OBDOK Renolink V2.10

Contents

Renolink V2.10 OBD2 Diagnostic Interface User Manual

1. Introduction

The Renolink V2.10 is a professional diagnostic and programming device designed for electronic control units (ECUs) in Renault and Dacia vehicles, including recently produced models. This device offers a wide range of functionalities for vehicle maintenance and repair.

Important Note: Renolink V2.10 software is compatible only with Windows 10 and Windows 11 operating systems. Each software installation requires activation, and one activation is limited to a single computer. If you change your computer, a new software license must be purchased.

Renolink V2.10 device with software interface screenshots
Figure 1: Renolink V2.10 Diagnostic Interface and Software Overview

2. Key Features and Capabilities

The Renolink V2.10 offers extensive capabilities for various vehicle systems:

  • Eprom Read/Write
  • ECU Resetting
  • Clear Crash Airbag (e.g., in v1.98 for Dacia Logan3, Sandero3, Renault Clio5, Km in ABS ATE for Megane3, Scenic3 with 2 clicks)
  • Airbag Reset
  • Airbag Virginize
  • Key Programming
  • TDB (Cluster) Programming and Kilometer Modification
  • Indicator Programming
  • ECM Programming
  • UCH Programming
  • EPS Virginizer
  • EPS Resetting
  • ECM Read/Write Flash
  • UCH Cleaner - Read PIN UCH T4
  • Key Programming for Dacia Duster Docker Logan (new models)
  • Card Programming for Laguna 3 / Megane 3 in protected mode
  • Decoding Direction Assisted (DAE) - Power Steering for Renault Megane 4 and Megane 4 ph2 & Clioo 5

Recent updates include:

  • ECU learning for DACIA Logan 2 / Sandero / Lodgy / Docker / Duster ph2 (addresses known issues with ECM V42)
  • Read/Write eeprom and flash for dashboard Dacia Logan2 / Sandero2 / Lodgy / Docker / Duster ph2 (2013-2014 and 2014-2017 models)
  • Read/Write flash, eeprom, and kilometer for dashboard (VDO) Megane 3 and Fluence 2015+
  • Read/Write flash, eeprom, and kilometer for Laguna 3 dashboard
  • Read/Write kilometer, eeprom, and flash for dashboard Renault Fluence
  • Key programming for UCH BMT Sagem for Dacia Solenza, Dacia Supernova, Renault Twingo, Renault Kangoo, Renault Master (1998-2003)
  • Read/Write kilometer for dashboard Renault Modus
  • Read/Write kilometer and eeprom for dashboard Koleos
  • Key programming for Dacia Logan 2, Sandero 2, Duster ph 2, Lodgy, Dokker, and Renault Clio Symbol 3

3. Setup and Installation

Follow these steps to set up your Renolink V2.10 device and software:

  1. Hardware Connection: Connect the Renolink V2.10 device to your computer via the USB cable. Then, connect the OBD2 end of the device to your vehicle's OBD2 port.
  2. Software Installation: Install the Renolink V2.10 software on your Windows 10 or Windows 11 computer. Ensure you have administrative privileges during installation.
  3. Software Activation: The software requires activation. Follow the on-screen prompts or instructions provided with your purchase to activate the software. Remember, one activation is for one computer.
  4. Driver Installation: Ensure all necessary drivers for the Renolink device are installed correctly. These are typically included with the software package or can be downloaded from the manufacturer's website.
  5. Initial Software Launch: Launch the Renolink software. You may encounter a warning regarding the 'Latency Timer' for optimal performance. Click 'OK' to proceed.
  6. Select Scan Option: In the software interface, navigate to the 'Scan' menu.
  7. Choose ECU Type: From the 'Scan Ecu Option' dropdown menu, select the specific ECU you wish to scan (e.g., 'ECM' for Engine Control Module).
  8. Initiate Scan: Click the 'Scan' button to begin the diagnostic scan of the selected ECU.
Renolink software scan window showing ECU selection
Figure 2: Renolink Software Scan Window with ECU Selection
Top-down view of the red Renolink OBD2 diagnostic cable
Figure 3: Renolink OBD2 Diagnostic Cable
Close-up of the USB connector end of the Renolink cable
Figure 4: USB Connector
Close-up of the OBD2 connector end of the Renolink cable
Figure 5: OBD2 Connector

4. Operating Instructions

Once the device is connected and the software is running, you can perform various diagnostic and programming tasks. The software interface is organized into different screens and functions.

