1. Product Introduction
The RETEKESS TH107 is a smart medical call system designed for convenient and practical use in various environments such as hospitals, clinics, nursing homes, and communities. It features a 32-channel number display, multi-language support, adjustable volume, and three-color light alarms to intuitively distinguish call urgency.
1.1 Screen Host (Receiver) Diagram (Applicable to TH107/TH108 model)
Figure 1: Front view of the TH107 screen host with numbered call buttons. The screen displays numbers 1-32.
Figure 2: Rear view of the TH107 screen host showing ports and battery compartment.
- Power DC jack
- TYPE-C interface
- 3.5mm-Audio interface
- Antenna
- Secondary screen
- Main screen
- Confirm key
- Level key
- PgUp (Page Up)
- PgDn (Page Down)
- C/Back key (Cancel/Back)
- AC key
- Hanging hole location
- Battery cover
- Power key
1.2 Extension (Call Button) Diagram
Figure 3: One-key call button with 'Call' button.
Figure 4: Two-key call button with 'Call' and 'Clear' buttons.
- LED indicator light
- Cancel key (for two-button models)
- Call button
- Base
LoRa extensions (TH010 model) are also available, featuring a single 'SOS' call button and magnetic charging.
Figure 5: LoRa extension call button with magnetic charging cable.
2. Specifications
2.1 Screen Host (Receiver) Specifications
- Size: 26.5 x 15.5 x 3.3 cm
- Material: ABS
- Screen: Main screen - LED matrix display; Secondary screen - three digital tube
- Modulation: 433.92MHz-AM (OOK) (for TH107 model); 427.975MHz-LoRa (for TH108 model)
- Extension Capacity: Each channel accommodates 8 extensions, for a total of 32 channels and 256 extensions
- Power: 12V-1A input; or 4 AA batteries
- FCC ID: 2A3NOTH010
2.2 Dual Button/Single Button Extension Specifications (TH008/TH009 model)
- Size: Extension 6.75cm (diameter) * 1.45cm; Base 7.25cm (diameter) * 1.95cm
- Material: ABS
- Modulation: 433.92MHz/AM (OOK)
- Battery: 23V12 battery * 1pcs (built-in)
- Communication Distance: Maximum 800m (open area)
- Power: 10mW
- Battery Life: 6000-7000 times (button presses)
2.3 LoRa Extension Specifications (TH010 model)
- Size: 47 x 63 x 20 mm
- Material: ABS
- Power: 10mW
- Built-in Battery: 400mAh lithium battery
- Working Current: 130mA (Full battery can call about 6000 times)
- Charging Interface: Contact magnetic charging 5V1A
- Communication Distance: Up to 2000m (open area)
- Modulation: LoRA, 427.975MHz
2.4 Combined Specifications Overview
Figure 6: Detailed specifications for the receiving host and call buttons.
3. Setup Instructions
3.1 Unboxing and Initial Preparation
Before using the product, ensure all components are present and undamaged. The extension units (call buttons) are equipped with batteries from the factory. After unpacking, pair the extension with the screen host for normal operation.
- Single-button/dual-button extensions come with a base, wall-mount screws, and adhesive backing.
- LoRa extensions come with a hanging rope and a magnetic charging cable with pin connectors.
- The main screen comes with wall-mount screws for convenient installation.
Figure 7: Call button mounting options: paste on the wall or screw to the wall.
3.2 Power Supply Methods
The screen host supports multiple power supply options:
- DC Power Supply: Connect the provided power adapter to the DC 12V jack.
- Type-C Power Supply: Use a Type-C cable to power the device.
- Battery Power Supply: Insert 4 AA batteries into the battery compartment.
Figure 8: The screen host can be powered by batteries, Type-C, or DC 12V.
Note on Battery Power: A new battery can support normal operation for approximately 8 hours and standby for around 30 hours. When the battery level is low, the battery icon will continuously flash to prompt replacement. The host does not have the ability to charge batteries.
