MEKEDE M90S

Contents

MEKEDE Android Car Multimedia System Instruction Manual

Model: M90S

For Mercedes Benz Smart Fortwo 451 (2006-2009)

1. Introduction

Dear Customer: Thank you for trusting and purchasing our car multimedia system. To ensure effective and safe use of your device, please read these instructions carefully before use.

Note: Due to the continuous improvement of our products, some descriptions in this manual may differ from the actual equipment. Specifications are subject to change without notice.

1.1 Safety Measures

  • It is forbidden to watch videos or other visual accessories while driving. Active use of the system during driving is not recommended because it can reduce attention and may result in violation of DA and road accidents.
  • The unit is designed for use in cars with a 12V power supply and a minus ground. Do not install the system in a bus or truck with an on-board voltage of 24V. This may cause damage to the device.
  • Use a special cleaning device to take care of the screen.
  • To avoid overheating of the device, do not allow direct exposure to sunlight and do not install near the heating system. Operating temperature is between 0°C and 35°C. If the temperature inside the vehicle is too high, it is necessary to cool the interior before switching on the system. It is also not recommended to operate the unit at very low temperatures. It is necessary to wait until the temperature of the interior and the vehicle returns to normal. When the temperature is low, the image on the screen may change with a delay. This is not a malfunction. Wait until the multimedia system reaches the operating temperature.
  • Only use the fasteners provided (screws, mounting frames, etc.) for installation. The use of other fasteners may result in damage to the system, and this is not covered by the warranty.
  • Installation and connection of the device shall be performed by a qualified specialist, or specially trained staff of the service center.
  • Do not reset to factory settings on your own unless in extreme cases, as this will cause loss of your settings, which may result in incorrect operation of the system.
  • Violation of the above items and improper use may cause the system to malfunction. In this case the warranty service will not be performed.

2. Setup

2.1 Multimedia System Package Contents

The package includes the following components:

Package Contents: Machine, Power Cable, RCA Cable, USB Cable, Reversing Camera, GPS Antenna

Image: Package Contents including the main unit, power cable, RCA cable, USB cable, reversing camera, and GPS antenna.

  • Machine (Main Unit)
  • Power Cable
  • RCA Cable
  • USB Cable
  • Reversing Camera
  • GPS Antenna

2.2 Connection Diagram of the Device

Refer to the diagram below for proper connection of all components.

Connection Diagram of the Device

Image: Detailed wiring diagram for the car multimedia system, showing connections for power, audio, video, GPS, and other peripherals.

2.3 Rear Camera Connection Method

Without CANBUS Box:

  • Connect the reversing mode control wire to G5.
  • Connect the rear camera control wire to the car reversing light 12V power supply.
  • Connect GND to Car Ground.

With CANBUS Box:

  • Connect ACC to G3 ACC.
  • Note: The yellow line connection is not needed if you already have a CANBUS box and the reverse control line (G3 area) has been connected to the CANBUS box.
  • Connect the two red wires together for camera power, do not connect with other wires.
  • Connect GND to Car Ground.

2.4 CANBUS Box Setup

If your car's original functions (like steering wheel control) cannot be used, a CANBUS type needs to be set. Check your CANBUS photo and select the corresponding type.

Setup Steps for TS7 T3L TS18 TS10 M100 M150 and Y1 Y2 TS100 TS150 TS200:

  1. Connect as shown in the picture.
  2. Go to Settings > Car Settings > Factory (Password: 8888).
  3. Select the appropriate CANBUS type from the list.

Note: The CANBUS cable must be plugged in for Wi-Fi to work properly.

3. Operating Instructions

3.1 Introduction to the Device

The main unit features a touchscreen display and physical buttons for control.

Front Panel Control:

  1. Microphone
  2. Emergency reassembly of equipment
  3. Input/output switch/live switch/sound switch
  4. Return to main menu
  5. Switching back to the previous menu
  6. Increase volume
  7. Lower the volume

3.2 Switching the Appliance On/Off

Switching On: After switching off the ignition and starting the engine, the multimedia system is automatically switched on. The display shows the initial screen. The unit activates automatically after the engine is switched off.

3.3 Touch Screen Operation

This unit is equipped with an interactive touchscreen display. Before using it for the first time, the sealed plastic membrane must be removed. Otherwise the touch screen may not function properly.

  • Touch: Click the necessary item with your finger to start the plugin (signal source) or select the menu item (option).
  • Double Tap: A quick double touch allows you to resize when viewing images.
  • Touch & Hold: Click and hold the item for 2 seconds to trigger an additional action available for that item.
  • Dragging: Touch and hold the selected item, then drag it onto the screen.
  • Moving: Rotate the screen with your finger and keep your finger touched, move your finger in the right direction throughout the screen.
  • Scroll through: Move your finger on the screen in the direction you need to and let go. Rotation can be stopped by touching the screen, or wait until the motion stops itself.

Attention! Do not use metal or sharply sealed objects to control sensory interactive display. Also don't apply excessive force when touching the screen.

