 2w |
| LED Modeling Lamp Color Temperature | 3300K±200K |
| Power Supply | 7.2V/2980mAh Lithium Battery |
| Recycle Time | Approx. 1.3 seconds. Green LED indicator will light up when the flash is ready. |
| Number of Flashes at 1/1 step | Approx. 500 |
| Power Saving | Auto power off after approx. 90s of idle use (transmitter), 60min/30min (receiver) |
| Sync Triggering Mode | Hot shoe, 2.5mm sync cord |
| Dimension (WxHxD) | 156mm×76mm×124mm |
| Net Weight (Without Battery) | 466g |
| Net Weight (With Battery) | 580g |
12. Troubleshooting
If you encounter any problems with your Godox V1 Pro, refer to this troubleshooting guide:
The camera flash does not fire.
- The camera flash is not attached securely to the camera. → Attach the camera's mounting foot securely to the camera.
- The electrical contacts of the camera flash and camera are dirty. → Clean the contacts.
- <H> or <H> is not displayed in the view finder of camera. → Wait until the flash is fully recycled and the flash ready indicator lights up. If the flash ready indicator lights up, but <H> or <H> is not displayed in the view finder, check whether this flash unit is securely attached to the camera hot shoe.
- If the flash ready indicator does not light up after a long wait, check whether the battery power is enough. If the battery power is low, <=> will appear and blink on the LCD panel. Please replace the battery immediately.
The power turns off by itself.
- After 90 seconds of idle operation, auto power off took effect if the flash is set as a transmitter unit. → Press the shutter button halfway or press any flash button to wake up.
- After 60 minutes (or 30 minutes) of idle operation, the flash enters sleep mode if it is set as receiver unit. → Press any flash button to wake up.
Auto zoom does not work.
- The camera flash is not attached securely to the camera. → Attach the camera flash's mounting foot to the camera.
The flash exposure is underexposed or overexposed.
- There was a highly reflective object (e.g. glass window) in the picture. → Use FE lock (FEL).
- You used high-speed sync. → With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed.
- You used manual flash mode. → Set the flash mode to ETTL or modify the flash output.
Photos have dark corners or only parts of the target subject are illuminated.
- The focal length of lens exceeds the flash coverage. → Check the flash coverage you set. This flash unit has the flash coverage between 28 and 105mm, which fits medium-format cameras.
13. Firmware Upgrade
The Godox V1 Pro supports firmware upgrade through its USB-C port. Please use a USB-C cable (sold separately).
- Download and install the "Godox G3 firmware upgrade software" before upgrading.
- Choose the related firmware file.
- Refer to the latest electronic version of the instruction manual on the official Godox website for detailed instructions.
14. Compatible Camera Models
This flash unit can be used on the following Canon EOS series camera models:
- 1DX, 5D Mark III, 5D Mark II, 6D, 7D, 60D, 50D, 40D, 30D
- 650D, 600D, 550D, 500D, 450D, 400D Digital, 1100D, 1000D
- 5D Mark IV, 7D Mark II, 6D Mark II, 760D, 750D, 70D, 80D, 800D, 77D
- M5, M3, M50, EOS R, 1500D, 3000D, 5D II, 5D III, RP, 90D
Note: This table only lists the tested camera models, not all Canon EOS series cameras. For the compatibility of other camera models, a self-test is recommended. Rights to modify this table are retained.
15. Maintenance
- Shut down the device immediately should abnormal operation be detected.
- Avoid sudden impacts and the product should be dedusted regularly.
- It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary.
- Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
- This product, except consumables e.g. flash tube, is supported with a one-year warranty.
- Unauthorized service will void the warranty.
- If the product had failures or was wetted, do not use it until it is repaired by professionals.
- Changes made to the specifications or designs may not be reflected in this manual.
16. User Tips
- The Godox V1 Pro supports TTL (Through-The-Lens) metering for automatic flash exposure.
- High-Speed Sync (HSS) is supported, allowing flash synchronization speeds of up to 1/8000 seconds.
- For optimal battery life, store the lithium battery at approximately 50% charge and recharge it every six months.
17. Warranty & Support
Warranty Period: The warranty period for products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day (purchase date) when the product is bought for the first time. The purchase date is considered as the date registered on the warranty card when buying the product.
How to Get Maintenance Service: If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.
Inapplicable Cases: The guarantee and service offered by this document are not applicable in the following cases:
- The product or accessory has expired its warranty period.
- Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc.
- Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alteration, addition and detachment.
- The original identifying information of product or accessory is modified, altered, or removed.
- No valid warranty card.
- Breakage or damage caused by using illegally authorized, nonstandard or non-public released software.
- Breakage or damage caused by force majeure or accident.
- Breakage or damage that could not be attributed to the product itself.
For full warranty details and contact information, please refer to the official Godox website or the user manual PDF: Godox V1 Pro User Manual (PDF)