3.3 Adding and Pairing Call Buttons (Grouping Management F2)
To add an extension (call button) to a group:
- Toggle the keys on the back of the screen host to the setting position to open the setup function.
- Short press the [Confirm] key to enter the setup state. The main screen will go out, the sub-screen will display "F1", and the host will broadcast "language settings".
- Short press [PgUp] / [PgDn] keys until the sub-screen displays "F2", and the host voice broadcasts "group management".
- Short press the [Confirm] key again to enter the group management setting state. The main screen will default to group 1 flashing white, and the sub-screen will display "--".
- Use [PgUp] / [PgDn] keys to select the desired group number on the main screen. The selected group number will blink white.
- Add Extension:
- Short press the extension button (call button). The host will broadcast the group number, the main screen group number will flash green, and the sub-screen will display the extension number (1-8) within that group. The host will prompt with a "drop" sound.
- At this point, you can set the level of extensions by short pressing the [Level] key. The main screen will show the corresponding group number lamps blinking in the current level's color.
- Short press the [Confirm] key, or wait for 3 seconds. The sub-screen will display "---", and the host will beep "drop", indicating the extension has been added.
- You can add up to 8 extensions per group. If more than 8 are added, the host will beep and the sub-screen will display "Er".
- To add extensions to other groups, use the [PgUp] / [PgDn] keys to select a different group.
- After all extensions are added, short press the [C/Back] key to return to the previous menu. The main screen will go out, and the sub-screen will display "F2".
- Short press [C/Back] again to exit the setup state. The host will beep "drop" and return to the receiving state.
Video 1: Demonstration of adding a call button and making a call.
4. Operating Instructions
4.1 Making a Call from an Extension
- For single-key/dual-key extensions: Press the Call button.
- For LoRa extensions: Press the red Call button (SOS button).
Upon receiving a call, the extension number will be displayed on both the main and secondary screens of the host. The main screen will flash to indicate the call, and the secondary screen will show the most recent call's number.
4.2 Canceling a Call
- For two-button extensions: Press the Clear button on the extension.
- For single-button and LoRa extensions: Calls can only be canceled on the host unit.
4.3 Language Setting (F1)
The screen host supports 10 languages. To change the language:
- Toggle the keys on the back of the screen host to the setting position.
- Short press the [Confirm] key. The main screen will go out, the sub-screen will display "F1", and the host will broadcast "language setting".
- Use [PgUp] / [PgDn] keys to cycle through the available languages. The host will broadcast "Hello" in the currently selected language, and the secondary screen will display numbers (1-10) corresponding to the language.
- Short press the [C/Back] key to confirm the selection and return to the previous menu. The host will beep "drop", and the sub-screen will display "F1".
- To exit the setup state, short press [C/Back] again.
Video 2: Demonstration of language setting on the screen host.
4.4 Volume Adjustment
To adjust the volume when there is no call information or record:
- Toggle the keys on the back of the screen host to the setting position.
- Short press [PgUp] / [PgDn] keys to adjust the volume. The main screen will go out, and the secondary screen will display the volume level (0-5).
- The host will broadcast a prompt tone at the currently selected volume.
- After selection, it automatically returns to the receiving state.
Video 3: Demonstration of volume adjustment on the screen host.
4.5 Call Record Management
The system supports displaying and managing call records. The main screen displays all call records, with the nearest calling group number flashing in the color of the extension level.
- Deleting a Single Call Record:
- Short press [PgUp] / [PgDn] to select the group number. The selected group number on the main screen will flash, and other group numbers will remain lit. The sub-screen will flash the nearest calling extension number, and the host voice will broadcast the group number.
- Short press the [AC] key to delete the group record. The main screen group number will turn off, and the host voice will prompt "drop", indicating successful deletion.
- Alternatively, short press [Confirm], then use [PgUp] / [PgDn] to select the specific extension number within the group. The sub-screen will flash the extension number. Short press the [Clear] key, and the host will prompt "drop", indicating successful deletion of that extension's call record.
