Flipsky VX3 Pro

Contents

Flipsky VX3 Pro Wireless Remote Controller User Manual

Model: VX3 Pro | Brand: Flipsky

1. Introduction

The Flipsky VX3 Pro is a state-of-the-art 2.4G wireless remote controller engineered for high-performance electric water sports and skateboarding applications, including Efoil, Esurf, and ESK8. This manual provides essential information for the safe and effective operation, setup, and maintenance of your VX3 Pro controller.

Front view of the Flipsky VX3 Pro remote controller
Figure 1: Front view of the Flipsky VX3 Pro remote controller.

2. Key Features

  • 1.8-inch Super Clear Display: Provides comprehensive telemetry data.
  • Advanced Telemetry: Displays GPS, motor power, real-time MOS tube temperature, and throttle progress bar.
  • Broad Compatibility: Compatible with Flipsky FSESC/FTESC and other VESC and Non-VESC systems.
  • Dual Mode Operation: Seamless switching between ESK8 (Electric Skateboard) and E-surf (Electric Surfboard) modes.
  • Cruise Control: Dedicated cruise speed control function for E-surf mode.
  • High Waterproof Rating: IP67 for reliable performance in wet conditions.
  • Extended Battery Life: Equipped with a 1500mAh remote battery.
  • ESC Failure Reporting: Detects and reports potential ESC failures for timely replacement.
  • Flexible Control Modes: Supports PPM and UART controller modes.
  • Convenient Charging: Features wireless magnetic charging.
  • Integrated Receiver: VX3 Pro Remote includes a receiver (supports Flipsky non-VESC).
  • Firmware Upgradable: Supports online firmware upgrades.
  • Enhanced Communication: Utilizes SX1280 communication module.
  • Improved Microcontroller: Features GD32F303CGT6 transmitter microcontroller.
  • FTESC ESC UART Protocol: Added support for FTESC ESC UART control protocol.
  • Multiple Control Options: Supports UART, PPM, and UART&PPM control modes.
  • Intuitive Function Switching: Joystick-based up and down switching control.
  • Gear Lock Function: For added safety and control.
  • Low Battery Alarm: Alerts for low battery levels on both skateboards and surfboards.
  • Total Mileage Display: Tracks total distance traveled.
  • Customizable Settings: Adjustable wheel diameter (up to 999mm) and default startup gear.
  • Configurable Cruise/Reverse: Option to enable/disable cruise mode and reverse function.
  • Optimized Performance: Faster screen refresh rate and data display.

3. Specifications

Attribute Detail
Display Screen 1.8-inch, Super Clear
Telemetry Data GPS, Motor Power, MOS Tube Temp, Throttle Progress, Real-time Speed, Single Mileage, ESC Real-time Current, ESC Temperature, Putter Throttle Percentage
Compatibility Flipsky FSESC/FTESC, VESC, Non-VESC
Operating Modes ESK8, E-surf (with Cruise Control)
Waterproof Rating IP67
Remote Battery Capacity 1500mAh
Controller Modes PPM, UART, UART&PPM
Charging Method Wireless Magnetic Charging
Communication Module SX1280
Transmitter Microcontroller GD32F303CGT6
Material Plastic
Batteries Included Yes
Recommended Age 14+ years
Certification CE, RoHS
Origin Mainland China

4. Package Contents

The VX3 Pro controller package typically includes the following items:

  • Flipsky VX3 Pro Remote Controller
  • Receiver Module
  • Wireless Magnetic Charging Pad
  • USB Charging Cable
  • Receiver Connection Cables (PPM/UART)
  • Wrist Strap
  • Carrying Case
Image showing the complete package contents of the Flipsky VX3 Pro remote controller, including the remote, receiver, charging pad, cables, and wrist strap in a carrying case.
Figure 2: Contents of the VX3 Pro package.

5. Setup Guide

5.1 Remote Controller Overview

Familiarize yourself with the buttons and display on your VX3 Pro remote controller:

Top-down view of the Flipsky VX3 Pro remote controller, showing the 1.8-inch display screen and control buttons.
Figure 3: Top-down view of the VX3 Pro remote controller with display.
Diagram illustrating the components of the VX3 Pro remote and receiver. The remote shows a 1.8-inch display screen, brake trigger, throttle trigger, power on/off button, setting button, charging sign, and hang strap. The receiver shows PPM1, PPM2, V5, GND, VTX1, VTX2, VRX1, VRX2, BAT+ pins, blue indicator light, and red indicator light.
Figure 4: VX3 Pro Remote and Receiver Components labeled.
  • 1.8-inch Display Screen: Shows telemetry data.
  • Brake Trigger: Controls braking.
  • Throttle Trigger: Controls acceleration.
  • Power On/Off Button: Turns the remote on or off.
  • Setting Button: Accesses menu and settings.
  • Charging Sign: Indicates charging status.
  • Hang Strap: For securing the remote.

5.2 Receiver Wiring

The VX3 Pro receiver supports both UART and PPM control modes. Choose the appropriate wiring based on your ESC (Electronic Speed Controller).

5.2.1 UART Control Mode

UART control mode supports one-key reverse function and data display, applicable for ESCs based on VESC and FTESC controllers.

Wiring diagram for UART control mode. The receiver pins BAT+, VRX2, VTX2, VRX1, VTX1, GND, 5V, PPM1, PPM2 are shown connected to VESC RX, VESC TX, VESC GND, VESC 5V. This mode supports one-key reverse and data display for VESC/FTESC.
Figure 5: UART Control Mode Wiring Diagram.