3.4 Main Interface Customization

Customize the position of icons in the main interface, and all applications can be freely edited according to the position of the quick menu bar for easy operation.

Click and hold an icon on the main menu to replace the application.

3.5 Change Wallpaper of Main Menu Interface

You can set a picture or a photo as a background for the main screen. You can choose from the previously installed Live Spreadsheets (Live wallpaper) and Spreadsheets (wallpaper) or you can choose from images or photos stored on a USB memory device or SD memory card.

Long press on the main menu background to access wallpaper options.

3.6 FM/AM Radio

To access the Radio, click the appropriate icon (Radio) on the main menu.

FM RDS Radio Interface

Image: FM RDS Radio interface showing frequency display and station presets.

Features:

  1. Main menu
  2. FM switching group
  3. LOC mode or DX mode: "LOC" for strong signals, "DX" for all stations in range.
  4. MONO mode
  5. Automatic scanning of stations
  6. Save station
  7. Additional adjustments
  8. List of saved stations

By tapping on the scale bar, you can quickly select the desired frequency.

3.7 DSP Processor/Equalizer

To access the equalizer (EQ) option, press the (Radio) or (Equalizer) icon on the menu. The DSP chip allows for advanced sound settings.

Equalizer Mode: Adjust sound using different frequency settings. Adjust volume of 32 bands. Presets include Rock, Soft, Jazz, Pop, Classical, Hall. Press "Standard" to reset.

Automatic Volume Mode: Choose recommended settings for listener position (Driver, Passenger, Rear, Center) or adjust manually on the car diagram.

Bass Enhancement: Reverse high and low frequency tones, change boost factor.

Bass Filter: Set desired frequency for each speaker. Available values: Front Dynamics / Rear Dynamics.

3.8 Music / Video Playback

Connect a USB storage device or insert an SD memory card and press (music) for music playback, press (video) for video playback.

1080P Video Playback

Image: Display showing 1080P video playback on the unit.

The format supported by the video player is as follows: MP4 / AVI / WMV / MOV / MKV / MPEG / RMVB etc.

Attention! Given the security of the video, you cannot view it while the car is in motion. To view the video, stop in a safe place and apply the handbrake.

3.9 Bluetooth (BT) Function

In the main menu, click the "BT" icon to enter the hands-free interface. Open your phone's BT "search for new devices" function. When the system and phone connect, confirm the connection and enter the password (0000). The system screen will show "connected".

Bluetooth Function Interface

Image: Bluetooth interface showing dial pad, contacts, and music playback options.

Features:

  • Call log
  • Dialing interface
  • Telephone book
  • BT music
  • Check connection
  • BT settings

3.10 Car-Play / Android Auto

Car Link allows you to use your iPhone and Android in the car without being distracted. You can use navigation, make calls, send messages, listen to music, etc.

Wireless Car-Play (iOS System) Connection Steps:

  1. Connect your phone via BT.
  2. Tap on "Car Link", the phone will ask for authorization to connect. Authorize and wait for connection.

Android Auto Connection Steps:

  1. Connect the mobile phone and car DVD player with USB cable.
  2. Tap on "Car Link", the phone will ask for authorization to connect. Authorize and wait for connection.
CarPlay and Android Auto Interface

Image: Display showing both Wireless CarPlay (iOS) and Wired Android Auto (Android) connection steps and interfaces.

3.11 Split Screen

On the screen of the main device, you can display two additional devices simultaneously, for example, the navigation program and music.

To exit the split screen mode, pull to the right the icon between the two screens.

3.12 MAP Navigation

Built-in global positioning system, omnidirectional map display, synchronous real-time traffic display, fast and accurate positioning.

GPS Navigation Display

Image: GPS navigation display with map, speed, and time information.

The following navigation APPs are supported: Navitel, IGO, Yandex, Google.

3.13 Cooling Fan Operation

Setup Steps:

  1. Go to Settings > Device > USB Device Start.
  2. Set Power Conditioning to 60.
  3. The cooling fan starts working.

3.14 4G LTE Connectivity

Connected to 4G, you can watch live video, listen to music online, play games, watch movies and make your car seamlessly connected to the Internet at any time.

4G Card Slot:

  1. Push the iron plate down and open it.
  2. Insert the SIM card.
  3. Pull up the iron plate to fix the SIM card in place.

3.15 Language Settings

Select the language you want to set and press and hold this button to move to the first position.

3.16 Main Menu Interface Settings

Our products have 5 different main menu screens that you can choose to display according to your preferences.

Setup Steps:

  1. Tap on "Settings" > Factory (Password: 3368).
  2. Find "Home Launcher Selection".
  3. Select the desired main menu interface (e.g., U113, U122, UI17, UI20, UI29).

3.17 Lantern Settings (RGB)

The device has a multicolor illumination and can be set to different modes of light.

Settings:

  • Select the light color (RED, GREEN, BLUE) or set it to automatic color change.

4. Optional Features (Additional Accessories)

Note: Additional accessories must be purchased separately to use the following features.