- Deleting All Call Records: Short press the [AC] key briefly to clear all call records. The host will beep "drop" and return to standby.
Video 4: Demonstration of deleting call records on the screen host.
4.6 Alarm Lights and Prompt Tones
The TH107 screen host uses a three-color light alarm system to indicate call urgency:
- Green: Ordinary call
- Red: Emergency call
- Blue: Timeout call
Figure 9: Three-color light alarm for different call types.
The system also supports 3 prompt tones and 10 languages for voice broadcasts.
Video 5: Demonstration of the 3-color light alarm and switching between alarm types.
4.7 Timeout Time Setting (F4)
This feature reminds users of unprocessed calls after a set timeout. The host will voice remind twice, the main screen group number will flash blue, and the sub-screen will flash the extension group number.
- Toggle the keys on the back of the screen host to the setting position.
- Short press [Confirm]. The main screen will go out, the sub-screen will display "F1", and the host will broadcast "language settings".
- Short press [PgUp] / [PgDn] until the sub-screen displays "F4", and the host voice broadcasts "timeout settings".
- Short press [Confirm]. Use [PgUp] / [PgDn] to select the timeout duration (0-99 minutes). 0 means no timeout reminder is set.
- Short press [C/Back] to confirm and return to the previous menu.
4.8 Setting the Number of Beeps (F5)
This setting controls how many times the host beeps for a call.
- Toggle the keys on the back of the screen host to the setting position.
- Short press [Confirm]. The main screen will go out, the sub-screen will display "F1", and the host will broadcast "language settings".
- Short press [PgUp] / [PgDn] until the sub-screen displays "F5", and the host voice broadcasts "beep broadcasting number of times to set".
- Short press [PgUp] / [PgDn] to select the number of reminders (0-5). 0 means the reminder is always prompted.
- Short press [C/Back] to confirm and return to the previous menu.
4.9 Extension Level Setting
This allows setting priority levels for extensions.
- Short press the [Level] key to enter level setting. The default group number 1 on the main screen will flash white, and the sub-screen will show "---".
- Short press an extension button. The main screen group number will flash with the current extension's color, and the sub-screen will display the extension number within the group.
- Short press the [Level] key to cycle through extension levels. The main screen group number will flash in the color of the current level, and the sub-screen will show the extension in the group number.
- Short press the [Confirm] key, or wait for 3 seconds, to complete the setting. The main screen group number will turn white, the sub-screen will display "---", and the host will beep "drop".
5. Maintenance
5.1 Cleaning
- Dirty battery contacts should be wiped with a clean, dry cloth, both on the battery and in the appliance.
- For general cleaning, use a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
5.2 Battery Care and Replacement
- If the battery icon on the secondary screen continuously flashes, replace the batteries promptly.
- Turn off the radio before removing or installing batteries. Store spare batteries securely.
- Dispose of used batteries immediately and safely according to local regulations.
- If a radio or battery has been submerged in water, dry and clean it before use. Do not use appliances or heat sources like hair dryers or microwaves. If submerged in corrosive substances (e.g., saltwater), rinse with fresh water then dry.
- Batteries should be removed from the appliance when not in use for long periods (months).
- Do not dismantle, open, or shred batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd; Ni-MH) batteries.
- Do not mix different types of batteries or new and used batteries.
- Batteries must be inserted with the correct polarity.
5.3 Waterproof Rating
The nurse call buttons are IP67 waterproof, designed to prevent accidental water contact during use.
Figure 10: The call button is IP67 waterproof.
Note: The screen host does not have waterproof function and should not be placed in high temperature, humid, or dusty environments for extended periods.
6. Troubleshooting
- Device not responding: Ensure the device is properly powered. Check battery levels or DC/Type-C connections.
- Interference: Nearly all electronic devices are susceptible to electromagnetic interference (EMI). If interference occurs, turn off the radio in areas where signs are posted, such as hospitals or healthcare facilities.
- Call button not pairing: Ensure you follow the grouping management instructions carefully. If issues persist, try restoring factory settings and re-pairing.
