1. Introduction
Thank you for choosing the TKLBLS K-4 4-Channel Audio Mixer. This professional mixer is designed for a wide range of audio applications, from live performances and DJ sets to home studio recording and live broadcasting. Featuring a USB audio interface, Bluetooth 5.0 connectivity, 99 built-in DSP effects, and a 3-band EQ, the K-4 offers versatile control over your audio. Please read this manual thoroughly to understand the mixer's functions and ensure safe and optimal operation.
2. Product Overview
The TKLBLS K-4 is a compact yet powerful 4-channel audio mixer. Below is a diagram illustrating its main controls and connection points.

Key Components:
- Microphone Input (MIC/LINE 1-2): XLR/TRS combo jacks for microphones or line-level instruments.
- HI-Z Switch: For high-impedance instruments like guitars.
- +48V Phantom Switch: Activates phantom power for condenser microphones.
- Gain Knob: Adjusts input sensitivity for each channel.
- EQ Knobs (HIGH, MID, LOW): 3-band equalizer for tone shaping.
- FX Knob: Adjusts the amount of effect sent to the channel.
- PEAK Indicator: Lights up when the input signal is too high.
- Volume Knob (LEVEL): Adjusts the output level of each channel.
- LINE UNBAL 3/4: Stereo line input for external devices.
- REC OUT: RCA outputs for recording.
- PHONES: Headphone output jack.
- USB Interface: For computer connection and U-disk playback.
- Display Screen: Shows DSP effect number and other status.
- DSP Program Knob: Selects one of the 99 DSP effects.
- PREV/NEXT/PIP/MODE Buttons: For navigating DSP effects and Bluetooth/USB modes.
- PWR/CLIP/SIG/OUT LEVEL Indicators: Power, clipping, signal, and output level indicators.
- STEREO Volume Knob: Main stereo output volume.
- PHONES Volume Knob: Headphone output volume.
- Power Switch: Turns the mixer on/off.
3. Features
- 4-Channel Input: Two MIC/LINE (XLR/TRS combo) inputs and one stereo LINE (unbalanced TRS) input.
- USB Audio Interface: Supports lossless data transmission for PC and mobile devices (via OTG cable, not included) for live broadcasting and recording.
- Bluetooth 5.0 Connectivity: Built-in module for fast, stable, and lossless wireless audio streaming.
- 99 DSP Effects: A 24-bit multi-FX processor with a wide range of effects including: Hall (00-09), Room (10-19), Delay (20-29), Ping Pong (30-39), Echo (40-49), Reverb (50-59), Karaoke (60-69), Pitch (70-79), Chorus (80-84), Tremolo (85-89), Flange (90-94), and Auto Tune (95-99).
- 3-Band Equalizer: High, Mid, and Low frequency controls on input channels for precise tone adjustment.
- 48V Phantom Power: Switchable phantom power for condenser microphones on MIC/LINE inputs 1 and 2.
- HI-Z Input: Dedicated high-impedance input for direct connection of guitars and other instruments.
- One-Key Low Cut: Filters out unwanted low-frequency rumble, especially useful for guitar equipment.
- Anti-Whistling Smart Chip: Intelligent audio processing and noise reduction technology for improved sound quality and output.
- No Delay Earphone Monitoring: Provides non-destructive sound feedback for real-time monitoring.
- Compact and Portable Design: Light and complete in function, suitable for various indoor and outdoor applications.
4. Setup Instructions
4.1 Power Connection
- Ensure the mixer's power switch is in the OFF position.
- Connect the included DC power adapter to the mixer's power input jack.
- Plug the power adapter into a suitable electrical outlet.
- Turn the mixer's power switch to the ON position. The PWR indicator should light up.
Important: Ensure you use the correct power adapter for your region. If the provided adapter is not compatible, you will need to source a suitable replacement.
4.2 Connecting Microphones and Instruments

- Microphones: Connect dynamic or condenser microphones to the MIC/LINE 1 or 2 XLR/TRS combo jacks. For condenser microphones requiring phantom power, activate the +48V switch for the respective channel.
- Instruments (High Impedance): Connect guitars or other high-impedance instruments to MIC/LINE 1 or 2 and engage the HI-Z switch for that channel.
- Line-Level Devices: Connect keyboards, electronic organs, or other line-level devices to the LINE UNBAL 3/4 inputs using TRS cables.
- USB Devices: Insert a USB flash drive into the USB interface for playback.
4.3 Connecting to a Computer/Mobile Device


