1. Product Overview
The MS48-LR is an open-source LoRaWAN To Modbus Gateway designed to bridge LoRa wireless networks to IP networks. It supports connectivity via WiFi, Ethernet, or an optional 4G Cellular Network. This gateway enables users to send data over extremely long ranges at low data rates, making it ideal for various IoT applications.
Fully compatible with the LoRaWAN protocol, the MS48-LR integrates a built-in LoRaWAN Server and IoT server. This allows users to connect numerous LoRaWAN devices to the gateway and access them through a Modbus network using a PLC (Programmable Logic Controller).
The MS48-LR comes pre-configured with various LoRaWAN frequency bands to suit different countries, with options for users to customize these bands for their specific LoRa network requirements. It also supports remote management, simplifying monitoring and maintenance for system integrators.
2. Key Features
- Open Source Debian system
- Managed via Web GUI, SSH over LAN or WiFi
- 10 programmable parallel demodulation paths
- Pre-configured to support different LoRaWAN regional settings
- Auto-calibrating LoRaWAN regional parameters
- Supports various LoRaWAN Connections: Semtech UDP Packet Forwarder, LoRaWAN Basic Station, ChirpStack Gateway Bridge (MQTT)
- Remote Monitoring capabilities
- Auto-provisioning for batch deployment and management
- Functions as a LoRaWAN Gateway
- Built-in ChirpStack local LoRaWAN server
- Built-in Node-Red local Application server
- Can act as Modbus Slave mode
3. Technical Specifications
3.1. Hardware System
- CPU: Quad-core Cortex-A7 1.2Ghz
- RAM: 512MB
- eMMC: 4GB
3.2. Interface
- Ethernet: 1 x 10M/100M RJ45 Port
- Wireless: Multi-Channel LoRaWAN Wireless, WiFi 802.11 b/g/n
- USB: 1 x USB 2.0 Host Connector
- Expansion: 1 x Mini-PCI E Connector
- Serial: 1 x RS485 Interface, 1 x RS232 Interface
3.3. LoRa Specifications
- Sensitivity: Up to -140 dBm with SX1250 Tx/Rx front-end
- Interferer Rejection: 70 dB CW interferer rejection at 1 MHz offset
- SNR Operation: Able to operate with negative SNR, CCR up to 9dB
- Demodulators: Emulates 49 x LoRa demodulators and 1 x (G)FSK demodulator
- Radio Interfaces: Dual digital TX & RX radio front-end interfaces
- Demodulation Paths: 10 programmable parallel demodulation paths
- Data Rate: Dynamic data-rate (DDR) adaptation
- Antenna: True antenna diversity or simultaneous dual-band operation
3.4. Cellular 4G LTE (Optional)
- Module: Quectel EC25 LTE module
- SIM: Standard Size SIM Slot
- Antennas: 2 x 4G Sticker Antennas
- Data Rates: Up to 150Mbps downlink and 50Mbps uplink
- Coverage: Worldwide LTE, UMTS/HSPA+, and GSM/GPRS/EDGE
- Technology: MIMO technology for enhanced data rate and link reliability
3.5. Operating Conditions
- Work Temperature: -20 ~ 70°C
- Storage Temperature: -20 ~ 70°C
- Power Input: 12V, 2A, DC
4. Package Contents
The standard package for the MS48-LR LoRaWAN To Modbus Gateway typically includes:
- 1x Dragino MS48-LR LoRaWAN To Modbus Gateway
- 2x LoRa Antennas
- 1x Power Adapter (EU/US/UK/AU plug, depending on selection)
- (Optional) 2x 4G Cellular Antennas (if 4G module is included)
Dimensions and Weight:
- Length: 23 cm
- Width: 13 cm
- Height: 6 cm
- Weight: 0.55 kg
5. Setup Guide
5.1. Physical Installation
- Attach Antennas: Carefully screw the provided LoRa antennas onto the corresponding connectors on the gateway. If your model includes a 4G module, attach the cellular antennas as well.
-
Insert SIM Card (for 4G models): If your MS48-LR includes a 4G cellular module, locate the standard size SIM slot on the side of the device. Insert your activated SIM card into the slot, ensuring correct orientation.
Figure 2: Side view with Wireless, Cellular, and SIM Slot -
Connect Ethernet (Optional): For wired network connectivity, connect an Ethernet cable from your router or network switch to the RJ45 port on the gateway.
