1. Introduction
1.1 Vehicle Coverage
This diagnostic device is specifically designed to work with all OBD II compliant vehicles, including Controller Area Network (CAN). The EPA requires that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant, and this includes all American, Asian, and European vehicles.
A small number of gasoline vehicles from model years 1994 and 1995 are OBD II compliant. To check if a 1994 or 1995 vehicle is OBD II compliant, check the following:
- Vehicle Emission Control Information (VECI) Label: This label is located under the hood or on the radiator of most vehicles. If the vehicle is OBD II compliant, the label will state "OBD II Certified."
- 16-Pin Data Link Connector (DLC): Legal regulations require that all OBD II compliant vehicles must have a "common" 16-pin Data Link Connector (DLC).
Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only vehicles with a Vehicle Emission Control Information label stating "OBD II Certified" are OBD II compliant.
1.2 On-Board Diagnostics (OBD) II
The OBD II system is designed to monitor emission control systems and key engine components by performing continuous or periodic tests of specific components and vehicle conditions, providing three valuable pieces of information:
- Whether the Malfunction Indicator Lamp (MIL) is on or off;
- Which Diagnostic Trouble Codes (DTCs) are stored, if any;
- Status of readiness monitors.
1.3 OBD II Definitions
The following terms and their definitions relate to OBD II systems. Refer to this list as needed to aid in understanding OBD II systems.
- EOBD: European On-Board Diagnostics. Essentially the same as OBD II, with the same Data Link Connector and communication protocols.
- Communication Protocols: Enables communication between various systems and sensors in a vehicle. Currently, there are five protocols: CAN-Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
- PCM (Powertrain Control Module): The PCM is the OBD II accepted term for the vehicle's "on-board computer." In addition to controlling engine management and emission systems, the PCM is also involved in controlling powertrain operation (transmission). Most PCMs can also communicate with other vehicle computers (ABS, transmission control, body, etc.).
- DLC (Data Link Connector): The 16-pin connector on the vehicle that allows communication between the computer system and the diagnostic device.
- MIL (Malfunction Indicator Lamp): The vehicle's "Check Engine" warning light, which illuminates when a DTC is stored.
- DTC (Diagnostic Trouble Code): A code stored in the computer system's memory that helps identify the fault condition causing the MIL to activate.
- Freeze Frame Data: Operating conditions stored when a DTC is recorded.
- PID (Parameter Identification Data): Data returned by the vehicle's control modules to the diagnostic device.
- Monitors: "Diagnostic routines" programmed into the PCM. The PCM uses these programs to perform diagnostic tests and monitor the operation of emission-related components or systems of the vehicle to ensure they function correctly and within manufacturer specifications.
- Enabling Criteria: Also called activation conditions. These are vehicle-specific events or conditions that must occur within the engine before the various monitors are set or run. Some monitors require the vehicle to follow a prescribed "drive cycle" routine as part of the enabling criteria. Drive cycles vary between vehicles and for each monitor in a given vehicle. Please refer to the vehicle's workshop manual for specific activation procedures.
- Drive: A drive for a specific monitor requires the vehicle to be driven in such a way that all necessary "enabling criteria" are met for the monitor to run and complete its diagnostic tests. The "drive drive cycle" for a specific monitor begins when the ignition key is turned to "ON." It is successfully completed when all "enabling criteria" for the monitor's operation and completion of its diagnostic tests are met when the ignition key is turned to "OFF." Since each of the fifteen monitors is designed to perform diagnostics and tests on a different part of the engine or emission system, the "drive drive cycle" required for each individual monitor to run and complete is different.
- Drive Cycle: A specific vehicle operating mode that provides the conditions necessary to set all applicable readiness monitors to the "Ready" state. The purpose of completing an OBD II drive cycle is to force the vehicle to perform its on-board diagnostics. A type of drive cycle must be performed after DTCs have been cleared from the PCM's memory or the battery has been disconnected. By completing the full drive cycle of a vehicle, the readiness monitors are "set" so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. Information on vehicle-specific drive cycles can be found in the workshop manual.
