BAOFENG UV-9R Pro V2

Contents

Baofeng UV-9R Pro V2 IP68 Waterproof Walkie Talkie

Instruction Manual

1. Introduction and Safety Information

Thank you for purchasing the Baofeng UV-9R PRO Series Amateur Radio. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.

1.1 Regulations and Safety Warnings

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

ATTENTION! When programming the radio, always start by reading the factory software data before rewriting. Use a programming cable with a PC to program authorized frequencies, bandwidth, and power levels in compliance with FCC (or EU) license certifications.

ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

RF Exposure Compliance and Control Guidelines

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany the device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.
  • Transmit no more than the rated duty factor of 50% of the time. Press the Push-to-Talk (PTT) key to transmit; release it to receive.
  • Keep the radio unit at least 2.5cm away from your face.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness, or use the correct clip.
  • Use of non-approved antennas, batteries, and accessories may cause the radio to exceed FCC RF exposure guidelines.

Operating Prohibitions

To protect against property loss, bodily injury, or death, observe the following:

  1. Do not operate the product in locations containing fuels, chemicals, or explosive materials unless it is an approved Ex-protection model.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near medical or electronic equipment vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where wireless communication equipment is prohibited.

2. Main Features

The Baofeng UV-9R Pro V2 offers a robust set of features for reliable communication:

  • Frequency Range: FM radio 76-108 MHz; AM aviation band 108-136MHz (RX); VHF1: 136-174MHz (RX&TX); UHF1: 400-520MHz (RX&TX); UHF2: 350-390MHz (RX).
  • Tri-Power Output: High, Mid, and Low power selection to meet different needs.
  • IP68 Waterproof: Enhanced waterproof and dustproof capabilities (not for diving).
  • Type-C Charging: Supports direct Type-C battery charging for convenience.
  • Dual Band & Dual Display: VHF and UHF bands with simultaneous display.
  • Memory Channels: Up to 128 memory channels.
  • SOS Emergency Function: For urgent situations.
  • VOX Function: Hands-free operation.
  • Flashlight: Built-in LED flashlight.
  • CTCSS/DCS Codes: 50 CTCSS tones and 210 DCS codes for privacy.
  • Keypad Lock: Prevents accidental key presses.
  • PC Programmable: Can be programmed via PC.
Baofeng UV-9R Pro V2 with IP68 Waterproof and Tri-Power features

Figure 1: Baofeng UV-9R Pro V2 highlighting IP68 Waterproof, Tri-Power, and Type-C charging.

Baofeng UV-9R Pro V2 features including Tri-Power, SOS, Flashlight, PC Programmable, Anti-dust and rain, Hands Free, CTCSS

Figure 2: Overview of key features including Tri-Power, SOS, Flashlight, and programmability.

3. Package Contents

The standard package includes the following items:

  • 1 x Portable Radio (UV-9R Pro V2)
  • 1 x Antenna
  • 1 x Li-Ion Battery Pack
  • 1 x Type-C Charger (or Desktop Charger with Wall Adaptor, depending on variant)
  • 1 x Belt Clip
  • 1 x Lanyard (Sling)
  • 1 x User's Manual (Paper version)

If any item is missing, please contact your BAOFENG dealer.

Accessories Parameters table showing Machine, Antenna, Battery, Type-C Charger, Clip, Lanyard, User's Manual

Figure 3: Included accessories and basic specifications.

4. Radio Overview

4.1 Buttons and Controls

Diagram of Baofeng UV-9R Pro V2 with numbered parts: 1. Antenna, 2. PTT, 3. SK-Side key1/F, 4. SK-Side key2/M, 5. keypad, 6. Knob (NO/OFF,Volume), 7. Speaker, 8. Accessory Jack, 9. Microphone, 10. LCD, 11. Strap Buckle, 12. Battery Latch, 13. Flashlight, 14. LED Indicator. Dimensions: 65*41.5*133.8mm.

Figure 4: Labeled diagram of the radio's components and controls.

  1. Antenna: For transmitting and receiving signals.
  2. PTT (Push-to-Talk): Press to transmit, release to receive.
  3. SK-Side key1/F: Function key 1.
  4. SK-Side key2/M: Function key 2.
  5. Keypad: Numeric and function keys for input.
  6. Knob (NO/OFF, Volume): Rotate to power on/off and adjust volume.
  7. Speaker: Audio output.
  8. Accessory Jack: For external speaker/microphone.
  9. Microphone: Audio input.
  10. LCD Display: Shows frequency, channel, menu settings, and status.
  11. Strap Buckle: Attachment point for lanyard.
  12. Battery Latch: Secures the battery pack.
  13. Flashlight: LED light for illumination.
  14. LED Indicator: Red for transmission, green for reception.