- For PC: Connect the mixer to your computer using a USB cable. The mixer will function as an audio interface, allowing for lossless data transmission for recording or live streaming.
- For Mobile: Connect the mixer to your mobile phone using a suitable OTG (On-The-Go) cable (not included). This enables lossless audio transmission for mobile live broadcasting.
4.4 Connecting Output Devices
- Headphones: Plug your headphones into the PHONES jack for monitoring.
- Recording Devices: Connect your recording device to the REC OUT RCA jacks.
- Main Output: Connect your power amplifier or active speakers to the main output (L/R) jacks.
5. Operating Instructions
5.1 Basic Audio Mixing
- Gain Adjustment: For each input channel, slowly turn the GAIN knob clockwise until the PEAK indicator flashes only occasionally during the loudest parts of the signal. Avoid constant illumination of the PEAK light to prevent distortion.
- Equalization (EQ): Use the HIGH, MID, and LOW knobs to adjust the tone of each channel. Turn clockwise to boost frequencies, counter-clockwise to cut them.
- Channel Volume: Adjust the LEVEL knob for each channel to set its individual volume in the mix.
- Main Output Volume: Use the STEREO volume knob to control the overall output level of the main mix.
- Headphone Volume: Adjust the PHONES volume knob for comfortable monitoring levels.
5.2 DSP Effects

- Selecting Effects: Turn the PROGRAM knob to cycle through the 99 built-in DSP effects. The selected effect number will be shown on the display screen.
- Applying Effects: Use the FX knob on each channel to send a portion of that channel's signal to the selected DSP effect.
- Effect List: The mixer includes various effects such as Hall, Room, Delay, Echo, Reverb, Karaoke, Pitch, Chorus, Tremolo, Flange, and Auto Tune.
5.3 Bluetooth Operation

- Press the MODE button until 'BLUE' appears on the display.
- On your Bluetooth-enabled device, search for available devices and select 'TKLBLS K-4'.
- Once paired, you can stream audio wirelessly to the mixer.
5.4 USB Playback
- Insert a USB flash drive containing audio files into the USB interface.
- Press the MODE button to switch to USB playback mode.
- Use the PREV/NEXT buttons to navigate tracks.
5.5 Low Cut Function

Press the 'LOW CUT' button on the desired channel to activate the low-frequency filter. This is particularly useful for instruments like guitars to remove unwanted bass rumble.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the mixer's surface. Do not use liquid cleaners or solvents.
- Storage: Store the mixer in a cool, dry place away from direct sunlight and extreme temperatures.
- Cable Management: Ensure all cables are neatly organized and not under strain to prevent damage to connectors and ports.
- Dust Protection: When not in use, cover the mixer to protect it from dust and debris.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound output |
|
|
| Distorted sound |
|
|
| Microphone not working (condenser mic) | 48V Phantom Power not activated. | Engage the +48V switch for the connected microphone channel. |
| Bluetooth connection issues |
|
|
| Humming or buzzing noise | Ground loop or interference. | Ensure all equipment is properly grounded. Try connecting devices to the same power strip. Check for faulty cables. |
8. Specifications

| Parameter | Value |
|---|---|
| Channel MIC/LINE | 4-channel |
| Total Harmonic Distortion | ≤0.05% |
| Frequency Response | 20Hz~18KHz |
| Max Outputs | 4V Max |
| S/N Ratio | ≥90dB |
| Input Sensitivity (Mic) | -50dB |
| Input Sensitivity (Line) | -40dB |
| Input EQ (HI) | ±15dB/12KHz |
| Input EQ (LOW) | ±15dB/80Hz |
| Phantom Power | +48V |
| Dimensions (W x D x H) | 165mm x 180mm x 38mm |
| Weight | 0.804 kg |
| Power Source | DC |
| Built-in Battery | No |
9. User Tips
- Auto Tune DSP: The 'Auto Tune' DSP effect (programs 95-99) is designed for vocal pitch correction and enhancement, providing a modern vocal sound.
- Power Adapter: Always verify that the power adapter supplied is compatible with your region's electrical standards (e.g., 220V for Europe). If not, acquire a suitable and certified adapter to prevent damage to the device.
- Mobile Connectivity: For connecting to mobile devices, ensure you have a compatible OTG (On-The-Go) cable for lossless audio transmission.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.