- Warm-up Cycle: Vehicle operation after an engine shutdown period, during which the engine temperature rises by at least 22°C (40°F) above the temperature before starting and reaches at least 70°C (160°F). The PCM uses warm-up cycles as a counter to automatically clear a specific code and associated data from its memory. If no faults related to the original problem are detected within a certain number of warm-up cycles, the code is automatically cleared.
- FT (Fuel Trim): Feedback adjustments to the basic fuel plan. Short-term fuel trim refers to dynamic or immediate adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration plan than short-term trim adjustments. These long-term adjustments compensate for vehicle differences and gradual changes that occur over time.
1.4 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are codes stored by the on-board computer's diagnostic system in response to a problem detected in the vehicle. These codes identify a specific problem area and are intended to give you an indication of where a fault might be occurring in a vehicle. OBD II Diagnostic Trouble Codes consist of a 5-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character, a number, 0-3; the other three characters, a hexadecimal character, 0-9 or A-F, provide additional information about where the DTC originated and what operating conditions set it. Below is an example illustrating the structure of the digits:
Example of a Diagnostic Trouble Code (DTC) structure, showing P0202 for Injector Circuit Malfunction, Cylinder 1.
1.5 Data Link Connector (DLC) Position
The DLC (Data Link Connector) is typically a 16-pin connector used to connect the diagnostic code reader to the vehicle's on-board computer. In most vehicles, it is usually located 12 inches from the center of the dashboard, under or around the driver's side. The position of the DLC may vary in some vehicles with special designs.
Refer to the following image for common DLC positions:
Diagram showing common locations for the Data Link Connector (DLC) in various car models (A-Opel, Volkswagen, Audi; B-Honda; C-Volkswagen; D-Opel, Volkswagen, Citroen; E-Changan; F-Hyundai, Daewoo, Kia, Honda, Toyota, Nissan, Mitsubishi, Renault, Opel, BMW, Mercedes-Benz, Mazda, Volkswagen, Audi, GM, Chrysler, Peugeot, Regal, Beijing Jeep, Citroen and other popular models).
If the DLC cannot be found, refer to the vehicle's workshop manual for its position.
2. Product Descriptions
2.1 Components & Controls
Front view of the LAUNCH X431 Creader Elite V2.0 BBA diagnostic tool, showing the screen and control buttons.
| No. | Name | Description |
|---|---|---|
| 1 | Charging Port | Charges the device via a data cable (not included in the scope of delivery). |
| 2 | DB-15 Diagnostic Connector | Connects the diagnostic cable. |
| 3 | Power Button | Turns the device on/off. |
| 4 | Touchscreen | Displays test results. |
| 5 | BACK Button | Exits the current program or returns to the previous screen. |
| 6 | HOME Button | Navigates to the main menu screen. |
| 7 | Settings Button | Quick access to the settings module. |
3. First Use and Connection
3.1 Powering On the Device
There are two methods to power on the device:
- Via Data Cable: Plug one end of the data cable (not included) into the device's charging port and the other end into a PC.
- Via Diagnostic Cable: Plug the diagnostic cable into the vehicle's DLC port. When the device is powered on, the screen will automatically light up.
3.2 Initial Steps
When using this device for the first time, you need to perform some system settings:
- Press the [POWER] button to turn on the device. A welcome page will appear on the screen. Tap "Start" to proceed to the next step.
- Select the desired system language and tap "Next Step."
- Select your current location's time zone. The system will automatically configure the time according to your selected time zone.
- The system will automatically search for all available wireless networks. Select your desired wireless network.
- After the network connection is established, tap "Next Step" to configure the workshop information. Enter the required information and tap "Next Step" to proceed. Note: After configuration, the system will attach this information to the report every time a report is successfully created.
- Carefully read all terms of the user agreement, activate "I agree to all the above terms and conditions," and tap "OK" to complete the registration process. You will be automatically redirected to the main menu.
- Select the diagnostic software/reset software and download it.
3.3 Diagnostic Connection
To connect the device to your vehicle:
- Turn off the ignition.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 1.5 for common locations.
- Plug one end of the diagnostic cable into the vehicle's DLC port and the other end into the device's DB-15 diagnostic connector, then tighten the captive screws.
Diagram illustrating the connection of the diagnostic cable to the vehicle's DLC port.
