General Safety Warnings
Read and understand all instructions in this manual before using the product. Keep these instructions for future reference and pass them on to any subsequent user.
This product is intended for household use only. Use it only as described in this manual. Do not use the product if it is damaged in any way.
This product is intended for use by persons aged 18 years and above. It may be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge only if they have been given supervision or instruction and understand the hazards involved.
WARNING: Ensure correct polarity when connecting to a power source. Reversing positive and negative poles can cause severe damage to the device and potential injury.
Product Overview
The DX10 Mini Spot Welding Machine is a compact and portable tool designed for precision spot welding of battery packs. It features an OLED color screen for clear display of operational parameters and a high-capacity internal battery, also allowing it to function as a portable power bank.


Key Features:
- Compact and Portable: Lightweight design for easy transport.
- Durable Construction: Made from hard aluminum alloy for long service life.
- OLED Display: Provides real-time information including delay time, power levels, remaining battery life, battery voltage, and charging current.
- High-Power MOSFETs: Equipped with six built-in 300A MOSFETs for high redundancy and low failure rate.
- Adjustable Settings: Offers 31 levels of adjustable delay time and 101 levels of adjustable spot welding power.
- Precision Welding: Capable of welding 0.1-0.15mm nickel plates.
- Dual Functionality: Can be used as a spot welder and a portable power bank.
- Fast Charging: Supports Type-C charging.
Specifications
| Attribute | Value |
|---|---|
| Model Number | Portable Spot Welder (DX10) |
| Battery Capacity | 5300mAh / 10600mAh (optional) |
| Material | Aluminum Alloy |
| Product Dimensions (L x W x H) | 148.00 x 82.00 x 27.00 mm (5.83 x 3.23 x 1.06 inches) |
| Weight | 620.00 g |
| Weldable Nickel Plate Thickness | 0.1 - 0.15 mm (up to 0.3mm under full charge) |
| Spot Welding Power Adjustment | 101 levels (Range 1-20 on display) |
| Delay Time Adjustment | 31 levels (Range 0.5 - 2.5 seconds on display) |
| Spot Welding Pen Cable | 8AWG 300mm cables with 6mm copper tips |
| Charging Port | Type-C |
| USB Output | Yes |
| Certification | CE, FC, RoHS |
| Is Smart Device | No |

Package Contents
- 1 x DX10 Mini Spot Welding Machine
- 1 x Pair of Spot Soldering Pens
- 1 x Type-C Charging Cable
- 1 x Nickel Plate Sample

Setup
Connecting to an External Power Source (e.g., Car Battery)
- Prepare the Battery Terminals: If connecting to a car battery, drill a 3mm hole into both the negative and positive terminals of the battery.
- Connect Negative Terminal: Attach the negative cable of the spot welder to the negative terminal of the battery. Secure it firmly with a screw.
- Connect Positive Terminal: Attach the positive cable of the spot welder to the positive terminal of the battery. Secure it firmly with a screw.
- Connect Sub-line Terminal: Plug the positive sub-line terminal into the designated port on the spot welder's circuit board.
IMPORTANT: Always ensure correct polarity. Connecting positive to negative or vice-versa will damage the device and may cause a safety hazard.
Device Layout and Display:


Operating Instructions
Power On/Off:
- To Turn On: In the stopped state, short press the ON/OFF (red button) to activate the spot welder function.
- To Turn Off: When the power is on, press and hold the ON/OFF (red button) to shut down the machine. The device also features a 5-minute automatic shutdown function if no operation is detected.
Adjusting Delay Time:
- In the power-on state, press the MENU (red button) until the delay number on the OLED display is highlighted.
- Press the V+/V- (black buttons) to adjust the delay time. The adjustable range is 0.5 seconds to 2.5 seconds. This setting determines the delay before the automatic spot welding pulse is output once the welding pen contacts the metal to be welded.
Adjusting Spot Welding Power:
- In the power-on state, press the MENU (red button) until the power supply number on the OLED display is highlighted.
- Press the V+/V- (black buttons) to adjust the power range. The range is typically 1-20 (representing 101 levels of adjustment). A larger value indicates higher spot welding power. Adjust appropriately for your material.
Performing a Spot Weld:
- Ensure the welding pens are clean and make good contact with the nickel strip and battery terminal.
- Place the nickel strip over the battery terminal where you intend to weld.
- Press the welding pen tips firmly onto the nickel strip.
- Wait for the set delay time to pass, after which the device will automatically output the welding pulse.
- Lift the welding pens. Inspect the weld for strength and quality.


Maintenance
- Keep the device clean and free from dust and debris.
- Store the spot welder in a dry environment when not in use.
- Regularly check the welding pens for wear and tear. Replace if necessary to ensure optimal performance.
- Ensure all connections are secure before each use.
Troubleshooting
- Poor Weld Quality: Check welding power settings, ensure good contact with the nickel strip, and verify the nickel strip thickness is within the recommended range (0.1-0.15mm).
- Device Not Turning On: Ensure the battery is charged or properly connected to an external power source. Check all cable connections.
- No Welding Pulse: Verify the delay time setting. Ensure the welding pens are making firm contact with the workpiece.
User Tips
- For most battery cells, applying 4 spot welds per connection point is generally sufficient for a strong bond.
- Experiment with different power and delay settings on scrap material to find the optimal configuration for your specific nickel strip thickness and battery type.
- Always ensure the welding pen tips are clean and sharp for consistent and strong welds.
Compliance Information
Manufacturer: Guangzhou Aicai Technology Co., Ltd.
Address: Room 709, No. 68, Gangwan Road, Huangpu District, Guangzhou
Certifications: CE, FC, RoHS
This product is manufactured in China.
For further details or support, please refer to the official product documentation or contact the manufacturer.
A user manual in PDF format is available for download: View User Manual (PDF)