ANYCUBIC 3D Printer Resin User Manual

1. Product Overview

ANYCUBIC offers a range of high-quality UV-curable resins designed for LCD and DLP 3D printers. This manual covers the usage and handling of ABS-Like Pro 2, Water Wash, and ECO Plant resins, providing guidelines for optimal printing results and safe operation.

Key Features:

• Strong and Tough: Enhanced toughness and elongation at break for durable models.
• High Flowability: Low viscosity for faster curing and reduced delamination.
• Low Odor: Improved formula for a more comfortable printing environment.
• High Precision: Minimal shrinkage for accurate and detailed prints.
• Wide Compatibility: Works with most 365-405nm LCD/DLP 3D printers.

2. Specifications

The following table details the general parameters for ANYCUBIC resins. Note that specific properties may vary slightly between resin types (ABS-Like Pro 2, Water Wash, ECO Plant) and batches.

Physical Properties:

• Material: Photosensitive Resin
• Form: Liquid
• Compatibility: LCD 3D Printers (365-405nm wavelength)

3. Setup and Preparation

1. Shake Resin: Before each use, thoroughly shake the liquid resin bottle to ensure proper mixing of components.

2. Clean Resin Tank: Ensure the resin tank and the molding platform are clean and free of debris. The bottom of the resin tank should have clear light transmission.

3. Temperature: The suggested operating temperature for printing is 18-35°C. If the ambient temperature is low, preheat the resin to no more than 60°C before use to avoid affecting the printing effect.

4. Pigment Settling: If the resin pigment has settled, stir or shake the resin before use.

4. Operating Instructions

1. Add Resin: Unscrew the cap of the resin bottle and carefully pour the resin into the printer's resin tank, following your equipment's specific requirements and fill lines.

   

2. Select Print Parameters: Refer to the recommended printing parameters table below for your specific printer model. Adjust settings such as layer thickness, exposure time, and lift speeds as needed for your desired print quality.

   Recommended Printing Parameters

   Printer Model	Layer Thickness	Exposure Time	Light-Off Time	Bottom Exposure Time	Bottom Layers	Anti-Aliasing Level	Z Lift Distance	Z Lift Speed	Z Retract Speed
   Photon Mono M7	0.05mm	2.2s	1s	35s	4	1	8mm	6mm/s	6mm/s
   Photon Mono M7 Pro	0.05mm	2s	1s	25s	4	1	8mm	6mm/s	6mm/s
   Photon Mono M5s Pro	0.05mm	3.6s	1s	30s	5	1	8mm	6mm/s	6mm/s
   Photon Mono M5s	0.05mm	3s	0.5s	25s	5	1	8mm	6mm/s	6mm/s
   Photon Mono M5	0.05mm	2.8s	0.5s	25s	6	1	8mm	6mm/s	6mm/s
   Photon Mono X6Ks	0.05mm	2.5s	0.5s	20s	6	1	8mm	2mm/s	3mm/s
   Photon Mono 2	0.05mm	2.5s	1s	28s	5	1	6mm	4mm/s	6mm/s
   ANYCUBIC Photon M3 Max	0.05mm	3s	2s	30s	6	1	10mm	4mm/s	4mm/s
   Photon Mono X2	0.05mm	2.5s	0.5s	25s	5	1	8mm	3mm/s	3mm/s
   ANYCUBIC Photon M3 Premium	0.05mm	2.5s	0.5s	25s	3	1	8mm	6mm/s	6mm/s
   Photon Mono X 6K	0.05mm	2s	0.5s	23s	6	1	8mm	2mm/s	3mm/s
   Photon Mono 4K	0.05mm	2s	0.5s	40s	6	1	6mm	4mm/s	4mm/s

   

3. Start Printing: Initiate the printing process on your 3D printer according to its specific interface and instructions.