- Note: Some vehicles may have a plastic DLC cover that needs to be removed before connecting the diagnostic cable.
- Note: The cable connector is keyed and will only fit in one direction. If you have trouble connecting the cable connector to the DLC, rotate the connector 180 degrees and try again.
- Turn on the ignition. The engine can be off or running.
Caution: Do not connect or disconnect test equipment while the ignition is on or the engine is running.
4. Operating the Device
4.1 Main Menu Overview
The main menu primarily includes the following functional modules:
| Module | Description |
|---|---|
| Diagnose | Configures the device to function as a professional diagnostic tool. |
| OBD II | Provides a quick way to check DTCs, isolate the cause of the Malfunction Indicator Lamp (MIL), check monitor status before emission certification testing, verify repairs, and perform various other emission-related maintenance tasks. |
| Special Function | Appears only if you have selected reset software for the first use or after successfully subscribing to reset software in "Mall." Offers coding, reset, relearn, and other service functions to restore vehicles to operational condition after repair or replacement. See Section 4.4 for more information. |
| Upgrade | For updating vehicle diagnostic software and the app. Note: This function requires a stable network connection. |
| Mall | For subscribing to additional vehicle diagnostic software or reset software (special function) not included with the device. |
| More | Includes various modules such as LAUNCH Academy (optional), Online Service, Know Your Customer (optional), Toolbox (Delete Diagnostic Software, Firmware Fix, DTC Library, Diagnostic Record, DLC Search, Feedback), and My (Check saved reports, order information, system settings). |
4.2 System Diagnosis
This function is specifically designed to diagnose electronic control systems of individual vehicle models.
- Note: The vehicle diagnostic software includes all types of reset software that the user can perform directly in this module (select Special Function from the diagnostic function list).
- Note: All software is regularly updated. It is recommended to update and install the latest software version for the best service, functions, and experience.
- Note: The use and update of diagnostic software you selected for the first use is free forever. The use and update of diagnostic software acquired in "Mall" is free for one year. When the subscription expires, the user must renew it.
- Note: Vehicle coverage can be extended for each model. Simply go to "Mall" to subscribe.
4.2.1 Intelligent Diagnosis (Automatic Recognition)
This function allows you to quickly access the vehicle's electronic control systems by decoding the VIN without manual step-by-step menu selection.
After connecting, turn on the ignition, and the system will switch to automatic recognition mode.
- Note: Ensure that the "Automatic Recognition on Connection" option in "Settings" is set to ON.
- Note: A very stable and reliable network connection is recommended for successful VIN access.
A. Successful VIN Retrieval: Once the system successfully retrieves the VIN (Vehicle Identification Number) information of the currently identified vehicle, confirm the VIN information to scan the vehicle systems until the diagnostic session is successfully completed.
B. Failed VIN Retrieval: If the device cannot access the VIN information, the following screen will be displayed:
Screen for manual VIN input when automatic recognition fails, showing a virtual keyboard.
Enter the VIN and tap "OK." The system will automatically decode the VIN data and, if successful, continue with intelligent diagnosis. Otherwise, the system will switch to manual diagnosis mode.
- Note: The most easily recognizable location for this number is in the upper left corner of the vehicle's dashboard. Other locations include the driver's door or pillar and the firewall under the hood.
- Note: Generally, Vehicle Identification Numbers are standardized and all contain 17 characters. VIN characters can be uppercase letters A to Z and numbers 1 to 0; however, the letters I, O, and Q are never used to avoid reading errors. No characters or spaces are allowed in the VIN.
4.2.2 Manual Diagnosis
If the device cannot retrieve or analyze VIN information, you can also perform a manual diagnosis. In this mode, you must execute the menu-driven command and then follow the on-screen instructions to proceed.
- Note: Before diagnosis, ensure that the corresponding vehicle manufacturer's software is installed on the device.
- Note: The diagnostic menu may vary depending on the vehicle's make, model, and year.
Refer to the flowchart below to manually diagnose a vehicle:
Flowchart for manual diagnosis, showing steps like selecting 'Diagnose', vehicle manufacturer, model, scan mode, and test functions.
