GOYOJO ECI-V1

Contents

Wireless Veterinary Ultrasound Scanner

Model: ECI-V1 | Brand: GOYOJO

1. Introduction

The GOYOJO ECI-V1 Wireless Veterinary Ultrasound Scanner is an intelligent, portable B-ultrasound tester designed for animal pregnancy testing. Utilizing the latest wireless data transmission technology, it represents a new generation of animal ultrasound imaging equipment. It is primarily used for pregnancy detection in animals such as pigs and sheep.

This manual provides a complete guide for users operating the intelligent B-ultrasound scanner with Android mobile phone systems. Please read all instructions carefully before operation to ensure proper use and to avoid unnecessary risks.

2. Setup

2.1 Unpacking

The intelligent ultrasound tester is carefully packaged to prevent damage during transport. Before opening, inspect the outer packaging for any visible damage. After opening, verify that all ordered items are present and in good condition. If any defects or damage are discovered, contact your dealer immediately.

Packaging Contents:

  • Wireless Probe: 1 unit
  • USB Charging Cable: 1 unit
  • Wrist Strap: 1 (optional)
  • User Manual: 1 (optional)
  • Waterproof Bag: 1 (optional)

2.2 App Installation

The device operates with the "Full Digital Wireless Ultrasound" application. For Android devices, if the app is not already installed, download and install it by scanning the QR code below using your device's browser.

QR Code for App Download

Scan this QR code to download the Android application.

2.3 Starting the Probe

Familiarize yourself with the probe's components and indicators:

Wireless Ultrasound Probe Diagram

Diagram of the Wireless Ultrasound Probe showing status indicators, power button, and USB plug.

Status Indicators (from left to right):

  1. Power-on Indicator: Always on after the device is powered on.
  2. Wi-Fi Indicator:
    • Slow blinking: Wi-Fi is ready but not connected to a mobile device.
    • Steady on: Wi-Fi is connected, and the probe is in a frozen state.
    • Fast blinking: Wi-Fi is connected, and the probe is actively running.
  3. Charging Indicator: Lights up while the device is charging.
  4. Battery Indicator:
    • Red: Battery is critically low; charge immediately.
    • Green: Charging is complete.

Switch Button Functions:

  • Short press (when off): Turns the device on.
  • Long press (when on): Turns the device off.
  • Short press (after Wi-Fi connection): Toggles between B-ultrasound running and freezing states.

To start the probe, short press the switch button. After a few seconds, the Wi-Fi indicator light will begin blinking, indicating the probe is ready for connection.

2.4 Wireless Connection

When the Wi-Fi indicator light is slowly blinking, the probe's Wi-Fi is active and waiting for a mobile phone or tablet to connect. Open the "Full Digital Wireless Ultrasound" app on your device. The app interface will display available Wi-Fi networks.

App Start Interface

Screenshot of the app's start interface showing available Wi-Fi networks.

Locate and select the Wi-Fi network corresponding to your ultrasound equipment. The Wi-Fi name (SSID) typically follows the format "ECIQ 1AXXXXXXX". Enter the Wi-Fi password, which is "eci" followed by the last seven digits of the Wi-Fi name (e.g., if SSID is ECIQ 1A1906001, password is eci1906001). The password is also printed on the back of the wireless B-ultrasound machine.

Probe Back with SN

The serial number (SN) on the back of the probe contains the Wi-Fi password information.

Once connected, the Wi-Fi name will be displayed in the upper left corner of the app interface.

3. Operating Instructions

3.1 App Operation Interface

The main app interface provides various controls and displays:

App Main Interface

Main operation interface of the ultrasound application.

Key Interface Elements:

  1. Gain Display
  2. Depth Display
  3. Run/Freeze Status Display
  4. Screen Flip
  5. Save Picture
  6. Freeze/Run Button
  7. Turn Up Gain
  8. Turn Down Gain
  9. Turn Up Depth
  10. Turn Down Depth

3.2 Freeze/Run Function

When the app is first launched, the image area may not be active. Tap the "Freeze/Run" button (usually labeled with a snowflake or play icon) to unfreeze the image and begin real-time scanning. The image will then be displayed in the main area.

Frozen State

App in frozen state.

Running State

App in running (live) state.

