Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Electric Bicycle LCD 600C/500C NEW Bluetooth Display. This display is designed to enhance your e-bike riding experience by providing essential information and control over your Bafang mid/hub motor system.
Key features include a 2.4-inch IPS colorful screen, compatibility with 36V, 48V, 52V, and 60V systems, IP65 waterproof rating, and BF-UART communication protocol. The 600C Bluetooth version offers additional connectivity for navigation and call notifications.
Image: Front view of the 600C Bluetooth Display, showing the main interface and control buttons.
Setup
Compatibility Notes
- This display is only applicable to Bafang Mid/Hub Drive Motor Kits.
- Ensure your motor kit uses the BF-UART communication protocol. This display is not compatible with 5S-UART or CAN protocols.
- The display uses a 5-pin female circular connector.
- UART protocols can often be identified by the connector type: most 5-pin circular connectors use BF-UART, while male connectors typically use 5S-UART. CAN protocol uses triangular connectors.
Installation Instructions
- Install the display unit and its button control module securely on your e-bike handlebar.
- Adjust the location for optimal visibility and ergonomic access to the buttons.
- Ensure the e-bike power is OFF before connecting the display.
- Plug the display's 5-pin female circular connector into the corresponding port on your e-bike controller.
Image: The display unit installed on an e-bike handlebar, showing its position relative to other controls.
Image: Technical drawing illustrating the dimensions of the display (82.4mm x 49.8mm) and the 22.2mm holder diameter.
Operating Instructions
Basic Functions
- Power On/Off: Press and hold the power button (usually 'M' or 'I/O') to turn the display on or off.
- Headlights: Long press the '+' button to turn the headlights on or off.
- 6KM/Walk Mode: Long press the '-' button to activate the 6KM/Walk mode.
- Assist Level: Use the '+' and '-' buttons to adjust the pedal assist level (0-3, 0-5, or 0-9, depending on configuration).
Display Modes and Interfaces
The 600C display offers multiple interfaces, which can be switched by the user. The '600C Sports Version' includes additional sports model functions.
Image: Comparison of the display in 'Digital mode' and 'Analog mode'.
Classics Mode Interface
Image: Detailed view of the 'Classics mode' display, labeling various indicators.
- Power: Current power output in watts (e.g., 689W).
- Speed Indication: Bar graph showing speed level (H, M, L).
- Power Indication: Bar graph showing power output.
- Head Light: Indicator for active headlights.
- Brake: Brake activation indicator.
- Clock: Current time (e.g., 02:38).
- Battery Voltage: Current battery voltage (e.g., 52.0V).
- Battery Indication: Graphical representation of battery charge level.
- Speed Value: Current speed in Km/H (e.g., 25 Km/H).
- ODO/Trip/Time: Displays Odometer, Trip distance, or Trip time.
- Assist Level: Current pedal assist level (e.g., 1).
- LOGO/Error: Displays the product logo or error codes.
Bluetooth Page Interface (600C Bluetooth Version Only)
Image: The display showing navigation instructions, integrated with a smartphone app's navigation interface.
- Battery: Current battery voltage (e.g., 52.0V).
- Distance to next junction: (e.g., 38 M).
- Bluetooth: Bluetooth connection status.
- Remaining time of riding: Estimated time remaining for the current ride (e.g., 13 MIN).
- Warning of low battery power: Indicator for low battery.
- Navigation indication: Visual cues for navigation (e.g., turn arrow).
- Riding mileage: Current riding distance (e.g., 99.9 KM).
- Brake: Brake activation indicator.
- Speed Value: Current speed in Km/H.
- Bluetooth pairing key: (e.g., 555555).
- Assist Level: Current pedal assist level.
- Call: Incoming call notification (e.g., 18901538741).
- Head Light: Indicator for active headlights.
Settings
- Default Password: 1919
- Default Speed Limits: 99 KM/H
- Assist Levels: Configurable for 3, 5, or 9 levels.
Maintenance
- To ensure water-resistant performance, protect the display's membrane from damage.
- Clean the display screen with a soft, damp cloth. Avoid abrasive cleaners or solvents.
- Regularly check the connector for any signs of corrosion or damage.
Troubleshooting
- Display not turning on: Ensure the power to the unit is off before plugging or unplugging the display. Check all connections.
- Display malfunction: Do not attempt to reset parameters if the display is not working correctly. Contact customer service for assistance.
- Physical damage: Avoid collisions and impacts to prevent damage to the display.
- Error Codes: The display may show error codes in the 'LOGO/Error' section. Refer to your motor kit's manual or contact support for specific error code interpretations.
Specifications
| Feature | Specification |
|---|---|
| Product Type | TFT LCD Display |
| Display Name | 600C / 500C NEW |
| Screen Size | 2.4 inch IPS colorful screen |
| Compatible With | Bafang Motor Kits |
| Shell Material | ABS |
| Screen Material | High Strength Acrylic |
| Dimensions (Host) | 80mm * 41mm |
| Holder Diameter | 22.2 mm |
| Rated Operating Current | 40mA |
| Max Operation Current | 100mA |
| Display Voltage | 24V/36V/48V/52V/60V |
| Communication Protocol | BF-UART |
| Display Connector | 5 Pin Female Circular Connector |
| Operating Temperature | -30°C to 80°C |
| Waterproof Rating | IP 65 |
| Speed Mode Options | 0-3 / 0-5 / 0-9 |
| Default Password | 1919 |
| Default Speed Limits | 99 KM/H |
| Indicators | Battery, Mileage, Power, Current, Error, Lamp, Speed (AVG, MAX, Real-time) |
| Origin | Mainland China |
User Tips
- All versions of the 600C display have two interfaces that can be changed by the user. Experiment to find your preferred layout.
- If you ordered the '600C Bluetooth' version, remember to utilize the Bluetooth function for navigation and call notifications via the 'I-Bike' app. The standard '600C' model does not include Bluetooth.
- The display comes with a double-layer protective cover. Removing the outer layer will reveal a pristine screen underneath.
- Always ensure the e-bike's power is off before connecting or disconnecting the display to prevent potential damage.
Frequently Asked Questions (FAQ)
- Q: Is this display compatible with non-Bafang motors?
- A: No, this display is specifically designed for Bafang Mid/Hub Drive Motor Kits.
- Q: What communication protocol does this display use?
- A: It uses the BF-UART protocol. It is not compatible with other UART protocols like 5S-UART or CAN protocols.
- Q: What type of connector does it have?
- A: The display features a 5-pin female circular connector.
- Q: Can I change the display interface?
- A: Yes, all 600C versions offer two different display interfaces that you can switch between.
- Q: Does the standard '600C' model have Bluetooth functionality?
- A: Only the '600C Bluetooth' version includes Bluetooth functionality. The regular '600C' model does not.
- Q: Can this display replace KD58C or KD21C displays?
- A: Compatibility depends on the communication protocol and connector type of your existing system. This display uses BF-UART protocol and a 5-pin female circular connector. If your current display uses a different protocol or connector, it will not be compatible.
Warranty and Support
Warranty Agreement
The Electric Bicycle LCD 600C/500C NEW Display, as an accessory, comes with a 12-month warranty period from the date of receipt. This warranty covers manufacturing defects and malfunctions under normal use. It does not cover physical damage or issues arising from incorrect operation.
For other components:
- Motor Kits: 12-month warranty, excluding physical damage and wrong operation.
- Battery: 12-month warranty, excluding physical damage and wrong operation.
Customer Support
If you encounter any problems or have questions regarding your display, please contact the seller or manufacturer's customer service. Provide your product model and a detailed description of the issue for prompt assistance.