Take DEMO V15.34 as an example to demonstrate how to diagnose a vehicle:
- Select Diagnostic Software Version: Tap "DEMO" to go to step 2.
- Select Vehicle Model (varies by version): Select the desired vehicle model.
4.2.3 Health Report (Quick Test)
This function varies from vehicle to vehicle. It allows you to quickly access all electronic control units of the vehicle and generate a detailed report on the vehicle's health status.
On the test item selection screen, tap "Health Report." The system will begin scanning the ECUs. Once the scan is complete, the following screen will be displayed:
Health Report screen displaying diagnostic results, indicating systems with fault codes (red X) and systems that are OK (green checkmark).
Buttons on the screen:
- Report: Tap here to save the diagnostic result as a report.
- Clear Code: Tap here to clear existing diagnostic trouble codes.
4.2.4 System Scan
This option allows you to quickly scan which systems are installed in the vehicle.
4.2.5 System Selection
This option allows you to manually select the test system and function step by step.
On the test item selection screen, tap "System Selection" and tap the desired system (e.g., "Engine") to access the test function selection screen.
- Note: Different vehicles have different diagnostic menus.
4.2.6 Read Fault Code
This function displays detailed information about the DTC records retrieved from the vehicle's control system.
On the test function selection screen, tap "Read Fault Code"; the screen will display the diagnostic result.
- Note: Retrieving and using DTCs for vehicle troubleshooting is only part of a comprehensive diagnostic strategy. Never replace a part based solely on the DTC definition. Each DTC has a set of test procedures, instructions, and flowcharts that must be followed to confirm the location of the problem. This information can be found in the vehicle's maintenance manual.
Buttons on the screen:
- Help: Tap here to view help information.
- Code Search: Tap here to search online for more information about the current DTC.
- Report: To save current data in text format. All diagnostic reports can be accessed via More -> My -> My Report.
4.2.7 Clear Fault Code
After retrieving codes from the vehicle and performing specific repairs, you can use this function to clear the codes from the vehicle. Before performing this function, please ensure that the vehicle's ignition key is in the ON position with the engine off.
- Note: If you plan to take the vehicle to a service center for repair, DO NOT clear the codes from the vehicle's computer. If data is deleted, valuable information that could help the technician troubleshoot will also be lost.
- Note: Clearing DTCs does not fix the problem(s) that caused the codes to be set. If proper repairs are not performed to fix the problem that caused the codes to be set, the code(s) will reappear and the "Check Engine" light will illuminate as soon as the problem that caused the DTCs to be set manifests.
4.2.8 Read Data Stream
This option retrieves and displays live data and parameters from the vehicle's ECU.
On the test function selection screen, tap "Read Data Stream." The system will display the data stream items.
Buttons on the screen:
- Select All: Tap here to select all items on the current page. To select a specific data stream item, simply check the box next to the item name.
- Deselect All: Tap here to deselect all data stream items.
- OK: Tap here to confirm and proceed to the next step.
After selecting the desired items, tap "OK" to access the data stream reading page.
- Note: If the value of the data stream item is outside the range of the standard value (reference value), the entire line will be displayed in red. If it matches the reference value, it will be displayed in blue (normal mode).
- Note: The 1/X display at the bottom of the screen stands for the current page/total number of pages. Swipe right/left across the screen to go to the next/previous page.
Three types of display modes are available for data display, allowing you to optimally display different types of parameters:
- Value: Displays parameters with numbers and lists.
- Graph: Displays parameters with waveform patterns.
- Combine: Graphs can be merged for easier comparison. In this case, different items are marked in different colors.
Buttons on the screen:
- Graph: Tap here to display the waveform graph of the current data stream item.
- Combine: Tap here, a pull-down list of data stream items will appear on the screen. Select the required items (max. 4 items can be selected simultaneously) and the waveforms corresponding to these items will be displayed immediately on the screen.
- Report: Tap here to save the current data as a diagnostic report. All diagnostic reports can be accessed via More -> My -> My Report. The device logs the report date (date and time of report creation) and assigns it a unique report number.
- Record: Tap here to record and save live data. Recorded live data can serve as valuable information to help you troubleshoot and diagnose vehicle problems. All diagnostic records can be accessed via More -> Toolbox -> Diagnostic Record.