Figure 3: Rear view with Ethernet and Power Ports -
Connect Power: Connect the provided 12V DC power adapter to the DC power input port on the gateway, then plug the adapter into a power outlet. The device will power on automatically.
Figure 4: Front view with LED Indicators and Serial Ports
5.2. Initial Configuration
The MS48-LR can be configured via its Web GUI or SSH. Refer to the official Dragino documentation for detailed instructions on accessing the Web GUI and performing initial network and LoRaWAN server setup. This typically involves:
- Connecting to the gateway's default WiFi hotspot or via Ethernet.
- Accessing the Web GUI through a web browser (e.g.,
http://192.168.1.1). - Configuring network settings (static IP, DHCP, WiFi client mode, 4G settings).
- Setting up the built-in LoRaWAN server (ChirpStack) and IoT server (Node-RED).
- Adjusting LoRaWAN regional parameters if necessary.
6. Operation Guide
6.1. LoRaWAN Network Operation
Once configured, the MS48-LR acts as a LoRaWAN gateway, receiving data from LoRaWAN end-devices and forwarding it to the built-in LoRaWAN server. The server then processes this data and makes it available to the integrated IoT server (Node-RED) or other connected applications.
- Ensure your LoRaWAN end-devices are correctly provisioned and configured to communicate with the gateway's frequency plan.
- Monitor device connectivity and data flow through the LoRaWAN server interface.
6.2. Modbus Integration
The MS48-LR can operate in Modbus Slave mode, allowing PLCs or other Modbus Masters to read data from connected LoRaWAN devices. This integration facilitates seamless data exchange between LoRaWAN sensors and industrial control systems.
- Configure the Modbus settings within the gateway's interface, including Modbus ID and data mapping.
- Connect your Modbus Master device (e.g., PLC) to the RS485 or RS232 interface of the MS48-LR.
- Refer to the Modbus documentation for the MS48-LR for specific register addresses and data formats.
6.3. Remote Management
The gateway supports remote management, enabling system integrators to monitor and maintain the device from a remote location. This feature is crucial for large-scale deployments and ensures continuous operation.
- Access the Web GUI or SSH remotely using the gateway's public IP address or through a VPN connection.
- Regularly check system logs and performance metrics.
7. Maintenance
- Firmware Updates: Regularly check the Dragino website for firmware updates to ensure optimal performance, security, and access to new features. Follow the provided instructions for safe firmware upgrades.
- Physical Cleaning: Keep the gateway clean and free from dust. Use a soft, dry cloth for cleaning. Ensure ventilation holes are not obstructed.
- Environmental Conditions: Operate the device within the specified temperature range (-20 ~ 70°C) and avoid exposure to extreme humidity or direct sunlight.
- Cable Connections: Periodically check all cable connections (power, Ethernet, antennas) to ensure they are secure.
8. Troubleshooting
8.1. Power Issues
- No Power Indicator: Ensure the 12V DC power adapter is correctly connected to the gateway and a working power outlet. Check the power adapter for damage.
8.2. Network Connectivity Issues
- No Ethernet Connection: Verify the Ethernet cable is securely connected to both the gateway and your network device. Check your router/switch for port status.
- No WiFi Connection: Ensure the WiFi antennas are properly attached. Check the gateway's WiFi settings in the Web GUI.
- No 4G Cellular Connection: Ensure the SIM card is correctly inserted and activated. Verify the 4G antennas are attached. Check the 4G module status in the Web GUI.
- Cannot Access Web GUI: Ensure your computer is on the same network as the gateway. Try pinging the gateway's IP address. Clear your browser cache or try a different browser.
8.3. LoRaWAN Connectivity Issues
- No Data from End-Devices: Check LoRa antenna connections. Verify that the end-devices are within range and configured with the correct frequency band and LoRaWAN parameters. Check the LoRaWAN server logs for incoming packets.
- LoRaWAN Server Not Running: Access the gateway via SSH or Web GUI and check the status of the ChirpStack LoRaWAN server. Restart the service if necessary.
8.4. Modbus Communication Issues
- No Modbus Communication: Verify the physical connection to the RS485/RS232 port. Ensure Modbus settings (baud rate, parity, slave ID) on the gateway match those of the Modbus Master. Check Modbus data mapping.
9. Warranty and Support
For warranty information, technical support, and further documentation, please refer to the official DRAGINO website or contact your vendor. Keep your purchase receipt for warranty claims.