4.2 LCD Display Indications

The LCD display provides important information about the radio's status:

  • CT/DCS Symbols: Indicate if CTCSS or DCS codes are set for transmit (tx) or receive (rx).
  • Received Signal Strength: Bar graph indicating signal strength.
  • Low Power Selection: Icon displayed when low power is selected.
  • Dual Watch: Icon displayed when Dual Watch function is active.
  • VOX Function: Icon displayed when VOX is enabled.
  • Positive/Negative Shift: Icons indicate positive or negative frequency shift for repeaters.
  • Keypad Lock: Icon indicates keypad is locked.
  • Battery Level Indicator: Shows remaining battery charge. Blinks when low.
  • Channel Number: Displays the stored channel number.
  • Frequency/Channel Name: Shows the current operating frequency or channel name.

4.3 Main Keypad Controls

  • [SOS] Key: Long press to activate/deactivate alarm function.
  • [SK1] Key: Short press to turn FM radio on/off. Long press for One-touch frequency search.
  • [SK2] Key: Short press to turn flashlight on (first press for steady, second for strobe, third for off). Long press to activate Monitor function.
  • [MENU] Key: Enters MENU functions, confirms selections. Press and hold from off state to switch between frequency (VFO) and channel (MR) modes.
  • [▲]/[▼] Keys: Navigate menu items, change frequency/channel rapidly (long press), change scan direction.
  • [*SCAN] Key: Short press for reverse function. Long press to activate SCAN function.
  • [#] Key: Short press to switch between High/Mid/Low output power. Long press (2 seconds) to lock/unlock keypad.
  • [0SQL] Key: Press and hold for 2 seconds to display battery voltage.

5. Installation of Accessories

5.1 Installing/Removing the Antenna

  • Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

5.2 Installing the Belt Clip

  1. Install Fixing Head: Install the belt clip fixing head into the slot on the back of the radio and tighten the screws.
  2. Insert Rotating Belt Clip: Slide the fixed head of the machine along the guide of the rotating back clip until it clicks.
  3. Remove Belt Clip: Use the key to press the disassembly engine upwards until it releases, then push the belt clip with your thumb to remove.

5.3 Installing the Battery Pack

Before attaching or removing the battery, ensure the radio is turned off by rotating the power/volume knob counter-clockwise.

  1. Insert the two protrusions on the front of the battery into the notches on the bottom of the radio.
  2. Press the tail of the battery toward the radio until you hear a "click".

5.4 Removing the Battery Pack

Turn off the radio. Lift the battery push button at the end of the battery to disengage the tail of the battery from the intercom and remove the battery backwards.

5.5 Installing the Additional Speaker/Microphone (Optional)

  1. Use a flat-blade screwdriver to unscrew the screw at the lower end of the cover counterclockwise to remove the headset cover.
  2. Insert the protruding part of the lower end of the headset into the slot.
  3. Align the nut on the upper end of the headset with the corresponding threaded hole of the transceiver and rotate it clockwise until it is tightened.

NOTE: Please install accessories correctly; otherwise the waterproof performance of this product may be affected.

6. Charging the Battery

The Li-ion battery pack is not fully charged at the factory. Please charge it before first use. For optimal performance, fully charge and discharge the battery two or three times.

6.1 Charger Supplied

Always use the specified charger provided by Baofeng. Using other chargers may cause explosion or personal injury. If the radio displays 'low battery' with a voice prompt, charge the battery.

Type-C Fast Charging, showing the Type-C port on the battery and charging from a power bank or car charger.

Figure 5: Type-C direct charging capability.

Two Charging Methods: Type-C Battery Direct Charging and Fast Charging (desktop charger).

Figure 6: Two available charging methods: Type-C direct and desktop charger.

6.2 Use Caution with the Li-ion Battery

  • Do not short the battery terminals or throw the battery into a fire.
  • Do not attempt to remove the casing from the battery pack.
  • Charge the battery between 5°C-40°C (40°F - 105°F).
  • Turn off the radio before inserting it into the charger.
  • Do not interrupt the charging cycle until the green light is on.
  • Do not recharge a fully charged battery.
  • Dry a damp battery or radio before charging.

6.3 How to Charge

  1. Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange.
  2. Plug the battery or the radio into the charger. Ensure good contact between battery terminals and charging terminals. The indicator light turns red.
  3. Charging takes approximately 2-5 hours. When the lamp lights green, charging is complete.

6.4 LED Indicator Status

STATUSLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
Trouble (e.g., battery too warm, short-circuited)Red blinks fast for a long time

6.5 How to Store the Battery

  • Store the battery at approximately 80% discharged.
  • Keep it in a low temperature and dry environment, away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.

