jingsha B75M-I Motherboard Kit

Contents

Jingsha B75 Mini-ITX Motherboard Kit User Manual

Model: B75M-I Motherboard Kit

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Jingsha B75M-I Mini-ITX Motherboard Kit. This kit includes a B75M-I motherboard, an Intel Core i5 3470 processor, and 16GB (2x8GB) DDR3 1600MHz desktop RAM. Please read this manual carefully before proceeding with installation to ensure proper setup and prevent damage.

Jingsha B75M-I Motherboard Kit with Intel Core i5 3470 CPU and two 8GB DDR3 RAM modules
Figure 1: Jingsha B75M-I Motherboard Kit Components

2. Warning & Safety Information

  • Do not use the motherboard in humid environments.
  • Avoid areas with strong electromagnetic interference.
  • Always disconnect power before installation or maintenance.
  • When inserting or removing hardware, take extreme care not to damage motherboard pins or components.
  • Prevent electrostatic discharge (ESD) damage during installation by grounding yourself.
  • Do not force insertion or removal of hardware components.
  • Ensure adequate ventilation and heat dissipation for optimal performance and longevity.

3. Package Contents

The Jingsha B75M-I Motherboard Kit includes the following components:

  • 1x Jingsha B75M-I Mini-ITX Motherboard
  • 1x Intel Core i5 3470 Processor (pre-installed or separate)
  • 2x 8GB DDR3 1600MHz Desktop RAM Modules (16GB total)

Note: The CR2032 battery for the CMOS will be removed before shipment due to international shipping regulations. Please acquire and install a new CR2032 battery if needed.

Note about CR2032 battery removal from motherboard
Figure 2: CR2032 Battery Removal Notice

4. Specifications

Table 1: Jingsha B75M-I Motherboard Kit Specifications
Component Specification
Motherboard ModelB75M-I
ChipsetIntel B75
Socket TypeLGA 1155
ProcessorIntel Core i5 3470 (4 cores/4 threads, 3.2GHz, 6MB L3 Cache, 22nm, 77W TDP)
Memory TypeDDR3 (1.5V standard-voltage, non-ECC)
Memory Slots2 (Dual Channel)
Max RAM Capacity16 GB
Storage Interface4x SATA Ports (1x SATA3.0, 3x SATA2.0), 2x M.2 Slots (1x NVMe x4 2.0 or 1x M.2 2280 NGFF SATA2.0 Protocol SSD Port, 1x M.2 WIFI)
PCI-E StandardsPCI-E 3.0
PCIe x16 Slots1
PCI Slots1
Onboard LAN1x RJ45 (1000Mbps Ethernet, RTL8111F)
Audio Channels2.1 (CJC6811A)
Back I/O Ports1x HD, 1x VGA, 4x USB2.0, 2x USB3.0, 1x RJ45, 1x Audio (3.5mm jacks)
Onboard Connectors24-pin Main Power, CPU Fan, 3-pin SYS FAN, Front Audio, USB2.0, USB3.0, Speaker, CMOS header, Power On, COM header, Debug header, M.2 WIFI, 8-pin 12V connector
Form FactorMini-ITX (170mm x 170mm)
Quality CertificationCE
ApplicationDesktop (Audio & Video, Household, Office, Design, Video Production, others)
Product Specifications Table
Figure 3: Detailed Product Specifications
Back I/O Ports Diagram
Figure 4: Back I/O Ports Layout

5. Setup Instructions

Follow these steps to install the components and prepare your motherboard for use.

5.1. CPU Installation

  1. Open the CPU socket lever and pressure bar as shown in the diagram.
  2. Carefully place the Intel Core i5 3470 CPU into the LGA 1155 socket. Ensure the CPU's gold triangle aligns with the motherboard's golden corner. Do not force the CPU into the socket to avoid bending pins.
  3. Close the pressure bar and secure the lever to lock the CPU in place.
Step-by-step CPU installation method
Figure 5: CPU Installation Method

5.2. RAM Installation

  1. Locate the two DDR3 memory slots on the motherboard.
  2. Open the retention clips on both ends of the memory slot.
  3. Align the notch on the DDR3 RAM module with the key in the memory slot.
  4. Insert the RAM module firmly into the slot until the retention clips snap into place. Repeat for the second RAM module.
DDR3 RAM modules in green and black colors
Figure 6: DDR3 RAM Modules (Note: Color may vary)
Memory strip variations, narrow plate and wide plate
Figure 7: Memory Strip Variations (Narrow vs. Wide Plate)

5.3. M.2 SSD Installation

The motherboard supports NVMe M.2 SSDs. Ensure your M.2 SSD is NVMe compatible.

