retekess T131S

Contents

RETEKESS T131S Wireless Tour Guide System Receivers User Manual

Model: T131S Receivers (compatible with T130S Transmitter)

Brand: retekess

Introduction

The RETEKESS T131S is a wireless receiver designed to be part of a tour guide system, often paired with a T130S transmitter. This system is ideal for various applications such as excursions, church meetings, conferences, training sessions, museum tours, translation services, and factory visits. It provides clear, reliable audio communication, helping to overcome background noise and distance challenges.

Key features include a signal transmission distance of up to 100 meters (328 feet), approximately 20 hours of working time on a single charge, and 49 available channels to prevent interference.

RETEKESS T131S 10 Tour Guide Receivers
The RETEKESS T131S wireless tour guide system receivers.

Setup

1. Power On and Power Off

Transmitter (T130S)

  • **Power On**: Press and hold the power button (Power button icon) for 1 second to power on.
  • **Power Off**: Press and hold the power button (Power button icon) for 1 second to power off.

Receiver (T131S)

  • **Power On**: Press and hold the Play/Pause button (Play/Pause button icon) for 1 second to power on.
  • **Power Off**: Press and hold the Play/Pause button (Play/Pause button icon) for 1 second to power off.

2. Channel Setting (Transmitter T130S)

Channel setting is necessary when using multiple transmitters to avoid interference or when adding receivers to a group.

  1. In working mode, press and hold the (>) and (<) buttons simultaneously until the "1" icon disappears from the transmitter screen.
  2. Release the (>) and (<) buttons. The transmitter will enter channel setting mode.
  3. Press (>), (<), (+) or (-) buttons to select the desired channel (values from 01 to 49).
  4. Press and hold the power button (Power button icon) for 3 seconds until the channel ID flashes on the transmitter screen and the "1" icon disappears.
  5. Release the power button (Power button icon). The transmitter enters wireless channel synchronization mode.

3. Wireless Channel Synchronization Setting (Receiver T131S)

This method is used to set the channel ID for receivers when using a T130S transmitter with T131S receivers.

Transmitter Setting

  1. In power off mode, press and hold the (>) button with your left hand, then press the power button (Power button icon) for about 2 seconds with your right hand to turn on the transmitter.
  2. Release the power button (Power button icon) when the transmitter is powered on.
  3. Release the (>) button when the channel ID flashes on the screen. The transmitter enters channel setting mode.
  4. Press (>) or (<) button to select the desired channel.
  5. Press the power button (Power button icon) to confirm. The transmitter enters wireless channel synchronization mode.

Receiver Setting

  1. In power off mode, insert the earphone. Press and hold the (Previous Track button Previous Track button icon) button with your left hand, then press the Play/Pause button (Play/Pause button icon) with your right hand to turn on the receiver.
  2. Release the Play/Pause button (Play/Pause button icon) when the receiver is powered on.
  3. Release the (Previous Track button Previous Track button icon) button when the channel ID shows 00 on the receiver screen. The receiver will receive the sync signal. Once synchronized, the receiver's channel will change to the same channel as the transmitter. (Note: This step must be done while the transmitter is in wireless channel synchronization mode).
  4. Turn off the transmitter, then turn it on. The transmitter will now work with the paired receivers.

4. Manual Set Receiver Channel ID

  1. In power off mode, press and hold the (Next Track button Next Track button icon) button with your right hand, then press the Play/Pause button (Play/Pause button icon) button with your left hand to turn on the receiver.
  2. Release the Play/Pause button (Play/Pause button icon) button when the receiver is powered on.
  3. Release the (Next Track button Next Track button icon) button when the channel ID changes on the screen.
  4. Press (Next Track button Next Track button icon) or (Previous Track button Previous Track button icon) button to select the desired channel ID.
  5. Press the Play/Pause button (Play/Pause button icon) button to confirm.

Operating Instructions

1. Transmitter (T130S) Functions

Mute Function

  • In working mode, press the (>) or (+) button. The transmitter enters mute mode, and a mute icon appears on the transmitter screen while the "1" icon disappears. Simultaneously, an "X" icon appears on the receiver screen.
  • Press the (>) or (+) button again to return to normal working mode. The "1" icon reappears on the transmitter screen, and the "X" icon disappears from the receiver screen.