4.1. General Diagnostic Scan

  1. Ensure the Renolink device is connected to both your computer and the vehicle's OBD2 port.
  2. Open the Renolink software.
  3. Click on the 'Scan' menu item.
  4. In the 'Scan' window, select 'All' for 'Scan Protocol Option' and choose the specific ECU (e.g., 'ECM', 'Airbag', 'UCH') from the 'Scan Ecu Option' dropdown.
  5. Click 'Scan' to initiate the process. The software will display detected ECUs and their details.
  6. Once scanning is complete, click 'Close' to exit the scan window.
Video 1: Renolink Software Demonstration - Shows the process of opening the software, acknowledging a warning, initiating an ECU scan, and navigating through various parameter screens.

4.2. Accessing ECU Parameters

After connecting to an ECU, you can access various screens to view and modify parameters:

  • Screens Panel: On the left side of the software, a 'Screens' panel lists available functions and data frames (Trame).
  • Engine Parameters (Moteur): Select 'Banc_Moteur' or 'Trame 01 Paramètres généraux' to view real-time engine data such as engine speed, pressure, temperature, and voltage.
  • Throttle Pedal Parameters (Pédale-Papillon): Select 'Trame 03 Papillon-Pédale' to monitor throttle pedal positions, values, and detect any related faults.
  • Identification: Select 'Identification' to view ECU identification details like Renault Calculator number, Diagnostic number, Hardware version, Software version, and Calibration information.
  • Other Data Frames: Explore other 'Trame' options like 'Trame 02 Etats et Paramètres secondaires' (Secondary States and Parameters), 'Trame 04 Adaptatif de richesse' (Richness Adaptations), 'Trame 05 Ralenti et VVT' (Idle and VVT), 'Trame 06 Structure Couple' (Torque Structure), 'Trame 07 OBD', 'Trame 08 Usure', 'Trame 09 Détrompage' (Detuning), 'Trame 10 Paramètres Etudes' (Study Parameters), 'Trame 11 Throttle Area Curve', 'Trame 30 FTDIV', 'Trame 31 CLIM', 'Trame 32 VSC', 'Trame 33 RVLV' for specific vehicle data and functions.
Renolink software displaying engine and throttle pedal parameters
Figure 6: Engine and Throttle Pedal Parameters Screen
Renolink software displaying general parameters
Figure 7: General Parameters Screen
Renolink software displaying routine execution and memory access options
Figure 8: Routine Execution and Memory Access Options

5. Maintenance

To ensure the longevity and optimal performance of your Renolink V2.10 device:

  • Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
  • Avoid exposing the device to moisture or liquids.
  • Handle the cables and connectors with care to prevent damage.

6. Troubleshooting

If you encounter issues with your Renolink V2.10, consider the following:

  • Software Not Launching/Connecting:
    • Ensure your operating system is Windows 10 or Windows 11.
    • Verify that the software has been properly activated for your computer.
    • Check if the device drivers are correctly installed.
    • Restart your computer and try again.
  • Device Not Detected:
    • Ensure the USB cable is securely connected to both the device and the computer.
    • Try a different USB port on your computer.
    • Check the vehicle's OBD2 port for power and proper connection.
  • Latency Timer Warning: If you receive a warning about 'Latency Timer' for best performance, consult your computer's device manager settings for the serial port to adjust the latency timer to 1 ms if possible.
  • Communication Errors:
    • Ensure the vehicle's ignition is on (or engine running, as required by the specific function).
    • Verify that the correct ECU type is selected in the software's scan options.
    • Check for any loose connections in the OBD2 or USB cables.

7. Specifications

AttributeValue
Brand NameOBDOK
Model Namerenolink v2.10
Software Versionrenolink v2.10
Hardware Versionnew / Renolink OBD2
Item TypeAuto Key Programmer
Item FunctionECU Programmer
Car MakesFor Renault
OriginMainland China
External Testing Certificationce
Voltagev
PowerW
Item Weight0.2kg
Item Height10cm
Item Width15cm
Item Length25cm
Package Length25cm
Package Width12cm
Package Height10cm
Wireless SupportNo
ElectronicNo
Batteries Includedno

8. User Tips

  • When performing UCH matching or other sensitive programming, always ensure the vehicle's battery is fully charged to prevent interruptions.
  • For optimal performance, ensure your computer's Latency Timer for the serial port is set to 1 ms, as suggested by the software.
  • Always back up existing ECU data before performing any write operations to prevent data loss.

9. Warranty and Support

For detailed information regarding warranty, technical support, or any other inquiries, please refer to the official user manual PDF available at User Manual (PDF). You may also contact the seller or manufacturer directly for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.