LAUNCH Creader Elite 2.0

Contents

LAUNCH X431 Creader Elite 2.0 OBD2 Scanner User Manual

Comprehensive Guide for Diagnostic Tool Operation

1. Introduction

The LAUNCH Creader Elite 2.0 is an advanced smart code reader designed for professional technicians and DIY enthusiasts. This tool is specifically engineered for passenger cars with 12V battery voltage, particularly compatible with Mercedes Benz, Sprinter, and Maybach series vehicles. It offers a wide range of diagnostic functions and services to help identify and resolve automotive issues efficiently.

This manual provides detailed instructions on how to set up, operate, maintain, and troubleshoot your Creader Elite 2.0 device. Please read all instructions carefully before use to ensure safe and effective operation.

2. Safety Information

WARNING: To help prevent personal injury, always follow these safety precautions:

  • Never use this tool for any application other than its designed purpose.
  • Do not alter or modify this tool in any way. Improper operation or modification can result in serious injury or death.
  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle, as this can cause driver distraction and lead to accidents.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area; exhaust gases are poisonous.
  • Place blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs due to hazardous voltages when the engine is running.
  • Ensure the transmission is in Park (P) for automatic transmission (A/T) or Neutral (N) for manual transmission (M/T), and the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
  • Keep this tool dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth for cleaning.

3. FCC Compliance Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio / TV technician for help.

4. Product Overview

4.1 Components & Controls

LAUNCH Creader Elite 2.0 device with main screen showing Diagnose, OBD II, Upgrade, Mall, and Settings icons.
Figure 4-1: LAUNCH Creader Elite 2.0 Main Unit. The device features a touch screen, diagnostic cable, and various control buttons.
Table 4-1: Components and Controls
No.NameDescription
1Touch screenDisplays test results and user interface.
2Charging portConnects to PC via data cable for power.
3Diagnostic cableConnects to the vehicle's DLC port for power and communication.
4Settings buttonQuick access to the Settings module.
5HOME buttonNavigates to the home (Job menu) screen.
6BACK buttonExits the current program or returns to the previous screen.
7Memory card slotCurrently disabled and reserved for future use.

4.2 Technical Specifications

  • Screen: 4" touch screen with a resolution of 480*800
  • CPU: 4-core 1.3GHz processor
  • RAM: 1GB
  • ROM: 16GB
  • WiFi: 802.11b/g/n 2.4GHz
  • USB: TYPE C
  • OBD II input voltage range: 9~18V
  • Power up via: DC 5V data cable or Diagnostic cable through connection to vehicle's DLC
  • Working temperature: -10 to 50°C (14 to 122 F°)
  • Storage temperature: -20 to 70°C (-4 to 158 F°)

4.3 Accessories Checklist

The standard package includes:

  • Creader Elite special car scanner (Main Unit)
  • Data cable (OBD2 Cable)
  • User manual (this document)
  • Quick Start Guide
Image showing the contents of the Creader Elite 2.0 package: Main Unit, OBD2 Cable, User Manual, and Quick Guide.
Figure 4-2: Creader Elite 2.0 Scan Tool Accessory List.

5. Initial Setup

5.1 Powering Up The Tool

There are two methods to power up the Creader Elite 2.0:

  1. Via Data Cable: Plug one end of the included data cable into the charging port of the tool, and the other end to a PC.
  2. Via Diagnostic Cable: Insert the diagnostic cable into the vehicle's Data Link Connector (DLC) port.

When the tool is powered on, the screen will automatically light up.

5.2 Getting Started (First-time Use)

For first-time users, follow these steps to configure the system settings:

  1. Power on the tool. The welcome page will appear. Tap “Start” to proceed.
  2. Choose the desired system language, then tap "Next".
  3. Select the desired time zone, and tap “Next” to enter the WLAN setup screen.
  4. Slide the WLAN switch to ON. The system will search for available wireless networks. Choose your desired WLAN access point/network.
    • If the chosen network is open, you can connect directly.
    • If the selected network is encrypted, enter the correct security key (network password).

    Note: If you choose "Ignore" during WLAN setup, the tool will proceed to the date setting page. If connected to the Internet, the system will automatically obtain the correct network date and time.

  5. After network connection, tap “Next Step" to configure workshop information. Input the required details, and tap "Next Step".

    Note: Configured workshop information will be appended to every successfully generated report.

  6. Read the user agreement carefully, check the box "Agree to all the above terms”, and tap “OK” to finish the sign-up process and navigate to the Job Menu.