One-Key Shutdown Function

  • In working mode, press and hold the (>) or (-) button for about 5 seconds until the OFF icon flashes on the transmitter screen and the "X" icon disappears. All receivers paired with this transmitter that are within range will power off.
  • To exit this mode, short press any key on the transmitter, or long press and hold the power button (Power button icon) to power off.

Interface Description

The transmitter has two jacks at the bottom: the MIC microphone jack on the left and the AUX audio input jack on the right.

  • **Note**: Do not insert cables into the wrong interface. If the microphone is plugged into the AUX jack, there will be no sound.
Back view of the RETEKESS T131S transmitter showing model, voltage, frequency, and FCC ID
Back view of the T130S Transmitter with label.

2. Receiver (T131S) Functions

Volume Setting

  • In working mode, press the (Next Track button Next Track button icon) or (Previous Track button Previous Track button icon) button to adjust the volume (0 to 9 levels).
  • **Note**: Volume cannot be adjusted while the receiver is in signal seek mode (a magnifying glass icon appears on the receiver screen).

Earphone Usage

The system includes D-shaped earphones that are compatible with both left and right ears, offering flexibility and comfort for extended wear.

D-shaped earphone design for universal left and right ear wear
D-shaped earphone design for universal left and right ear wear.
D-shaped earphone with 3.5mm jack
The D-shaped earphone with a 3.5mm jack.

Maintenance

1. Battery Precautions

  • If the device is not used for a long time, please charge it every 3 months to prevent battery damage due to over-discharge.
  • The built-in lithium battery can be damaged by over-discharge.

2. Charging Box Precautions

  • **Working Voltage**: AC90V-250V.
  • Please remove the foam from the charging box before charging.
  • Keep the cover of the charging box open when charging.
  • It takes approximately 4 hours for a full charge.
Battery capacity and working hours comparison for T130S-T131S and T130-T131 models
Battery capacity and working hours comparison for T130S-T131S and T130-T131 models.

Troubleshooting & Safety

1. Common Issues

  • **No Sound from Microphone**: Ensure the microphone is plugged into the MIC jack, not the AUX jack, on the transmitter.
  • **Interference**: If experiencing interference, ensure each transmitter is set to a different channel.
  • **Volume Not Adjustable**: Volume cannot be adjusted when the receiver is in signal seek mode.

2. RF Energy Exposure and Product Safety Guide

ATTENTION!

Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

This radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. RF energy, when used improperly, can cause biological damage.

All Retekess radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. Manufacturers also recommend specific operating instructions to users of the radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it.

Please refer to http://www.who.int/en/ for more information on RF energy exposure and how to control your exposure to assure compliance with established RF exposure limits.

Local Government Regulations

When radios are used as a consequence of employment, Local Government Regulations require users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Retekess radio has an RF Exposure Product Label. Also, your Retekess user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements.

Radio License (if appropriate)

Governments keep the radios in classification, business radios operate on radio frequencies that are regulated by the local radio management departments (FCC, ISED, OFCOM, ANFR, BFTK, Bundesnetzagentur...). To transmit on these frequencies, you are required to have a license issued by them. The detailed classification and the use of your radios, please contact the local government radio management departments.

Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.

Unauthorized Modification and Adjustment

Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority granted by the local government radio management departments to operate this radio and should not be made. To comply with the corresponding requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services.

3. FCC Requirements

  • This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
    1. This device may not cause harmful interference, and
    2. This device must accept any interference received, including interference that may cause undesired operation.
  • (If applicable) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.

4. CE Requirements

  • (Simple EU declaration of conformity) Henan Eshow Electronic Commerce Co.,Ltd declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU; the full text of the EU declaration of conformity is available at the following internet address: www.retekess.com.
  • **Disposal**: The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area.

5. IC Requirements (Licence-exempt radio apparatus)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

6. RF Exposure Information (if appropriate)

  • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio, and the antenna gain shall not exceed the specified gain by the manufacturer declared.
  • DO NOT transmit for more than 50% of total radio use time, more than 50% of the time can cause RF exposure compliance requirements to be exceeded.
  • During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so.
  • The device complies with RF specifications when the device used at 5mm from your body. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided.
  • DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

7. Avoid Choking Hazard

Choking hazard warning iconSmall Parts. Not for children under 3 years.

