1. Product Overview
This manual provides detailed instructions for the installation, operation, and maintenance of your KCQ Max 48V 500W Scooter Controller. This controller is specifically designed for 10-inch electric scooters.
Important Note: This controller only supports 10-inch scooters.

Figure 1: Complete KCQ Max Scooter Controller Kit Components. Includes the main controller unit, display, throttle, headlight, taillight, and various wiring harnesses.
2. Specifications
| Parameter | Value |
|---|---|
| Voltage | DC48V |
| Rated Power | 500W |
| Undervoltage Protection | 41V ± 1V |
| Current Limit | 18A ± 1A |
| Braking Method | Linear brake |
| Start Method | Dual Mode |
| Adaptation Motor | 10-inch motor |
| Max Speed | 20/35/48 km/h |
| Authentication | CE |

Figure 2: Close-up of the controller label showing detailed technical specifications.

Figure 3: CE Certificate of Conformity, indicating compliance with European safety standards.
3. Setup and Installation
Carefully follow these instructions for proper installation. Incorrect wiring can damage the controller or scooter.
3.1 Component Identification
Familiarize yourself with the main components and their connections:

Figure 4: Detailed wiring diagram of the controller, showing connections for Motor Phase Line, Hall Line, Communication Line, Taillight Line, Burning Line, and XT60 Battery Connector.
- Motor Phase Line: Connects to the scooter motor.
- Hall Line: Connects to the motor's Hall sensors.
- Communication Line: Connects to the display unit.
- Taillight Line: Connects to the scooter's taillight.
- Burning Line: Specific function, ensure correct connection as per scooter's wiring.
- XT60 Battery Connector: Connects to the scooter's battery.

Figure 5: Close-up view of the XT60 power connector for battery connection.
3.2 Wiring Procedure
- Ensure the scooter's power is OFF and the battery is disconnected before starting any wiring.
- Connect the XT60 Battery Connector from the controller to your scooter's battery.
- Connect the Motor Phase Lines (usually three thicker wires) from the controller to the corresponding wires on your scooter's motor.
- Connect the Hall Line from the controller to the Hall sensor wires on your motor.
- Connect the Communication Line to the display unit.
- Connect the Taillight Line to the scooter's taillight.
- Connect the Burning Line as per your scooter's specific wiring requirements.
- Once all connections are secure, you can proceed to connect the display and throttle.

Figure 6: The scooter's display unit, which connects to the controller via the communication line.
3.3 APP Connection
The controller supports APP connectivity for enhanced control and settings. Scan the QR code provided with the product or refer to the product packaging for the official APP download link (Android/iOS compatible).

Figure 7: The main product image, which includes a QR code for downloading the KCQ Scooter APP.
4. Operating Instructions
4.1 Basic Operations
- Boot: Long press the power button (approximately 1 second). The buzzer will sound twice.
- Shutdown: Press and hold the power button for 3 seconds. The buzzer will sound twice.
- Lights: In the power-on state, short press the light button once (within 1 second) to turn on the front and rear lights. The headlights will be constantly on, and the taillights will flash.
- Brake: The system uses electronic brakes combined with disc brakes. When braking, the taillight will illuminate continuously.
- Gear Shift: In the power-on state, the default is low-speed gear. Press the gear shift button twice (within one second) to switch between gear positions. Green indicates low gear; red indicates high gear.
4.2 Advanced Features
- Low Voltage Alarm Speed Mode: When the battery voltage drops to 37V, the scooter will enter a low voltage alarm mode, limiting the speed to approximately 15 Km/h. To release this mode and return to normal operation, the throttle must be returned to its initial (zero) position, and the battery should be charged.
- Constant Speed Cruise: If the speed remains stable for approximately 6 seconds, the cruise control will automatically activate. Once cruise control is fixed, you can release the throttle. To disengage cruise control, press the brake or push the throttle again.
- Automatic Shutdown: The scooter will automatically shut down after 10 minutes of no operation to conserve battery life.
4.3 APP Functions
The dedicated APP allows for various settings and real-time monitoring:

Figure 8: Scooter APP interface displaying speed control, gear selection (1st, 2nd, 3rd), lock/unlock functions, and power on/off. The app adapts to your mobile phone's system language (English and French shown).
- Speed Control: Adjust speed settings and monitor current speed.
- Start Mode: Configure between 'Zero start' (no initial speed needed) and 'Non-zero start' (requires an initial push to start). This setting is crucial for user preference and safety.

