1. Important Notes
This remote control is designed as a replacement for specific adjustable bed bases. Please review the following critical information before use:
Image: Important notes on remote compatibility, pairing, and model identification.
- Control Box Compatibility: The remote control is primarily compatible with control box model MC120. If your adjustable bed uses a different control box, please verify compatibility before attempting to pair.
- Remote Type: Dip switches are not compatible with Pair button models. Ensure your old remote control uses a Pair button system, not dip switches.
- Model Specificity: Many remote controls may look similar but are not universally compatible. This replacement remote is specifically designed for the brands and models listed.
- Pairing Requirement: The remote control requires pairing with your adjustable bed base before it can be used. The pairing method can vary between different bed models.
- Model Identification: If you are unsure about compatibility or your bed's model number is not explicitly listed, it is recommended to provide the exact model number and clear photos of the front and back of your old remote control for verification.
2. Setup and Pairing
2.1 Battery Installation
- Locate the battery compartment on the back of the remote control.
- Slide open the battery cover.
- Insert two AAA batteries (not included), ensuring correct polarity (+/-).
- Close the battery cover securely.
Image: Battery compartment for two AAA batteries.
2.2 Pairing Instructions
The pairing method for this remote control is as follows. Refer to your adjustable bed's original manual for specific instructions if these do not work, as pairing methods can vary by model.
- On the remote control, simultaneously press and hold the "Head Up" and "Foot Down" buttons for approximately ten seconds.
- Locate the "Reset Coding" button (sometimes labeled "Learn") on the control box of your adjustable bed base.
- Press and hold the "Reset Coding" button on the control box until you hear an audible tone. This tone indicates successful pairing.
Note: If your control box is not MC120, or if your old remote used dip switches, this pairing method may not be applicable.
3. Operating the Remote Control
The remote control features an intuitive button layout for controlling your adjustable bed base. The exact functionality of each button may depend on your bed's features.
Image: Front view of the remote control with button layout.
3.1 Button Functions
| Button | Function |
|---|---|
| Head Up / Head Down | Adjusts the head section of the bed upwards or downwards. |
| Foot Up / Foot Down | Adjusts the foot section of the bed upwards or downwards. |
| FLAT | Returns the bed to a completely flat position. |
| ZG (Zero Gravity) | Activates the Zero Gravity preset position. |
| M1 / M2 | Activates user-programmable memory positions 1 and 2. (Refer to your bed base manual for programming instructions). |
Point the remote control towards the bed base when operating. Ensure there are no obstructions between the remote and the bed base's receiver.
4. Maintenance
- Battery Replacement: Replace batteries when the remote's performance degrades or it stops responding. Always use two new AAA batteries.
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
- Storage: Store the remote in a dry place, away from direct sunlight and extreme temperatures.
5. Troubleshooting
- Remote Not Responding:
- Check if the batteries are correctly inserted and have sufficient charge. Replace if necessary.
- Ensure the remote is pointed directly at the bed base's receiver and there are no obstructions.
- Attempt the pairing process again (refer to Section 2.2).
- Bed Base Not Pairing:
- Confirm that your bed base uses a "Pair button" system and not "Dip switches."
- Verify that your control box is compatible (ideally MC120).
- Consult your original adjustable bed base manual for alternative pairing methods specific to your model.
- Incorrect Functionality:
- While this is a replacement remote, button layouts may slightly differ from your original. Ensure you are pressing the correct button for the desired function.
- If functions are completely incorrect, re-attempt pairing. If the issue persists, the remote may not be fully compatible with your specific bed base model.
6. Specifications
| Feature | Detail |
|---|---|
| Model Number | JLDK.105.09.11 |
| Wireless Communication | IR (Infrared) |
| Frequency | 433 MHz |
| Channel | 1 |
| Battery Type | 2 x AAA (not included) |
| Color | Black |
| Support APP | No |
| Use | Universal (for specified models) |
7. Warranty and Support
This product comes with a 3-month warranty from the date of purchase. Additionally, a 90+ day money-back return policy may apply. Please retain your proof of purchase for warranty claims.
For support or to confirm suitability if your model number is not explicitly listed, please contact the seller with the exact model of your device and clear photos of your old remote control (front and back).
8. User Tips
- Always check the model number of your adjustable bed base and old remote control to ensure maximum compatibility with this replacement unit.
- If the remote looks identical to your old one but doesn't work after pairing, double-check the pairing steps and ensure your bed base's control box is the MC120 model or a compatible alternative.
- Keep a spare set of AAA batteries on hand to avoid interruptions in use.
- For programmable memory positions (M1, M2), refer to your adjustable bed base's original manual for instructions on how to set and save your preferred positions.