8. Protect Your Hearing

Warning icon**WARNING**

  • Use the lowest volume necessary to do your job.
  • Turn up the volume only if you are in noisy surroundings.
  • Turn down the volume before adding headset or earpiece.
  • Limit the amount of time you use headsets or earpieces at high volume.
  • When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
  • Use care with the earphone; excessive sound pressure from earphones and headphones can cause hearing loss.

Note: Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect.

9. Avoid Burns

Warning icon**WARNING**

Antennas

  • Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with the skin when the radio is in use, a minor burn can result.

Batteries (If appropriate)

  • When conductive material such as jewelry, keys, or chains touch exposed terminals of the batteries, it may complete an electrical circuit (short circuit the battery) and become hot, causing bodily injury such as burns. Exercise care in handling any battery, particularly when placing it inside a pocket, purse, or other container with metal objects.

Long Transmission

  • When the transceiver is used for long transmissions, the radiator and chassis will become hot.

10. Safety Operation

Warning icon**WARNING**

Forbid

  • Do not use charger outdoors or in moist environments; use only in dry locations/conditions.
  • Do not disassemble the charger; this may result in risk of electrical shock or fire.
  • Do not operate the charger if it has been broken or damaged in any way.
  • Do not place a portable radio in the area over an airbag or in the airbag deployment area. The radio may be propelled with great force and cause serious injury to occupants of the vehicle when the airbag inflates.

To Reduce Risk

  • Pull by the plug rather than the cord when disconnecting the charger.
  • Unplug the charger from the AC outlet before attempting any maintenance or cleaning.
  • Contact Retekess for assistance regarding repairs and service.
  • The adapter shall be installed near the equipment and shall be easily accessible.
  • Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
  • The plug is considered as the disconnect device of the adapter.
  • The operating temperature of the EUT can't exceed the specified range.

11. Approved Accessories

Warning icon**WARNING**

  • This radio meets the RF exposure guidelines when used with the Retekess accessories supplied or designated for the product. Use of other accessories may not ensure compliance with the RF exposure guidelines and may violate regulations.
  • For a list of Retekess-approved accessories for your radio model, visit the following website: http://www.Retekess.com.

Specifications

Transmitter (T130S)

FeatureSpecification
Frequency Range195-216MHz
Channels49CH
Working VoltageDC 3.7V
Output Power18dBm
Mic/Aux input3.5mm
Frequency Response50-18000Hz
SNR80dB (Typical)
Image rejection ratio≥90dB
T.H.D<0.3%
Operating Range100m (line of sight)
Battery Capacity4200mAh
Battery Run TimeAbout 20 hours typical
Weight140g / 0.3lb
Size205 x 60 x 20mm / 8 x 2.3 x 0.7 in

Receiver (T131S)

FeatureSpecification
Frequency Range195-216MHz
Channels49CH
Working VoltageDC 3.7V
Earphone Jack3.5mm
Frequency Response50-18000Hz
SNR80dB (Typical)
Image rejection ratio≥90dB
T.H.D<0.3%
Operating Range100m (line of sight)
Battery Capacity900mAh
Battery Run TimeAbout 20 hours typical
Weight45g / 0.1lb
Size73x 42 x 12mm / 2.8 x 1.6 x 0.5 in
Comparison table of Retekess tour guide system models with features, working frequency, distance, and standby time
Comparison of different Retekess tour guide system models.

User Tips

  • This product is highly versatile and can be effectively used as a guide system in various settings, including churches, museums, and factories.
  • Enjoy seamless wireless communication across 49 channels, providing flexibility and minimizing interference.
  • The receivers offer an impressive working time of approximately 20 hours, ensuring long-lasting performance for full-day events or tours.

Warranty and Support

Guarantee

This guarantee card should be kept by the user; no replacement if lost.

Most new products carry a two-year manufacturer's warranty from the date of purchase.

The user can get warranty and after-sales service as below:

  • Contact the seller where you buy.
  • Products Repaired by Our Local Repair Center.

For warranty service, you will need to provide a receipt proof of purchase from the actual seller for verification.

Exclusions from Warranty Coverage:

  1. To any product damaged by accident.
  2. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs.
  3. If the serial number has been altered, defaced, or removed.

Contact Information

Henan Eshow Electronic Commerce Co., Ltd.

Address: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China

Facebook: facebook.com/Retekess

E-mail: support@retekess.com

Web: www.retekess.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.