NISSEI RX-103

Contents

NISSEI RX-103 SWR/Watt Meter

Instruction Manual

1. Product Overview

The NISSEI RX-103 is a high-precision SWR/Watt meter designed for measuring Standing Wave Ratio (SWR) and power (Forward and Reflected) in radio frequency systems. It operates within a frequency range of 1.6 to 60 MHz and can measure power up to 2000 Watts. Its large cross-dial display allows for direct reading of SWR and power without the need for calibration.

Front view of the NISSEI RX-103 SWR/Watt Meter
Front view of the NISSEI RX-103 SWR/Watt Meter, showing the analog display, range selector, and AVG/PEP button.

2. Setup

Follow these steps to set up your NISSEI RX-103 SWR/Watt Meter:

  1. Power Connection: Connect the provided 13.8V DC wire to the 'DC 13.8V' input port on the rear panel of the meter. Ensure the power source provides stable 13.8V DC.
  2. Antenna Connection: Connect your antenna cable to the 'ANT' SO-239 connector on the rear panel.
  3. Transceiver Connection: Connect your radio transceiver's output to the 'TX' SO-239 connector on the rear panel.
  4. Placement: Place the meter on a stable, flat surface, ensuring adequate ventilation.
Rear view of the NISSEI RX-103 SWR/Watt Meter showing connections
Rear view of the NISSEI RX-103 SWR/Watt Meter, clearly showing the TX and ANT SO-239 connectors, DC 13.8V power input, serial number, and CE RoHS markings.

3. Operating Instructions

The NISSEI RX-103 allows for direct measurement of SWR, Forward (FWD) power, and Reflected (REV) power. No calibration is required.

  1. Power On: Ensure the meter is correctly powered via the 13.8V DC input.
  2. Select Power Range: Use the 'RANGE' knob on the front panel to select the appropriate power range (x1, x10, or x100) based on your transceiver's output power. For example, if your transceiver outputs 100W, select the 'x10' range. The maximum measurable power is 2000W.
  3. Select Measurement Mode (AVG/PEP): Press the orange button to toggle between AVG (Average Power) and PEP (Peak Envelope Power) measurement modes.
  4. Transmit: Key your transceiver to transmit. The meter's needles will indicate the FWD (Forward) power, REV (Reflected) power, and SWR simultaneously.
  5. Readings:
    • FWD (Forward Power): Indicates the power transmitted from your transceiver to the antenna.
    • REV (Reflected Power): Indicates the power reflected back from the antenna system to the transceiver.
    • SWR (Standing Wave Ratio): Indicates the impedance match between your transceiver and antenna. An SWR close to 1:1 is ideal.
Side view of the NISSEI RX-103 SWR/Watt Meter
Side view of the NISSEI RX-103 SWR/Watt Meter, showing its compact design.

Product demonstration video of the NISSEI RX-103 SWR/Watt Meter, showcasing its features and operation.

4. Maintenance

To ensure the longevity and accurate performance of your NISSEI RX-103 SWR/Watt Meter:

  • Keep the device dry and away from excessive moisture or humidity.
  • Clean the exterior with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
  • Avoid exposing the meter to extreme temperatures or direct sunlight for prolonged periods.
  • Store the meter in a safe place when not in use to prevent physical damage.

5. Troubleshooting

If you encounter issues with your NISSEI RX-103 SWR/Watt Meter, consider the following:

  • No Display/Power: Check the 13.8V DC power connection. Ensure the power source is active and providing the correct voltage.
  • Incorrect Readings: Verify all antenna and transceiver connections are secure and correctly seated in the SO-239 connectors. Ensure the selected 'RANGE' setting is appropriate for your transmit power.
  • High SWR Readings: High SWR typically indicates an issue with your antenna system (e.g., antenna length, tuning, or faulty cable). The meter accurately reflects the SWR of your system; it does not cause it.

6. Specifications

FeatureSpecification
ModelRX-103
Frequency Range1.6 - 60 MHz
Measurable Power Range0 - 2000 W
Measuring Gear20 / 200 / 2000 W
Max Measured Power2000 W
Measurement Accuracy (2W gear AVG)+/- 10%
Measurement Accuracy (2W gear PEP)+/- 15%
Measurement Accuracy (20/200W gear AVG)+/- 5%
Measurement Accuracy (20/200W gear PEP)+/- 10%
Minimum Measurement Power1 W
Connector TypeSO-239 M head
Net Weight780 g
Insertion LossLess than 0.1 dB
Measurable ParametersFWD / REV Power, PEP, SWR
Impedance50 Ohm
Dimensions (W/H/D)140 x 84 x 122 mm
DIY Supplies CategoryElectrical
CertificationCE

7. User Tips

  • Frequency Compatibility: Please note that the NISSEI RX-103 is designed for a frequency range of 1.6 - 60 MHz. It is not suitable for measuring signals in the commercial FM band (88-108 MHz).
  • Accurate Readings: For the most accurate power and SWR readings, ensure your antenna system is properly tuned and all connections are tight.

8. Warranty and Support

For any questions, technical support, or warranty inquiries regarding your NISSEI RX-103 SWR/Watt Meter, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.