4.3 Special Functions
This device offers coding, reset, relearn, and other service functions to restore vehicles to operational condition after repair or replacement. The available tests vary depending on the vehicle manufacturer, model, and year.
Image detailing ECU Coding/Backup/Personalization/Retrofit and Key Programming functions.
Due to continuous improvements, service functions may change without prior written notice. To use more service functions, it is recommended to check for updates regularly.
4.3.1 Subscribe to Reset Software
If the "Special Function" module is not displayed in your device's main menu, it will be activated and appear after you successfully subscribe to the reset software in "Mall."
The subscription period is one year and starts from the date of subscription. After expiration, it will be automatically deactivated, and the user must renew their subscriptions in Mall.
- Note: The diagnostic software of the selected vehicle includes all types of reset software that are not directly accessible in this module.
- Note: If the test vehicle is the selected vehicle, simply go to "Diagnose" to perform the special function.
- Note: If you are testing a vehicle other than the selected one, subscribe to the target reset software and perform the special function in this module.
After successful subscription and download, it is ready for use.
4.3.2 Perform Reset Procedure
There are two methods available for performing reset procedures: Manual Reset or Automatic Reset. Automatic Reset follows the principle of sending a command from the device to the vehicle's ECU to perform the reset. For manual reset, users simply follow the on-screen instructions to select appropriate execution options, enter correct data or values, and perform necessary actions. The system will guide you through the entire execution of the various service operations.
Follow the flowchart below to perform the reset:
Image detailing various reset functions available, such as Oil Reset, ABS Bleeding, Throttle Reset, Injector Coding, SAS Reset, EPB Reset, BMS Reset, DPF Reset, etc.
4.4 OBD II Diagnosis Functions
This function provides a quick way to check DTCs, isolate the cause of the Malfunction Indicator Lamp (MIL), check monitor status before emission certification testing, verify repairs, and perform various other emission-related maintenance tasks.
After the device is properly connected to the vehicle's DLC, tap "OBD II" in the main menu. The device will automatically check the vehicle's computer to determine the type of communication protocol used and then display the monitor status. Tap "OK." The following function list will be displayed:
Image showing the full 10 OBD2 test modes supported by the scanner.
- Read Codes: This function checks whether the various emission-related systems of the vehicle are functioning correctly and are ready for inspection and maintenance tests. It can also be used to check the monitor's running status and confirm whether a vehicle fault has been correctly repaired.
- Read Live Data: This function retrieves and displays live data and parameters from the vehicle's ECU.
- Read Freeze Frame: This function creates a snapshot of operating conditions when an emission-related fault occurs.
- Clear Fault Code: This function clears the codes from the vehicle after codes have been retrieved from the vehicle and specific repairs have been performed. Ensure that the ignition key is in the ON position and the engine is off before proceeding.
- Test Results: On-Board Monitoring Test: This function retrieves test results for emission-related powertrain components and systems that are not continuously monitored. The availability of the test is determined by the vehicle manufacturer.
- Control of On-Board Component/System Operation: This option is used to access tests of vehicle-specific subsystems and components. The available tests vary depending on the vehicle manufacturer, year, and model.
- Read Vehicle Information: This function retrieves a list of information (provided by the vehicle manufacturer) from the vehicle's on-board computer. This information may include: VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
- EU OBFCM: This function displays a list of vehicle information provided by the vehicle manufacturer that complies with CO2 emission standards for new passenger cars and new light commercial vehicles (Regulation EU 2019/613). This information may include: Vehicle Identification Number, Total Fuel Consumption (Lifetime), and Total Driving Distance (Lifetime), etc.
4.5 History
Once a vehicle diagnosis has been performed, the device generally records all details of the diagnostic session.
The history function provides direct access to previously tested vehicles, and users can continue from the last operation without having to start over. Tap "History" on the main diagnostic menu screen. All diagnostic records will be listed on the screen in chronological order.
5. Maintenance and Updates
5.1 Upgrade
This function allows you to update the diagnostic app and software. All software is regularly updated. It is recommended to update and install the latest software version for the best service, functions, and experience.
