1. Introduction
Thank you for choosing Infitary LED Car Headlights. This manual provides detailed instructions for the installation, operation, and maintenance of your new LED headlights. Please read this manual thoroughly before installation and use to ensure proper function and safety.
1.1 Product Features
- High Brightness: Utilizes imported LED chips, providing several times higher brightness than traditional halogen lamps.
- Energy Saving & Environmental Protection: Significantly lower power consumption and a lifespan several times longer than traditional halogen lamps.
- Plug and Play: Compatible with the original vehicle circuit, requiring no circuit modifications (some models may require a decoder).
- Integrated Design: Features a built-in driver for intelligent temperature control and decoding.
- Efficient Heat Dissipation: Constructed with Aviation Aluminum 6063 and a quiet cooling fan for rapid heat dissipation and longer life.
- All-Weather Performance: Designed to provide good performance in various weather conditions including rain, fog, night, and snow.
- Durable Construction: IP68 waterproof rating ensures resilience against water ingress.
- Optimal Beam Angle: Features four luminous faces (for dual beam) or two luminous faces (for single beam) for a 360° beam angle, eliminating blind zones.
- Long Lifespan: Engineered for an operating life of over 50,000 hours, reducing the need for frequent replacements.


2. Specifications
| Attribute | Value |
|---|---|
| Brand Name | Infitary |
| Wattage | 72W/Pair |
| Voltage | 12V |
| Lumen | 8000LM |
| Color Temperature | 6500K |
| Waterproof Rating | IP68 |
| Light Source | COB |
| Beam Angle | 360 Degree |
| Material | Aviation Aluminum 6063 |
| Operating Life | Above 50,000 Hours |
| Operating Temperature | -60℃~+160℃ |
| Heat Dissipation Theory | Aviation Aluminum 6063 + Cooling Fan |
| Certification | CE, RoHS, FCC, WEEE |
| Car Compatibility | Most of the car (check socket type) |
| Package Contents | 2x LED Headlight Bulbs, 1x Installation Manual |

Explanation about Lamp Beads:
- Single Lamps (e.g., H7, H11, H1, H3, 880, 9005/HB3, 9006/HB4, 9012): These types typically have one lamp bead on each side of the lamp body, totaling two lamp beads. When in use, all light beads are illuminated.
- Dual Lamps (e.g., H4/9003/HB2, 9004/HB1, 9007/HB5, 9008/H13): These types typically have two beads on each side of the lamp body, totaling four beads. For general car models, half of the light bulbs are on during high beam and the other half are on during low beam. For some special car models, all light beads may illuminate for high beam.

3. Installation Guide
3.1 General Installation Steps
- Turn off the vehicle power and allow the headlights to cool down completely.
- Open the engine compartment. Locate the rear cover of the headlights.
- Turn the rear cover counter-clockwise and remove the original car light bulb.
- Insert the LED light into the original light socket, paying attention to the positive and negative directions. Ensure the buckle is securely in place.
- After powering on, check if the lighting is normal. Adjust the lens angle to meet the regulatory illumination range (low beam tangent level).
3.2 Installation Diagram for H11/9005/9006/9012/880 Types
- Open the front cover of the vehicle and prepare to install the LED headlights.
- Find the original car bulb. Unscrew it.
- Remove the original car bulb.
- Place the LED bulb in its original position.
- Twist the LED bulb until it fits and is secure.
- Connect the power supply and test if it works properly.

3.3 Installation Diagram for H1/H3/H4/H7/H13/9004/9007 Types
- Open the front cover of the vehicle and prepare to install the LED headlights.
- Find the original bulb location.
- Open the spring clip, take out the original bulb and chuck.
- Install on the new chuck.
- Press the spring clip and make it firm.
- Aim at the chuck slot, put the bulb into the chuck.
- Notice the chuck slot, make it match with the convex position.
- Rotate slightly and make the bayonet fixed.
- Connect the power supply and test if it works properly.

3.4 Installation Precautions
- Put the vehicle into park or make sure it is securely in gear.
- Make sure to have the ignition turned off and the keys removed.
- Be careful to avoid burns, especially when turning on or off the vehicle's lighting.
- Make sure not to touch the lamp bead with your fingers, to avoid staining or damage. Do not press the fan to avoid damage to the fan.
- Pay attention to the positive and negative connections. Fully examine the connection of the contact points, ports, and wires, as faulty connections can cause lighting problems.
- Ensure that the end of the bulb does not come into contact with the interior light shield of the headlight when adjusting the bulb. The wires of the lights should be facing down.
- It is best to install a dust cover to prevent dust from affecting the headlight's service life.

4. Operation
Once installed, operate your vehicle's headlight switch as usual. The LED headlights are designed to provide optimal illumination for both low and high beam settings.
- For single lamp types (e.g., H7, H11), all lamp beads will illuminate when the headlight is on.
- For dual lamp types (e.g., H4, 9004), typically half of the lamp beads are active for low beam and the other half for high beam. In some special car models, all lamp beads may illuminate for high beam.

5. Maintenance
- Cooling Fan Inspection: Check the cooling fan for dust accumulation every 6 months. Clean if necessary to ensure optimal heat dissipation.
- Avoid Prolonged Lighting: If using the headlights for more than 4 hours continuously, intermittent shutdown is recommended to prolong lifespan.
6. Troubleshooting
- Headlight Not Working After Installation: If the headlight does not work after installation, try reversing the plug 180° and reconnecting it.
- Flickering or Errors: If the headlights are flickering or showing errors, it may be due to a current difference. Energy-efficient LED headlights require less current than halogen or xenon headlamps. In such cases, you may need to install a pair of decoders (CANBUS error cancellers) to resolve the issue.
- Voltage Stability: If flickering or extinguishing occurs, first check if the vehicle's voltage is stable at the appropriate standard voltage (12V or 24V).
- Incompatible Vehicle Models: These LED headlights are suitable for most cars but are not 100% error-free for all models. Specific car brands like VW Touareg, Opel, Seat Altea, Audi A4 B6, Audi A6, Volkswagen Jetta, and Golf may require special decoders. Without a decoder, the automobile dashboard might display failure warnings or interfere with the radio.
7. User Tips
- Halogen Replacement: These LED headlights can generally replace halogen lights. However, be prepared to install a decoder if you experience flickering or error messages, especially in newer or sensitive car models.
- Socket Type Verification: Always double-check your car's existing headlight socket type (e.g., H7, H4, H11) before purchasing to ensure compatibility. If unsure, consult your car's manual or a professional.
- Professional Installation: If you are not comfortable with automotive electrical work, consider professional installation to avoid potential issues.
8. Warranty and Support
This product comes with a 1-year warranty from the date of purchase. The warranty covers manufacturing defects and material faults under normal use. Please retain your proof of purchase for warranty claims.
For further assistance or to view the original user manual in PDF format, please refer to the following link: User Manual (PDF).