WINXU 250W/350W S886 Controller Kit

Contents

User Manual: E-Bike Brushless Motor Controller & S886 LCD Display Kit

Model: 250W/350W, S886 / G51 / S866 / TF-100

Brand: WINXU

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your WINXU E-Bike Brushless Motor Controller and S886 LCD Display Kit. This universal kit is designed for electric bicycle and scooter repair and conversion, offering efficient control and clear data display.

For a comprehensive guide, a PDF version of this manual is available: User Manual (PDF).

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Always disconnect the battery power supply before installing or performing maintenance on the controller.
  • Do not work with the power on, as it may easily damage the equipment and pose a safety risk.
  • Ensure all connections are secure and correctly wired to prevent short circuits, overheating, and damage.

3. Specifications

FeatureDescription
Product TypeBrushless Motor Controller & LCD Display Kit
Brand NameWINXU
OriginMainland China
Input Voltage24V / 36V / 48V
Power250W / 350W
Low-voltage Protection (24V-36V)19V / 30V
Low-voltage Protection (36V-48V)30V / 41V
Controller SizeApprox. 8.5 x 5.2 x 3 cm (3.35 x 2.05 x 1.18 inches)
LCD Display ModelS886 / G51 / S866 / TF-100 (S886 is featured)
Display SizeApprox. 8 x 5 cm (3.15 x 1.97 inches)
MaterialPlastic + LCD + Metal
Waterproof RatingRainproof
WeightApprox. 332g

Package Contents:

  • 1 x LCD Display (S886 model shown)
  • 1 x Brushless Motor Controller

4. Setup & Installation

4.1 Pre-use Preparation

Before installing the controller, always disconnect the battery power supply. Do not attempt installation with the power on, as this can damage the equipment and pose a safety risk.

4.2 Understanding the Wiring Diagram

Carefully review the wiring diagram below and familiarize yourself with the function of each connector before proceeding with installation.

Detailed wiring diagram for the WinXu Brushless Dual-mode Controller, showing connections for battery, light power, low level brake, EABS, PAS sensor, auto-detection, throttle, power lock, LCD display, motor hall, and motor phase wires.

Figure 1: WinXu Tech Brushless Controller Wiring Diagram

Each cable is color-coded for specific functions:

  • Red: Power positive electrode
  • Black: Power negative electrode
  • Yellow: Power output
  • Brown: Lamp positive electrode
  • White: Lamp negative electrode
  • Blue: Indicator signal
  • Green: Signal receive

4.3 Connector Function Introduction and Installation Steps

  1. Motor Phase Wire: Connect the three thick phase wires (yellow, green, blue) from your motor to the corresponding controller wires according to the color code. Ensure a secure connection as these wires carry significant current.
  2. Motor Hall Sensor: Connect the motor Hall sensor. This controller uses a 6-wire Hall sensor. Red, yellow, and blue are Hall signal wires; red and black are working voltage; white is the motor speed signal. Connect according to correct colors. If your motor has a 5-wire Hall sensor, ignore the white speed signal cable; the controller will automatically obtain the motor speed signal from the Hall signal cable.
  3. LCD Display (UART Protocol): This 5-pin connector is for the LCD display. Red and black are for operating voltage, blue for controller power control, green is RX, and yellow is TX.
    S886 LCD display with integrated thumb throttle and wiring.