7. Basic Operations

7.1 Power On/Off

  • To Turn On: Rotate the Volume/Power knob clockwise until you hear a "click". The radio will display a message or flash the LCD for about one second, then display a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • To Turn Off: Rotate the Volume/Power knob counter-clockwise all the way until you hear a "click".

7.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease volume.

7.3 Making a Call

  • Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will be on during transmission.
  • Frequency Mode Call: In frequency mode, enter the desired frequency, then hold down the [PTT] key to transmit.
  • Receiving a Call: When you release the [PTT] key, you can answer without any action. The green LED will be on during reception.

NOTE: For best reception volume, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

7.4 Channel Selection

The radio operates in two modes: Frequency (VFO) mode and Channel (MR) mode.

  • Frequency (VFO) Mode: Used for temporary frequency assignments or quick field programming. You can navigate frequencies using the [▲]/[▼] keys or input directly via the numeric keypad.
  • Channel (MR) Mode: More practical for everyday use with pre-programmed channels. Navigate channels using the [▲]/[▼] keys.

WARNING! Transmitting on unauthorized frequencies is illegal and can result in fines or imprisonment. Always ensure you have the proper license for the frequencies you operate on.

8. Advanced Features

8.1 Frequency Scanning

This function scans frequencies:

  1. In frequency mode, long press [*SCAN] for more than 2 seconds. The radio will start scanning according to the set frequency step.
  2. Change scanning direction with [▲]/[▼] keys.
  3. Press any key to stop scanning.

8.2 Channel Scanning

This function scans channels:

  1. In channel mode, long press [*SCAN] for more than 2 seconds. The radio will start scanning the channels.
  2. Change scanning direction with [▲]/[▼] keys.
  3. Press any key to stop scanning.

8.3 Search CTCSS/DCS Code

This function allows searching and storing CTCSS/DCS codes used by other radios:

  1. In frequency mode, press [MENU]+[1][1].
  2. Press [MENU] again.
  3. Press [*SCAN]; "CT" will blink on the display.
  4. When another radio transmits, the display will show the CTCSS/DCS code.
  5. After searching, the radio will beep and stop scanning.
  6. Press [MENU] to confirm and store, or [PTT]/[EXIT] to return to standby mode.

8.4 Cursor ▲/▼ Conversion (A/B)

Directly press [EXIT] to move the cursor up and down to modify or confirm parameters. In frequency or channel mode, [EXIT] shifts between main channel A and sub-channel B.

8.5 High/Mid/Low Power Fast Selection

In channel mode, press [#] to quickly switch between high, mid, and low power output.

8.6 Keypad Lock

Long press [#] for more than 2 seconds to lock/unlock the keypad.

8.7 FM Radio

The radio can listen to FM radio from 65-108MHz.

  1. In frequency or channel mode, press [SK1] to turn on the FM radio.
  2. Select the desired frequency with [▲]/[▼] keys or input directly. Alternatively, press [*SCAN] to automatically search for a station.
  3. Press [SK1] to exit FM radio.

8.8 Flashlight

Press [SK2] to turn on the flashlight. Press again for strobe mode, and a third time to turn it off.

LED Flashlight feature, showing radio illuminating a dark environment.

Figure 7: The built-in LED flashlight for dark environments.

8.9 TX 1000Hz, 1450Hz, 1750Hz, 2100Hz Repeaters Tone

Press [PTT] + [SOS] to send a 1750Hz repeater tone. This is useful for communications through repeaters. Other tones (1000Hz, 1450Hz, 2100Hz) can be selected via Menu No.41.

8.10 Manual Programming (Channels Memory)

The UV-9R PRO features 128 memory channels. Each channel can store receive and transmit frequencies, transmit power, signaling information, bandwidth, and a six-character alphanumeric identifier.

Example: Programming a Channel Repeater Offset with CTCSS Tone

To program a new memory in Channel 10 with RX = 432.000 MHz, TX = 437.000 MHz (a +5 Offset), and TX CTCSS tone 123.0:

  1. Turn off the radio.
  2. Hold [MENU] to turn on the radio, entering frequency mode. The channel number on the right will disappear.
  3. Press [MENU] [2][8] [MENU] [1][0] [MENU] [EXIT] to delete prior data in Channel 10.
  4. Press [MENU] [1][3] [MENU] 123.0 [MENU] [EXIT] to select the desired TX encode tone.
  5. Enter RX frequency (e.g., 432000).
  6. Press [MENU] [2][7] [MENU] [1][0] [MENU] then [EXIT]. RX has been added.
  7. Enter TX frequency (e.g., 437000).
  8. Press [MENU] [2][7] [MENU] [1][0] [MENU] then [EXIT]. TX has been added.
  9. Turn off the radio, then hold [MENU] to return to MR mode. The channel number will reappear.