- The use and update of diagnostic software/reset software that the user installed for the first use is free forever. No subscription renewals are required.
- The use and update of diagnostic software/reset software purchased in "Mall" is free for one year. When the free period expires, the user must renew the subscription.
Note: Ensure that the network connection is strong and stable during the update.
5.1.1 Update Diagnostic Software & App
Tap "Upgrade" in the main menu to access the Update Center.
By default, all diagnostic software is selected. To deselect specific software, tap "Deselect All" and then check the box next to the vehicle model. Tap "Update" to start the download. It may take a few minutes for the process to complete. Please be patient. Once the download is complete, the software packages will be installed automatically.
5.1.2 Extend Subscription
The use and update of software configuration purchased in "Mall" is free for one year. When the free period expires, the current version software will be locked. To unlock it, the user must renew the subscription.
Tap "Upgrade" in the main menu to access the Update Center. If the free period has expired, a corresponding message will be displayed on the screen. Tap "Renew" to open "Mall." Select the desired diagnostic software configuration and then follow the on-screen instructions to complete the update. The latest diagnostic software is now ready for use.
5.2 Mall
This function allows you to subscribe to other vehicle diagnostic software and reset software that is not pre-installed on the device.
All diagnostic software in Mall covers full systems and full functions (without online programming and coding, etc.). Different vehicle software is priced differently.
Tap "Mall" to open the Online Software Mall. Select the target software and follow the on-screen instructions to complete the transaction.
Note: The software service belongs to virtual goods. It takes effect immediately from the date of successful transaction and does not accept refunds. Please check the order information when paying. The subscribed software can be used and updated for one year free of charge. After expiration, it will be deactivated. In this case, you must re-subscribe to it in Mall to unlock it.
5.3 Toolbox
The "More" section includes a "Toolbox" with several practical additional modules:
- Delete Diagnostic Software: This option allows you to delete diagnostic software that is not frequently used.
- Firmware Fix: Use this module to update and repair the diagnostic firmware. Do not interrupt the power supply or switch to other interfaces during the upgrade process.
- DTC Library: This function allows you to retrieve the details of DTCs, which greatly simplifies the diagnostic process.
- Diagnostic Record: This module stores the operating parameters or waveform diagrams recorded by the user.
- DLC (Data Link Connector) Position: This function allows you to determine the position of the vehicle's DLC.
- Feedback: This function allows you to send feedback on your diagnostic problems to us for further analysis and troubleshooting.
- Diagnostic Report: This module stores all diagnostic reports generated during the remote diagnosis process.
- Image (Screenshots): This option allows you to view and manage all screenshots taken during vehicle diagnosis. All screenshots are stored in this module.
- User Manual: The user manual is integrated into the device so you can easily check and refer to it.
5.4 Other Settings
The "My" section allows you to check saved reports, order information, and perform some system settings:
- My Report: With this option, you can check and manage your saved reports. All diagnostic reports are sorted by date and brand. If too many reports are stored, tap (Search) to filter and quickly find them.
- My Order: With this option, you can check order information.
- Settings: With this module, you can make some system settings according to your preferences.
- Units: With this option, you can set the unit of measurement. The metric system and the English system are available.
- Automatic Recognition on Connection: With this option, you can determine whether an automatic VIN recognition should start as soon as the device is properly connected to the vehicle's DLC.
- Brightness: With this item, you can set the standby time and screen brightness.
- Sound: With this option, you can adjust the volume and other sound settings.
- Network: With this option, you can set up Wi-Fi networks that can be connected.
- Time Zone: With this option, you can set the time zone.
- Language: The device supports multiple languages. With this option, you can set the preferred language. Note: After switching the language, download all diagnostic software again, otherwise the system will use the English software by default.
- Workshop Information: With this option, you can set the standard email address for receiving diagnostic reports or screenshots, as well as workshop information. Note: After configuration, the system will attach it to the report every time a report is successfully created.
- Restore: With this option, you can reset the device to factory default settings. Warning: Resetting can lead to data loss. Before doing this, please perform this process carefully.
- Screenshot: With this option, you can determine whether the screenshot icon should be displayed on the screen or not. If this option is set to ON, a screenshot icon floats in the upper right corner of the screen. Tap it to capture the screen.