    Figure 2: S886 LCD Display with Thumb Throttle

  4. Power Lock (Key Lock): Connect your bicycle's key lock switch to this connector if available. If your bicycle does not have a key lock, this connector can be ignored.
  5. Throttle: This connector is for a Hall throttle (thumb or twist type), which receives a signal voltage of 1.1-4.2V. Red and black are operating voltage, and white is the Hall signal. Ensure correct connection.
  6. PAS Sensor (Pedal Assist System): This controller uses a magnetic pulse type PAS sensor. Red and black are power voltage wires, and blue is the pulse signal cable. Ensure compatibility with universal type PAS sensors.
  7. EABS (Electronic Automatic Braking System): If your scooter uses an EABS type brake, connect it here. EABS brakes are Hall brake systems. Do not use this connector for low-level brakes.
  8. Low-Level Brake: This is a power-off braking system that cuts motor power when brakes are applied. The black cable is negative, and the white cable is the brake signal. Connect correctly if your brake is a low-level type with 2 cables.
  9. Light Power: This connector outputs battery voltage for devices like headlights, brake lights, horns, and USB chargers. Yellow is positive, black is negative.
  10. Battery: This is the device's power supply. Connect positive and negative terminals correctly. Incorrect connection can cause short circuits, overheating, or damage. Connect the battery last, after checking all other components for proper connection and no short circuits. Double-check for reverse polarity.
  11. Automatic Detection (Self-Learning Cable): This connector is used for motor matching. After initial installation, use this connector:
    1. Turn on the device, lift the motor hub, and plug in this connector.
    2. The motor will start driving. If it drives in the opposite direction, disconnect and reconnect the connector to change direction.
    3. Once the motor drives in the correct direction without vibration, disconnect the self-learning cable. You can then test riding normally.

5. Operating Instructions

5.1 LCD Display Functions (S886)

The S886 LCD display provides clear state and data information, including speed, distance (ODO), battery level, and error codes. The backlight ensures visibility in dim environments. Buttons allow for quick operation.

Close-up of the S886 LCD display showing speed, battery, and odometer readings.

Figure 3: S886 LCD Display Interface

  • Power-on Password: The display allows setting a power-on password for security.
  • Light Control: Control connected lights directly from the display.
  • Cruise Function: Activate and manage the cruise control feature.
  • Boost Function: Utilize the boost feature for additional power.
  • Speed Gears: The vehicle speed can be divided into 3, 5, or 9 optional gear positions. The thumb throttle can be configured to operate with or without these gears.
  • Odometer (ODO): The LCD display features an odometer that memorizes the lifetime distance.

5.2 Initial Setup and E07 Error

After the first installation, if the controller has not completed motor matching and parameter detection, the display will show the E07 error code (Motor failure). To resolve this:

  1. Complete the motor matching operation using the self-learning cable as described in Section 4.3, step 11.
  2. Once motor matching is complete, use the throttle and high-speed gear to drive the motor at high speed.
  3. The controller will detect motor parameters and status. If no fault is detected during high-speed driving, the E07 error code will automatically clear.
  4. If E07 persists, it indicates insufficient driving speed or a fault with the motor or motor hall sensor. Check these components.

6. Troubleshooting: LCD Error Codes

The LCD display provides error codes to help diagnose issues. Refer to the table below for common error codes and their meanings:

Error CodeDescription
E02Brake fault
E03PAS sensor fault
E046KM/H cruise mode fault
E05Real-time cruise fault
E06Battery undervoltage
E07Motor failure (See Section 5.2 for resolution)
E08Throttle fault
E09Controller failure
E10Communication signal reception failure
E11Communication signal transmission fault
E12BMS communication fault
E13Headlight fault

7. Maintenance & Storage

7.1 Cleaning

  • Turn off the device before cleaning.
  • Use a soft, lint-free cloth for cleaning. Avoid using harsh chemicals or abrasive materials.

7.2 Storage

  • Store the device in a dry place at room temperature (15°C - 35°C / 59°F - 95°F).
  • For long-term storage, if not used for a prolonged period, charge the device to 50% capacity every 3 months to maintain battery health.

8. User Tips

  • Programming: While the manual doesn't detail programming steps, the LCD display allows setting a power-on password and configuring speed gears (3/5/9 options). Refer to the display's specific menu for these adjustments.
  • Odometer Memory: The S886 LCD display's odometer (ODO) function will memorize the lifetime distance, even after power cycles.
  • Compatibility: This kit is designed for universal E-bike and scooter repair and conversion. Ensure your motor and other components are compatible with the specified voltage and power ratings.

9. Warranty & Support

For technical support, warranty claims, or further inquiries, please contact the manufacturer:

  • Manufacturer: ShenZhne Winxu Technology Co,.Ltd
  • E-mail: Winxutech@163.com
  • Tel: +86-15814065441

For EU customers, the authorized representative is:

  • Name: Vermilion Bird OU
  • E-mail: vermilionbird.eu@outlook.com

10. Disposal & Recycling

This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.