3.3 Scan Preparation

After connecting the probe, ensure the image is unfrozen. Adjust the gain between 30 and 105Db using the "Turn Up Gain" and "Turn Down Gain" buttons. The current gain value is displayed on the main screen. While scanning, slide your finger up or down on the screen to adjust the detection depth between 100-180mm. The current depth value is also displayed.

3.4 Scanning

Once all preparations are complete, tap the "Freeze/Run" button or short press the probe's switch button to start scanning. The status indicator in the lower left corner of the app will show "Running". Adjust the probe's scanning position, angle, and other factors on the animal until a clear and suitable ultrasound image appears.

3.5 Saving Images and Videos

When a suitable image is obtained, short press the probe's switch button or tap the "Freeze/Run" button in the app to freeze the image. Then, tap the "Save Picture" button on the main screen to save the current image. Saved images can be viewed in your device's photo album.

Note: The first time you save an image, you will need to enter an ID and Breed for the animal. Tap "Save" to proceed. Mobile phones typically save only pictures. Devices with higher resolution, such as tablets, may also support video saving. The app interface on tablets will feature an additional button for saving videos.

4. Maintenance

4.1 Probe Charging

The probe is charged via USB. Locate the USB silicone plug at the end of the probe (refer to the probe diagram in Section 2.3). Open the plug and connect the provided USB charging cable to a power source. When the battery indicator light turns red, it signifies low battery and requires immediate charging. The charging indicator will light up during charging. A full charge takes approximately 3 hours, indicated by the battery indicator turning green.

After charging, unplug the USB data cable and securely close the probe's USB silicone plug to prevent water ingress, especially during cleaning. Store the USB cable properly. Replacement Android USB cables can be purchased if lost.

4.2 Cleaning

Clean the probe after each use. The front end of the probe can be rinsed directly with water or wiped with a damp cloth/paper towel. The probe has an IPX-5 waterproof rating, allowing for short-term rinsing with clean water. Do not immerse the probe in water directly.

4.3 Storage

When not in use, store the probe in its original packaging or a suitable protective case to prevent damage from impact. Avoid exposing the probe to high temperatures. The recommended storage temperature range is 0°C to 40°C.

5. Troubleshooting

  • Probe not turning on: Ensure the battery is charged. Connect to the charger and check the charging indicator.
  • Cannot connect to Wi-Fi: Verify the probe's Wi-Fi indicator is blinking slowly. Ensure you are selecting the correct SSID and entering the password accurately (eci + last 7 digits of SSID). Try restarting both the probe and your mobile device.
  • No image displayed in app: After connecting, tap the "Freeze/Run" button to activate the live image. Check probe placement and contact with the animal.
  • Poor image quality: Adjust the gain and depth settings in the app. Ensure proper contact between the probe and the animal's skin, using ultrasound gel if necessary (though not explicitly mentioned, it's standard practice).
  • App crashing/freezing: Ensure your Android device meets minimum system requirements (if specified, otherwise assume recent versions). Try restarting the app or your device.

6. Specifications

The GOYOJO ECI-V1 Wireless Veterinary Ultrasound Scanner features the following technical specifications:

Product Parameters

Visual representation of key product parameters.

FeatureSpecification
TypeWireless Mechanical Probe Ultrasound
DisplayMobile phone
Scanning Method80° sector scanning
Transducer3.5MHz transducer
Scanning Depth100-180mm (Adjustable)
Display ModeB-mode
Grayscale256 levels
GainAdjustable (30-105Db)
Battery LifeOver 4.5 hours
Size150mm x 54mm x 45mm
Weight0.24kg
Waterproof RatingIPX-5
Image/Video StorageCan be saved to smart terminal (mobile phone/tablet)

7. User Tips

  • Display Compatibility: The device is designed to display images on Android mobile phones and tablets. Notebook compatibility is not guaranteed unless specific software is available.
  • Connectivity: This ultrasound scanner uses Wi-Fi for connection to your smart device, not Bluetooth. Ensure your device's Wi-Fi is enabled and connected to the probe's network.
  • App Availability: The application is typically downloaded via a QR code provided in the manual. It may not be available on standard app marketplaces. Language support for the app is usually English by default, but check app settings for other options.
  • Android Version: While specific Android version compatibility is not listed, it is generally recommended to use a relatively recent Android OS version for optimal performance and stability.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or refer to the seller's support contact details. Keep your purchase receipt as proof of purchase.

Seller's support email: james.m@goyojo.com


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.