The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16-pin connector used to interface diagnostic tools with the vehicle's on-board computer. It is usually located within 12 inches of the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary.

Diagram showing common DLC locations in a car dashboard, labeled A through F.
Figure 5-1: Common Data Link Connector (DLC) Locations.
Table 5-1: DLC Location Examples
LabelVehicle Models
AOpel, Volkswagen, Audi
BHonda
CVolkswagen
DOpel, Volkswagen, Citroen
EChangan
FHyundai, Daewoo, Kia, Honda, Toyota, Nissan, Mitsubishi, Renault, Opel, BMW, Mercedes-Benz, Mazda, Volkswagen, Audi, GM, Chrysler, Peugeot, Regal, Beijing Jeep, Citroen and other most popular models

If the DLC cannot be found, refer to the vehicle's service manual for the location.

6. Operation

6.1 Connecting to Vehicle

  1. Turn the vehicle ignition OFF.
  2. Locate the vehicle's DLC port (refer to Section 5.3).
  3. Plug the diagnostic cable into the vehicle's DLC port.

    Notes:

    • A plastic DLC cover may need to be removed for some vehicles.
    • The cable connector is keyed and will only fit one way. If you have difficulty, rotate the connector 180° and try again.
  4. Turn the ignition ON. DO NOT start the engine.

6.2 Job Menu Overview

The main Job Menu includes the following function modules:

  • Diagnose: Configures the tool for professional diagnostic functions.
  • OBD II: Provides quick access to check DTCs, MIL status, monitor readiness, and other emission-related services.
  • Reset: Allows performing various common special functions (e.g., ABS Bleeding, Injector Coding, Battery Match, Gear Learning, Sunroof Initialization, Oil Reset, TPMS Reset, Throttle Calibration, Brake Reset, Camshaft Relearn, D-P-F Reset, IMMO Reset, AFS Reset, A/C Relearn, Seats Calibration, EPB Reset, Air Level Calibration).
  • Upgrade: Used to update diagnostic software and APK online. Requires a stable network connection.
  • Mall: Allows purchasing additional diagnostic software with full system and functions not pre-installed.
  • Settings: Manages data and system settings like Network setup, Workshop information, and Brightness.
Screenshot of the LAUNCH Creader Elite 2.0 main menu showing Diagnose, OBD II, Upgrade, Mall, and Settings icons.
Figure 6-1: Main Job Menu of the Creader Elite 2.0.

6.3 System Diagnosing

This function is designed to diagnose electronic control systems of a single vehicle model.

Notes:

  • The diagnostic software includes various reset functions, accessible directly within this module.
  • Diagnostic software use is free forever, but free updates are for the first year. Renew subscription for newer software.
  • More vehicle coverage can be extended via the "Mall" function.

6.3.1 Smart Diagnosis (Auto-Detect)

After connecting the tool and turning the ignition ON, the system automatically enters auto-detect mode (ensure "Automatic detection on connect" in "Settings" is ON).

Note: A stable network connection is highly recommended for accurate VIN detection.

Caution: Do not connect or disconnect any test equipment with ignition on or engine running.

  1. If the system successfully obtains the VIN (Vehicle Identification Number), it will scan vehicle systems. A diagnostic report will be automatically generated in Settings -> Data -> Diagnostic Report.
  2. If VIN information cannot be accessed, a prompt will appear for manual VIN input.

6.3.2 Manual Diagnosis

If auto-detect fails, you can perform manual diagnosis. Follow the on-screen instructions to select the vehicle model, year, and system manually.

Note: Diagnostic menus may vary between vehicle vendors.

Flowchart illustrating the manual diagnosis process: Select Diagnose -> Select Vehicle Manufacturer -> Select Test Function (Read version info, Read fault code, Clear fault code, Read data stream) or Select Test System (Automatic or Manual Select).
Figure 6-2: Manual Diagnosis Flowchart.

Steps for Manual Diagnosis (Example using DEMO):

  1. Select diagnostic software version: Tap "DEMO".
  2. Select vehicle model: Choose the desired vehicle model (e.g., "For BENZ Series").
  3. Turn the ignition key to ON.
  4. Read vehicle information: Verify the displayed vehicle information. If correct, tap “Yes” to continue.
  5. Select test item: Choose from "Health Report", "System Scan", or "System Selection".