Figure 9: APP setting screen illustrating the 'Zero start' and 'Non-zero start' options. 'Zero start' means no initial speed is required to begin riding.
- Lock/Unlock: Secure your scooter via the app.
- Power On/Off: Control the scooter's power state remotely.
- Unit Setting: Switch between mph and km/h.
- Tail Light Control: Toggle tail light on/off.
- Fixed Speed Cruise: Enable or disable cruise control.
- Connection Password: Set a password for secure APP connection.
5. Maintenance
To ensure the longevity and optimal performance of your scooter controller, follow these maintenance guidelines:
- Regular Inspection: Periodically check all wiring connections for looseness or damage. Ensure all connectors are securely seated.
- Cleanliness: Keep the controller unit clean and free from dust, dirt, and moisture. Use a dry, soft cloth for cleaning.
- Avoid Water Exposure: The controller is not waterproof. Avoid exposing it to water or excessive humidity. Water damage is not covered under warranty.
- Wire Integrity: Inspect all wires for cuts, fraying, or signs of wear. Damaged wires can lead to malfunctions or safety hazards. Wire damage is not covered under warranty.
- Battery Health: Ensure your scooter's battery is maintained according to its manufacturer's instructions. A healthy battery is crucial for the controller's proper function.
6. Troubleshooting
The display unit may show error codes if a problem occurs. Refer to the table below for common error codes and their solutions:
| Error Code | Description | Possible Causes | Solution |
|---|---|---|---|
| E0 | Temperature Protection | Motor reached set temperature limit. | Allow motor to cool down below the set value for normal operation. |
| E1 | Motor Hall Failure | Motor Hall sensor is damaged. | Replace the motor. |
| E2 | MOS Tube Failure | 1. Motor phase wires short-circuited. 2. Internal controller components damaged. | 1. Check motor phase wires for damage; replace motor if necessary. 2. Replace the controller. |
| E3 | Brake Failure | 1. Brake lever damaged. 2. Brake lever not returned to initial position before starting. | 1. Replace the brake lever. 2. Release the brake lever. If error persists, replace the brake lever. |
| E4 | Accelerator Failure | 1. Speed control handle damaged. 2. Speed control handle not returned to initial position before starting. | 1. Replace the speed control handle. 2. Loosen the speed control handle. If error persists, replace the speed control handle. |
| E5 | Undervoltage Protection | Supply voltage is below the controller's minimum operating voltage. | Charge or replace the battery. |
| E6 | Controller/Instrument Communication Failure | Instrument and controller cannot communicate. | 1. Check communication line connection. 2. Check motor phase line or Hall line for damage/leakage. 3. Replace the motor. |
| E7 | Overvoltage Protection | Supply voltage is above the controller's maximum operating voltage. | Replace battery or motor phase wire that matches the controller's voltage. Check for short circuits with Hall wire leading to leakage. |
| E8 | Controller Operational Amplifier Failure | Controller damaged due to water ingress or internal component failure. | Replace the controller. |
| E9 | Stalled Rotor Fault | 1. Obstacle preventing motor rotation. 2. Incorrect wiring sequence between motor and controller. | 1. Remove obstacle and loosen speed control handle. 2. Contact manufacturer for motor/controller matching. |
7. User Tips
- Wiring Check: Some users have found that adjusting the position of the engine control lines (green, blue, yellow, black, red) can resolve issues. Always ensure correct and secure connections.
- Kick Start Function: If your scooter has a 'kick start' function (requiring an initial push to engage the motor) and you wish to disable it, check the APP settings for a 'Start mode' option. You may be able to switch from 'Non-zero start' to 'Zero start' to allow immediate throttle response without an initial push.
- Compatibility: This controller is designed for 10-inch scooters. Ensure your scooter's motor and other components are compatible with a 48V 500W system.
8. Warranty and Support
8.1 Warranty Information
The manufacturer provides a warranty for this product. Please note that the warranty does not cover water damage or wire damage. It is crucial to protect the controller from moisture and ensure all wiring is handled carefully during installation and maintenance.
8.2 Technical Support
For further technical assistance, specific wiring questions not covered in this manual, or warranty claims, please contact the seller or manufacturer directly. Provide your product model number and a detailed description of the issue for efficient support.