- No sound/low volume: Adjust the volume settings as described in section 4.4.
- Data loss or product damage: Always follow the instructions in this manual. Failure to do so may result in data loss or damage.
6.1 Restore Factory Settings (F6)
To restore the screen host to its factory default settings:
- Toggle the keys on the back of the screen host to the setting position.
- Short press [Confirm]. The main screen will go out, the sub-screen will display "F1", and the host will broadcast "language settings".
- Short press [PgDn] until the sub-screen displays "F6", and the host voice broadcasts "restore factory settings".
- Short press [Confirm]. Use [PgUp] / [PgDn] to set the value from 1 to 0 (default is 1).
- After setting, long press [Confirm] + [C/Back]. The host will beep "drop", indicating the setting is complete, and return to the receiving state.
7. Safety Information
7.1 RF Energy Exposure and Product Safety Guide
This device uses electromagnetic energy in the radio frequency (RF) spectrum. Improper use can cause biological damage. Please refer to official guidelines for RF exposure limits. It is important to maintain a proper distance from the radio, as RF exposure decreases with increasing distance from the antenna. Use only manufacturer-supplied or authorized antennas and accessories to ensure compliance with RF exposure limits.
To reduce RF exposure:
- Reduce the amount of time spent using your wireless device.
- Use a speakerphone, earpiece, headset, or other hands-free accessory to reduce proximity to the head.
- Increase the distance between wireless devices and your body.
- Transmit no more than 50% of the time.
7.2 Electromagnetic Interference/Compatibility
Almost all electronic devices are susceptible to electromagnetic interference (EMI). Your radio generates RF energy that can cause interference with other devices. To avoid interference, turn off the radio in areas where signs indicate, such as hospitals or healthcare facilities.
Turn off your radio in the following conditions:
- Do not use any radio that has a damaged antenna.
- Turn off your radio before removing or installing accessories.
- When the transceiver is used for long transmissions, the radiator and chassis will become hot.
7.3 Protect Your Hearing
- Use the lowest volume necessary.
- Limit the duration of using headsets or earphones at high volume.
- Do not place the radio's speaker directly against your ear.
- Excessive sound pressure from earphones and headphones can cause hearing loss.
CAUTION: Exposure to loud noises for prolonged periods can temporarily or permanently affect your hearing.
7.4 Choking Hazard
WARNING: CHOKING HAZARD - Small Parts. Not suitable for children under 3 years old.
8. User Tips
- When managing multiple calls, the system displays calls in the order they are received, which can be helpful for prioritizing responses.
- Utilize the three-color light alarm (Green for ordinary, Red for emergency, Blue for timeout) to quickly assess the urgency of incoming calls without needing to listen to voice prompts.
- For optimal range, ensure the screen host's antenna is fully extended and positioned in an open area.
- Regularly check the battery icon on the screen host and replace batteries promptly when flashing to ensure uninterrupted service.
9. Warranty and Support
Most new products carry a two-year manufacturer's warranty from the date of purchase.
For warranty service, you will need to provide a receipt or proof of purchase from the seller for verification.
Exclusions from Warranty Coverage:
- Product damaged by accident.
- Misuse or abuse of the product, or unauthorized alterations or repairs.
- Altered, defaced, or removed serial number.
For assistance regarding repairs and service, or for a list of approved accessories for your radio model, visit the official RETEKESS website: www.retekess.com.
An official user manual (PDF) is also available for download, which may contain additional detailed instructions. You can find it by searching for 'Item guides & documents' on the product page or directly via the provided PDF link: User manual (PDF).
10. Regulatory Compliance
10.1 FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
10.2 IC (Innovation, Science and Economic Development Canada) Compliance
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
10.3 CE (European Conformity) Declaration
HENAN ESHOW ELECTRONIC COMMERCE CO., LTD. declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU, ROHS Directive 2011/65/EU, and WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available at www.retekess.com.
10.4 Disposal Information
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that all electrical and electronic products, batteries, or accumulators must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws and rules in your area.