6.3.3 Health Report (Quick Test)

This function quickly accesses all electronic control units (ECUs) and generates a detailed vehicle health report. Systems with fault codes are marked with a red cross, while OK systems have a green tick.

  • Report: Tap to save the diagnostic result.
  • Clear Code: Tap to clear existing diagnostic trouble codes.

6.3.4 System Scan

Quickly scans which systems are installed on the vehicle.

6.3.5 System Selection

Manually select the test system and function step-by-step.

6.4 OBD II Diagnosis Functions

Access these functions from the Job Menu by tapping "OBD II".

  • Read Codes: Identifies which section of the emission control system has malfunctioned.
  • Erase Codes: Clears retrieved codes after repairs. Ensure ignition is ON and engine is OFF.

    Notes:

    • Record trouble codes before clearing.
    • Clearing codes does not fix the problem; proper repairs are necessary.
  • I/M Readiness: Indicates if emission-related systems have been evaluated and are ready for Inspection and Maintenance testing.
  • Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU.

    Display Modes:

    • Value: Default mode, displays parameters in text list format.
    • Graph: Displays parameters in waveform graphs.
    • Combine: Merges up to 4 waveform graphs for data comparison.
  • View Freeze Frame: Records a snapshot of vehicle operating parameters when an emission-related fault occurs, aiding in problem identification.
  • O2 Sensor Test: Displays results of the ECU's last O2 sensor test.
  • On-Board Monitor Test: Reads results of on-board diagnostic monitoring tests for specific components/systems.
  • EVAP System Test: Initiates a leak test for the vehicle's EVAP system. Refer to the vehicle's service repair manual for procedures.
  • Vehicle Info: Displays vehicle information such as VIN, CID (Calibration ID), and CVN (Calibration Verification Number).
Image showing various OBD II functions icons: Read Codes, Erase Codes, View Live Data, View Freeze Frame, Turn Off MIL, O2 Sensor Test, EVAP System Test, I/M Readiness, Vehicle Information, On-Board Monitor Test, and More.
Figure 6-3: OBD II Functions for All Car Makes.

6.5 Reset (Special Functions)

The Creader Elite 2.0 supports numerous special reset functions. These functions require specific software subscriptions.

Image showing various full service functions: ABS Bleeding, Injector Coding, Battery Match, Gear Learning, Sunroof Initialization, Oil Reset, TPMS Reset, Throttle Calibration, Brake Reset, Camshaft Relearn, D-P-F Reset, IMMO Reset, AFS Reset, A/C Relearn, Seats Calibration, EPB Reset, Air Level Calibration.
Figure 6-4: Full Service Functions.

Key Programming Functions:

  • All Key Lost
  • Add New Key
  • Disable & Delete Key
  • Anti-theft Module Matching

Notice: Key programming is ONLY for cars with easy IMMO systems. Contact ediaqtools@hotmail.com to check compatibility.

Image showing key programming functions and bi-directional active test functions like Turn On/Off The Light, Injector Buzz Test, Operate The Mirror, A/C Activation, Wiper Test, Turn On/Off Radiator Fan, Test Door Lock Actuators, Open/Close The Windows, Fuel Pump Test, Turn On/Off The Sound Horn.
Figure 6-5: Key Programming and Bi-Directional Active Test Functions.

6.5.1 Subscribe Reset Software

By default, no reset software is included. You must go to the “Mall” on the Job menu to subscribe. Subscriptions are valid for one year from the date of purchase. After expiration, renewal is required to access newer software.

6.5.2 Perform Reset Procedures

There are two methods: Manual Reset and Auto Reset.

  • Auto Reset: Sends commands from the tool to the vehicle's ECU for resetting.
  • Manual Reset: Guides users through on-screen instructions to select options, enter data, and perform necessary actions.

Flowchart for Reset Procedures:

  1. Select "Reset"
  2. Choose the desired service function
  3. Select the desired car brand
  4. Select the reset mode (mode availability varies by vehicle)
  5. Follow the on-screen instructions to proceed

7. Maintenance

7.1 Upgrade Diagnostic Software & App

This function allows you to update the diagnostic application and software. While pre-installed software is free to use indefinitely, free updates are typically for the first year. Renewing your subscription ensures access to the latest software versions, offering improved service, functions, and experience.

To update, tap "Upgrade" on the Job menu to enter the update center. Ensure a strong and stable Wi-Fi connection.