  1. Locate the M.2 slot(s) on the motherboard.
  2. Insert the M.2 SSD into the slot at an angle, ensuring the contacts are fully seated.
  3. Gently push down the other end of the SSD and secure it with the provided screw.
Diagram showing support for NVMe M.2 and non-support for SATA M.2
Figure 8: NVMe M.2 Support
Diagram illustrating correct M.2 SSD installation to prevent interface damage
Figure 9: Correct M.2 SSD Installation

5.4. Power Connections

Connect the 24-pin ATX main power connector and the 8-pin 12V CPU power connector from your power supply to the corresponding ports on the motherboard. Ensure all connections are secure.

Important: This platform requires a powerful power supply. Ensure your power supply is sufficient to support the system (at least 500W brand power supply is recommended).

B75M-I Motherboard Layout with labeled connectors
Figure 10: B75M-I Board Layout (Refer for connector locations)

5.5. Other Connections

Connect SATA drives, front panel headers (power, reset, USB, audio), and any other peripherals as needed. Refer to the motherboard layout diagram (Figure 10) for specific header locations.

6. Operating Instructions

After completing the hardware installation, connect your monitor, keyboard, and mouse. Power on your computer. The system should boot up, allowing you to install your operating system.

6.1. BIOS Access

To enter the BIOS/UEFI setup, press the designated key (usually DEL, F2, or F10) repeatedly during the initial boot sequence. Consult your monitor for the exact key prompt.

6.2. Video Demonstration

Video 1: Quick assembly guide for the motherboard, CPU, and RAM.

7. Maintenance

  • Keep the motherboard and components free from dust. Use compressed air for cleaning.
  • Ensure proper airflow within your PC case to prevent overheating.
  • The color of the bottom plate of the slot and memory strips (narrow/wide plate) may vary between production batches. This is normal and does not affect product functionality.
  • For warranty purposes, do not remove the warranty label on the back of the CPU.
CPU with a warranty label on the back
Figure 11: CPU with Warranty Label

8. Troubleshooting

8.1. Frequently Asked Questions (FAQ)

  • System fails to power on: Verify that all power connections (24-pin ATX, 8-pin CPU) are secure, and that the CPU and memory are properly installed.
  • Blue Screen of Death (BSOD): This can indicate hardware incompatibility or driver issues. Update the motherboard BIOS or verify hardware compatibility for all installed components.
  • Hard drive not recognized: Confirm that the SATA data and power cables are correctly connected to both the drive and the motherboard. Check BIOS settings to ensure the drive is detected.
  • Unable to enter BIOS: Ensure you are pressing the correct key (usually DEL, F2, or F10) repeatedly immediately after powering on the system.
  • HDMI not working: Check cable connections, ensure your monitor is set to the correct input, and verify that the integrated graphics or discrete GPU drivers are installed correctly.

9. User Tips

  • Many users report successful first-time boot-ups when all components are correctly installed. Double-check all connections before powering on.
  • While a printed manual for power supply cable locations is not included, the product page often features detailed motherboard connection diagrams (e.g., Figure 10) which are very helpful.
  • The CPU often comes pre-installed on the motherboard, but RAM modules are typically separate.

10. Warranty & Support

The CPU included in this kit comes with a 1-year warranty, provided it is in good condition and the warranty label on the back is intact.

For BIOS files, drivers, or further technical assistance, please contact customer service.

A detailed user manual in PDF format is available for download: Jingsha B75 Motherboard User Manual (PDF)

© 2023 Jingsha. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.