- About: This option displays information about the device's hardware configuration and the license agreement.
6. Troubleshooting and FAQ
This section addresses common questions and issues you might encounter with your device.
6.1 Frequently Asked Questions (FAQ)
The device includes an FAQ section (accessible via More -> Toolbox -> FAQ) that lists common questions and answers. For specific issues, consider the following:
- Compatibility: If you are unsure about compatibility with a specific vehicle model (e.g., Peugeot 207 SW 2009 for gearbox relearn, or a specific Mercedes-Benz S550), it is recommended to check with the manufacturer or seller, providing the VIN if possible.
- Diesel Cars: The device is generally designed for 12V passenger cars. For specific compatibility with diesel cars, refer to the vehicle coverage list or contact support.
- Specific Functions: Not all advanced functions like ECU coding or active tests are universal for all vehicles. Always verify compatibility for your specific car's make, model, and year before attempting these functions.
6.2 User Tips
- Wired Connection: The device primarily uses a wired connection to the vehicle's OBD-II port. Ensure the cable is securely connected for stable communication.
- Software Updates: Regularly update the diagnostic software via Wi-Fi to ensure you have the latest features and vehicle compatibility.
- Check VIN: When performing diagnostics, especially intelligent diagnosis, always confirm the VIN to ensure accurate vehicle identification.
- Backup Data: Utilize the diagnostic record and report functions to save important diagnostic data for future reference or sharing.
7. Specifications
The following are the technical specifications for the LAUNCH X431 Creader Elite V2.0 BBA:
- Screen Size: 4 inch Touch Screen
- Resolution: 480*800 pixels
- CPU: 4-core 1.3GHz processor
- RAM: 2GB
- ROM: 16GB
- Battery: 3000mAh
- WiFi: 802.11b/g/n 2.4GHz
- USB: TYPE-C
- OBD II Input Voltage Range: 9~18V
- Power Up Via: DC 5V data cable or Diagnostic cable through connection to vehicle's DLC
- Working Temperature: -10℃ to 45℃ (14℉ to 113 ℉)
- Storage Temperature: -20℃ to 70℃ (-4℉ to 158 ℉)
Image showing the product packaging and the diagnostic device, highlighting key specifications and features.
8. Warranty and Support
8.1 Warranty
This warranty is expressly limited to persons who purchase LAUNCH® products for resale or use in the normal course of business. The LAUNCH® electronic product is warranted to be free from material and manufacturing defects for one year (12 months) from the date of delivery to the user.
This warranty does not cover parts that have been misused, altered, used for a purpose other than intended, or used in a manner inconsistent with the operating instructions. The exclusive remedy for a defective vehicle instrument is repair or replacement, and LAUNCH is not liable for consequential or incidental damages.
The final determination of defects is made by LAUNCH according to established procedures.
8.2 Customer Service
If you have any questions during the operation of the device, please contact the seller or the LAUNCH TECH Service Center.
- Website: https://en.cnlaunch.com
- Phone: +86 755 8455 7891
- E-Mail: overseas.service@cnlaunch.com
9. Compliance Information
9.1 FCC and IC Compliance
FCC ID: XUJOCEX403
IC: 29886-CREV2
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Innovation, Science and Economic Development Canada's license-exempt RSSs and Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference; and
- This device must accept any interference received, including interference that may cause undesired operation.
This digital apparatus complies with Canadian standard ICES-003.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
9.2 Specific Absorption Rate (SAR) Information
This product meets government requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a significant safety margin designed to ensure the safety of all persons, regardless of age or health status.
The SAR limit is 1.6 W/kg averaged over one gram of tissue. This device has also been tested against this SAR limit. This device was tested for typical body-worn operation at a distance of 0 mm from the body. To comply with RF exposure requirements, use accessories that maintain a distance of 0 mm from the user's body.
9.2.1 Body-Worn Operation
This device was tested for typical body-worn operation. To meet RF exposure requirements, a minimum separation distance of 0 mm must be maintained between the user's body and the antenna. Belt clips, holsters, and similar third-party accessories used with this device must not contain metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
This device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The RF frequencies can be used without restrictions in Europe.