5. Post-Processing and Maintenance

5.1 Post-Processing Steps:

After printing, use appropriate tools for post-processing. This includes:

1. Remove Model: Carefully remove the printed model from the molding platform using a blade.
2. Clean Model: Submerge the model in a cleaning solution (e.g., alcohol for standard resins, water for Water Wash resins). Rinse or ultrasonically wash the model, then take it out and drain. ANYCUBIC Wash and Cure machines are highly recommended for better results.
3. Further Processing: Perform any necessary processing such as removing supports, polishing, or coloring.
4. Post-Curing: To ensure the mechanical properties of the model, perform post-curing immediately after cleaning and drying.

5.2 Post-Curing Guidelines:

Proper post-curing is essential for the final strength and durability of your prints. Control the intensity and time of the light source carefully.

• Mercury Lamp or LED Light Source: Intensity of 5-10mW/m², duration no more than 1 hour (self-regulation).
• Sunlight Exposure (Summer): Approximately 1 hour.
• Avoid Strong Light: Proximity or long-term exposure under strong light sources such as high-power high-pressure mercury lamps is prohibited.
• Printing Environment: It is recommended to print in a dark room or keep the printer covered with a lid, as resin is a photosensitive material.
• High Clear Resin: To prevent yellowing, reduce the exposure time by half compared to other resin colors.
• Black Resin: May appear partially transparent in thin walls (<0.5mm). Greater thickness can achieve better color effects.

5.3 Resin Storage:

• Store uncured resin in a cool, dark place at room temperature.
• Protect from direct light, high temperature, or sunlight.
• Ensure the bottle is tightly sealed to prevent contamination and premature curing.

6. Troubleshooting

• Print Failure/Delamination: Ensure the resin is thoroughly shaken before use. Verify that the resin tank and molding platform are clean. Check and adjust printing parameters (exposure time, lift speed) according to the recommended settings for your printer and resin type. Low ambient temperature can affect printing; preheat resin if necessary.
• Yellowing of Clear Resins: This can occur due to long-term curing. Reduce post-curing exposure time by half for High Clear Resins.
• Resin Pigment Settling: If pigment settles at the bottom of the bottle, shake the resin well before use.
• Models are Brittle: Ensure adequate post-curing is performed after cleaning and drying to achieve optimal mechanical properties.
• Poor Detail/Accuracy: Check for minimal shrinkage rates and ensure your printer is calibrated correctly.

7. Safety and Environmental Considerations

7.1 General Precautions:

• Always wear appropriate personal protective equipment (PPE), including gloves and safety glasses, when handling resin.
• Work in a well-ventilated area to minimize exposure to resin fumes.
• Avoid direct skin contact and eye contact with liquid resin. In case of contact, wash immediately with soap and water. If irritation persists, seek medical attention.
• Keep resin out of reach of children and pets.
• Refer to the Material Safety Data Sheet (MSDS) for comprehensive safety information.

7.2 Wastewater Post-Process:

Proper disposal of resin wastewater is crucial to protect the environment:

1. Do Not Discharge: Never discharge resin wastewater directly into sewers or drains to avoid contaminating groundwater.
2. Evaporation and Curing: Heat the wastewater to evaporate most of the water. The remaining residue should then be cured under UV light (e.g., curing machine or sunlight) until solid.
3. Solid Waste Disposal: Dispose of the solidified resin residue as general solid waste according to local regulations.

8. User Tips

• Low Odor Advantage: ANYCUBIC resins are formulated for low odor, making your printing experience more pleasant. However, always ensure good ventilation.
• Easy Cleaning: Water Wash resins simplify post-processing by allowing cleaning with water, reducing the need for harsh chemicals like IPA.
• Enhanced Durability: ABS-Like Pro 2 resins offer improved toughness and bending resistance, ideal for functional parts that require more resilience.
• Precision Printing: Leverage the minimal shrinkage of these resins to achieve highly accurate and detailed models.
• Color Consistency: The upgraded black ABS-Like Pro 2 resin provides enhanced color saturation and richness.

9. Warranty and Support

For specific warranty information regarding your ANYCUBIC resin product, please refer to the product packaging or contact ANYCUBIC customer support directly. The typical shelf life for these resins is 1.5 years when stored correctly.

If you encounter any problems or have questions while using the resin, please feel free to contact ANYCUBIC customer service for assistance.