By default, all diagnostic software is selected for update. You can deselect specific software by tapping "Unselect" and unchecking the vehicle model. Tap "Update" to begin downloading. The process may take several minutes. Once downloaded, software packages will install automatically.

7.2 Renew Subscription

After the free update period expires, the current version of diagnostic software can still be used. However, to get the latest diagnostic software, you need to renew the subscription. Tap "Upgrade" on the Job menu to enter the update center.

Software with expired subscriptions will be displayed in gray. Tap to select the desired diagnostic software, and a popup will appear. Tap "Renew" and input the 24-digit pin code from your Subscription Renewal Card (purchased from your local dealer). Tap "Submit" to complete the renewal. The latest diagnostic software will then be ready for use.

Note: A single Subscription Renewal Card is applicable to one software, not all software installed on the tool.

8. Settings

The Settings menu allows you to customize various aspects of your Creader Elite 2.0:

  • Units of measurement: Set to Metric System or English System.
  • Automatic detection on connect: Enable/disable automatic VIN detection upon connection to the vehicle's DLC.
  • Brightness: Adjust screen brightness. Reducing brightness helps conserve power.
  • Sound: Adjust volume and other sound settings.
  • Network: Configure WLAN settings. Turn off WLAN when unused to save battery power.
  • Time Zone: Set the device's time zone.
  • Language: Change the system language.
  • Workshop information: Add a personalized tag to diagnostic reports.
  • Recovery: Reset the tool to default factory settings.

    Warning: Resetting may cause data loss. Back up important data before performing this operation.

  • Clean Up: Clear cache files and free up storage space. The tool will reboot automatically after cleanup.
  • Screen Capture: Enable a floating screenshot icon. Screenshots are saved under Settings -> Data -> Image.
  • About: Displays hardware configuration and license agreement.
  • Data: Manages diagnostic records, reports, DTC library, DLC location images, feedback, and firmware fixes.
    • Diagnostic Record: View recorded running parameters or waveform graphs.
    • Diagnostic Report: Stores all generated diagnostic reports. Reports can be filtered and deleted.
    • DTC Library: Retrieve detailed descriptions of Diagnostic Trouble Codes.
    • DLC (Data Link Connector) Location: Helps find the vehicle's DLC.
    • Image: View and manage screenshots.
    • Feedback: Submit diagnostic problems for analysis and troubleshooting.
    • Firmware Fix: Upgrade and fix diagnostic firmware. Do not cut power during this process.
    • User Manual: Access the integrated user manual.

9. Troubleshooting (FAQ)

Here are some frequently asked questions and their solutions:

Q: System halts when reading data stream. What is the reason?
A: This may be caused by a slackened connector. Turn the tool off, firmly connect the connector, and switch it on again.
Q: Screen of the tool flashes at engine ignition start.
A: This is caused by electromagnetic disturbing and is a normal phenomenon.
Q: There is no response when communicating with the on-board computer.
A: Confirm proper power supply voltage. Check if the throttle is closed, the transmission is in neutral, and the water temperature is proper.
Q: What to do if the system fails to start auto VIN detection?
A: Check the following:
  • Ensure the tool is properly connected to the vehicle's DLC port.
  • Verify that the “Automatic detection on Connect” switch in Settings is ON.
Q: Why are there so many fault codes?
A: Usually, this is caused by poor connection or fault circuit grounding.
Q: How to upgrade the system?
A: Follow these steps:
  1. Switch the tool on and ensure a stable internet connection.
  2. Tap "Settings" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version” to enter the system upgrading page.
  3. Follow the on-screen instructions. The process may take several minutes. After a successful upgrade, the tool will automatically restart and return to the Job menu.

10. User Tips

  • For optimal performance and access to the latest features, ensure your device software is regularly updated.
  • When performing diagnostics, always double-check the connection to the vehicle's OBD2 port to avoid communication issues.
  • If you encounter issues with auto VIN detection, try manually entering the VIN or checking the "Automatic detection on Connect" setting.
  • Remember that clearing fault codes only removes the indicator; the underlying problem must be repaired to prevent recurrence.

11. Warranty and Customer Support

11.1 Warranty Information

This LAUNCH® electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH® products for purposes of resale or use in the ordinary course of the buyer's business.

The warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by LAUNCH in accordance with stipulated procedures.

11.2 Customer Service

If you have any questions regarding the operation of the unit, please contact your local dealer or the customer service center:

  • Telephone: 86-755-25938674
  • E-mail: DOD@cnlaunch.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.