8.11 Repeaters Programming

To program repeaters, you need to know the transmit and receive frequencies and be authorized to use them.

  1. Turn off the radio. Hold [MENU] to turn on the radio, entering frequency (VFO) mode.
  2. Use the numeric keypad to enter the repeater's output (your receiving) frequency.
  3. Press [MENU] to enter the menu.
  4. Enter [2][6] for frequency offset. Press [MENU] to select.
  5. Enter the specified frequency offset. Press [MENU] to confirm and save.
  6. Enter [2][5] for offset direction. Use [▲]/[▼] keys to select + (positive) or - (negative) offset. Press [MENU] to confirm and save.
  7. (Optional) Save to memory (see Manual Programming) or set up CTCSS.
  8. Press [EXIT] to exit the menu.

This function allows the radio to act as a receiver and search for an effective frequency.

  1. Press and hold the [SK1] key. The screen will display "SEARCH UHF".
  2. If a transmitter continues to transmit and the unit receives a strong, stable signal, the received frequency will be displayed. If CTCSS or DCS is present, its value will be shown; otherwise, "NONE" is displayed.
  3. Press [MENU] to save the Search frequency and CTCSS or DCS to a channel.

Note: During frequency Search, press the [#] key to switch between UHF or VHF bands.

10. Technical Specifications

ParameterValue
Frequency Range144.0-148.0 & 420.0-450.0MHz (Tx, FCC Rule parts 97 to USA users)
136.0-174.0 & 400.0-480.0MHz (Scanning Receiver, FCC Rule parts 15B to USA users)
144.0-146.0 & 430.0-440.0MHz (Tx/Rx. Limited to EU users)
Memory Channel128 Groups
Operation VoltageDC 7.4 V ±10%
Battery Capacity1800mAh (Li-Ion)
Transmission Current≤1800mA
Receive Sensitivity0.25µV (12dB SINAD)
Power Output1W @16 ohms (Tri-Power: 5W-10W)
Receive Current≤380mA
Rated Audio Distortion≤5%
Dimensions173*100*95mm (Radio: 65*41.5*133.8mm)
Waterproof / Water-ResistantIP45 (IP68 for Pro V2)
Maximum Range5km-10km

ATTENTION! Operating frequency is divided into transmit and receive frequencies; please comply with the Radio Regulations in your country or territory.

EU-TYPE EXAMINATION (MODULE B) CERTIFICATE for Radio Equipment Directive (RED) 2014/53/EU.

Figure 8: EU-Type Examination Certificate for the transceiver.

11. Troubleshooting Guide

If you encounter any issues with your radio, refer to the table below for common problems and solutions.

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery improperly installed, battery run out, poor battery contact.Reattach/replace battery, clean contacts.
Weak or intermittent voice during receiving.Low battery, low volume, loose antenna, blocked speaker.Recharge battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Inconsistent frequency/signaling type, too far from others, interrupted by other radios.Verify TX/RX frequency/signaling, move closer, change frequency/squelch.
Hear unknown voices or noise.Too far from others, unfavorable position (blocked by buildings/underground), external interference.Move closer, move to open area, stay away from interfering equipment.
Radio keeps transmitting.VOX turned on or headset not in place.Turn off VOX, check headset.

NOTE: If these solutions do not resolve your problems, please contact your dealer for technical support.

12. User Tips

  • Output Power: The output power of this walkie-talkie varies from 5W to 10W, allowing flexibility based on communication needs.
  • Maximum Range: The maximum range for this device is typically between 5km and 10km in open areas. In urban environments, the range may be 2-5km due to obstructions.
  • Programming: The radio supports CHIRP software and is compatible with Mac, Windows XP/7/8/8.1/10 systems for programming.
  • Inter-brand Communication: This walkie-talkie can communicate with other brands of walkie-talkies as long as the operating frequencies are the same.
Practical Application scenarios: Hotel reception, Mountaineering, Construction site, Hunting, Self-driving tour, Fishing.

Figure 9: Various practical applications for the Baofeng UV-9R Pro V2.

13. Warranty and Support

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company.

13.1 Declaration of Conformity

Baofeng hereby declares that the radio equipment type listed in Appendix B (Technical Specifications) is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.Baofeng.cn/download.asp?EnBigClassName=EU+DOC&EnSmallClassName=&page=3.

13.2 Disposal of Electronic and Electric Equipment

Products with the symbol of a crossed-out wheeled bin cannot be disposed of as household waste. Electronic and Electric Equipment should be recycled at a facility capable of handling these items and their waste products. In EU countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.

13.3 Conditions of Use

ATTENTION: The band of frequencies on which this device operates is administered by limitations and/or permissions for their usage. In EU Countries, operators must consult the entrusted authorities and possess a license or a frequency assigned to them by their respective competent authority.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.