Connect the receiver to your VESC/FTESC as follows:

  • Receiver VTX1 to VESC RX
  • Receiver VRX1 to VESC TX
  • Receiver GND to VESC GND
  • Receiver 5V to VESC 5V
  • BAT+ for battery level detection (optional, connect to main battery positive)

5.2.2 PPM Control Mode

PPM control mode operates without positive and reverse switching functions and is applicable to all ESCs.

Wiring diagram for PPM control mode. The receiver pins BAT+, VRX2, VTX2, VRX1, VTX1, GND, 5V, PPM1, PPM2 are shown. PPM1 or PPM2 can be connected to the ESC. This mode is without positive and reverse switching function.
Figure 6: PPM Control Mode Wiring Diagram.

Connect the receiver to your ESC using either PPM1 or PPM2:

  • Connect Receiver PPM1 or PPM2 to the corresponding PPM input on your ESC.
  • Connect Receiver GND to ESC GND.
  • Connect Receiver 5V to ESC 5V.
  • BAT+ for battery level detection (optional, connect to main battery positive).

For more detailed wiring, refer to the comprehensive diagram below:

Detailed wiring diagram showing connections for both UART and PPM modes, including battery level detection line and VESC connections. It illustrates how to connect the receiver to a VESC for UART control and to a generic ESC for PPM control, with options for battery voltage sensing.
Figure 7: Comprehensive Receiver Wiring Diagram.

5.3 Initial Pairing

Typically, the remote and receiver come pre-paired. If re-pairing is necessary, consult the Flipsky support resources for specific instructions.

6. Operating Instructions

6.1 Power On/Off

Press and hold the Power On/Off button on the remote to turn it on or off.

6.2 Screen Display Introduction (ESK8 Mode)

The 1.8-inch display provides real-time information. Below is an overview of the display in ESK8 mode:

Diagram of the VX3 Pro remote screen display in ESK8 mode. It shows indicators for UART mode, remote battery, Esk8 battery, receiver signal, speed mode (H/M/L), motor steering, real-time speed (km/h or mph), single mileage, ESC real-time current, ESC temperature, and putter throttle percentage.
Figure 8: ESK8 Mode Screen Display Introduction.
  • UART mode: Indicates communication protocol.
  • Remote battery: Remote controller battery level.
  • Esk8 battery: Electric skateboard battery level.
  • Receiver signal: Strength of the wireless connection.
  • Speed mode (H/M/L): High, Medium, or Low speed setting.
  • Motor steering: Direction of motor rotation.
  • Real-time speed: Current speed in km/h or mph.
  • Single mileage: Distance traveled in the current session.
  • ESC real-time current: Current draw from the ESC.
  • ESC temperature: Real-time temperature of the ESC.
  • Putter throttle percentage: Current throttle input.

6.3 Mode Switching (ESK8 / E-surf)

The remote allows free switching between ESK8 and E-surf modes. Use the joystick (up and down switching control) to navigate through the menu and select your desired mode. Refer to the remote's on-screen menu for specific navigation.

6.4 Cruise Speed Control (E-surf Mode)

In E-surf mode, the cruise speed control function can be activated. Consult the remote's menu settings to enable and adjust this feature.

6.5 Gear Lock Function

The gear lock function provides an additional layer of control. Activate and manage this feature through the remote's settings menu.

6.6 Customizing Settings

Access the settings menu using the Setting Button to adjust various parameters:

  • Wheel Diameter: Can be set up to 999mm for accurate speed and mileage readings.
  • Default Gear: Modify the default gear at startup.
  • Cruise Mode/Reverse Function: Enable or disable these functions as needed.

7. Maintenance

7.1 Charging the Remote

The VX3 Pro remote features wireless magnetic charging. Place the remote on the provided charging pad to initiate charging. Ensure the charging sign on the remote indicates proper connection.

7.2 Waterproof Care

With an IP67 waterproof rating, the remote is protected against immersion in water up to 1 meter for 30 minutes. However, it is recommended to rinse the remote with fresh water after use in saltwater environments and ensure it is dry before charging or storing.

7.3 Firmware Updates

The remote supports online firmware upgrades. Periodically check the Flipsky official website or app for the latest firmware versions to ensure optimal performance and access to new features. Follow the provided instructions carefully during the upgrade process.

8. Troubleshooting

  • ESC Failure Report: The remote can detect and report possible failures of the ESC. If an ESC failure is reported, immediately cease operation and inspect your ESC for issues. Consult your ESC's manual or Flipsky support for diagnostic steps.
  • Low Battery Alarm: The remote will provide a low battery alarm for both the remote itself and the connected skateboard/surfboard battery. Ensure both are adequately charged before use.
  • No Display/Unresponsive: Ensure the remote is charged. Try restarting the remote. If issues persist, contact support.
  • Connectivity Issues: Ensure the receiver is correctly wired and powered. Re-attempt pairing if necessary. Check for obstructions or interference.

9. User Tips

  • Compatibility Check: While the VX3 Pro is broadly compatible with VESC and Non-VESC systems, always verify compatibility with your specific Efoil or Esurf model (e.g., Takuma) before extensive use.
  • Regular Firmware Updates: Keep your remote's firmware updated to benefit from performance improvements and new features.
  • Secure Attachment: Always use the provided wrist strap to prevent accidental drops, especially during water sports.
  • Battery Management: Pay attention to the low battery alarms for both the remote and your vehicle to avoid unexpected power loss during operation.

10. Safety Warnings

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always operate your electric skateboard or surfboard responsibly and in accordance with local laws and regulations. Wear appropriate safety gear, including helmets and protective clothing, when operating any electric vehicle.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact Flipsky customer service or visit their official website. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.