4.1 DAB+ (Digital Audio Broadcasting)

EU DAB+ radio universal for all Android radios, providing better sound quality and stronger signal. Only for buyers from EU countries.

4.2 OBDII (On-Board Diagnostics II)

With the OBDII function, you can monitor real-time data and fault codes from your vehicle's computer, such as oil, fuel speed, and temperature.

OBDII Feature Display

Image: Display showing OBDII interface with engine management diagnostics and tools. OBDII module is not included.

4.3 TPMS (Tire Pressure Monitoring System)

After correctly installing the TPMS in your car, the sensors will automatically monitor tire pressure and temperature, transmitting real-time statistics to the receiver.

TPMS Feature Display

Image: Display showing TPMS interface with tire pressure and temperature readings. TPMS module is not included.

4.4 AV Output

The video output can display content on external screens, allowing rear passengers to watch HD video and audio through the video cable from the navigation console to headrest displays.

4.5 360° Camera System

If you want to add a 360 camera, you must order it along with your car radio, as a built-in 360 Camera Chip is needed on the motherboard radio. To turn on the 4 cameras, refer to the manual's instructions.

4.6 ADAS DVR (Advanced Driver-Assistance Systems Digital Video Recorder)

The ADAS DVR provides anti-collision warning features, including front vehicle distance prediction, front vehicle anti-collision warning, and lane departure warning to enhance driving safety.

ADAS DVR Feature Display

Image: Display showing ADAS DVR interface with front vehicle distance prediction and warning indicators. DVR is not included.

4.7 AHD Reversing Video

The picture quality of AHD rear-view video is clearer than that of ordinary cameras.

AHD Reversing Video Display

Image: Display showing AHD reversing video feed with parking guidelines. Rear view camera is not included.

5. Troubleshooting

If you experience a problem, try disconnecting and then reconnecting your device. Use the special key to press the Reset button. If this does not solve the problem, please refer to the table below. These instructions will help you to solve the problem if the device does not work properly. Otherwise, check that the device is properly connected or consult your authorized dealer.

SymptomsProbable CauseSolution
General Problems
The ignition key is not in the "On" position.Turn the key to the "On" position.Check the presence of the circuit breaker in the device, if it is not working, replace it with a good one of the same nominal size.
Overheated fuses 15A.Check the presence of the circuit breaker in the device, if it is not working, replace it with a good one of the same nominal size.Check the presence of the circuit breaker in the device, if it is not working, replace it with a good one of the same nominal size.
Incorrect connection of the electrical supply droplets (black and yellow).Check the connection of the electrical supply.Check the connection of the electrical supply.
Bluetooth (BT)
Phonebook contacts are not transferred.No rights on the phone.After connecting the phone to the device, go to the BT setting on the phone, and authorize the transfer of the phone book.

6. Technical Specifications

AttributeSpecification
Mounting Size9"/10"
Screen Resolution1280x720 IPS
Screen Size9 inch
CPU4-Core
RAM1GB/2GB/4GB
ROM32GB/64GB
Operating SystemAndroid 13
Maximum Output Power4 x 45 W
Sound AmplifierTDA7388
Chip FM TunerNXP TEF6686
Features of the EqualizerLow Pass Filter, Tone Compensation, Balance Mode, Surround Sound Mode, Extended Equalizer settings (32 bands)
Car-Play / Android AutoBuilt-in (2GB+32GB)
Video FormatRMVB, MKV, MOV, WMV, AVI, MPG, TS, H.264 codec and others.
Audio FormatMP3, WMA, WAV, OGG, FLAC
GPSBuilt-in receiver with external antenna
Software for NavigationSupport
Wi-FiSupport
360° CameraOptional
BTA2DP and BT address book transfer
Control of Steering Wheel ButtonsSupport
ADAS DVRActivation in the settings menu
AHD HD ReversingAutomatic activation of video input
4G Internet / 4G LTESupport
DSPSupport
Start16s ~ 20s
Voltage during operationDC12V
Voltage at operating range9V ~ 16V
Electric Current15A
Operating Temperature-20°C ~ +70°C
Main Menu LanguageSupport for multiple national languages

7. Warranty and Support

The product comes with a 1-year manufacturer's limited warranty for defective items (excluding items damaged and/or misused after receipt). Accessories come with a 3-month warranty.

Defective items MUST be reported and returned within the warranty period (and in the original packaging if possible). You must tell us what the defect is and give us your order number. We do not repair or replace items with an expired warranty.

For further support, please refer to the official user manual PDF: User Manual (PDF)

8. User Tips

  • Side Button Backlight: If the side button backlight is not active, check the system settings for illumination or display options. Sometimes this can be found under 'Lantern Settings (RGB)' or similar display customization menus.
  • Reverse Camera Issues: If the reverse camera works initially but stops working after the Android system starts, verify the camera's power connection and signal input. Ensure all cables are securely connected and check the camera settings within the car multimedia system. Refer to the 'Rear Camera Connection Method' in the setup section.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.