1. Product Overview
The FOXSUR FBT200 is a smart battery tester designed to analyze the health and charge status of 12V and 24V lead-acid batteries. It provides quick and accurate readings for various battery parameters, helping you diagnose potential issues and ensure optimal battery performance.
Key Features:
- Supports 12V and 24V batteries.
- Tests various battery types: VRLA, GEL, AGM, EFB, STD (Regular Flooded).
- Measures Internal Resistance, Battery Voltage, CCA Value, Status of Charge (SOC), and Status of Health (SOH).
- Features reverse connection protection.
- Compact and portable design.
2. Setup and Connections
Before using the FBT200, ensure the battery terminals are clean and free of corrosion for accurate readings.
Connecting the Tester:
- Identify the positive (+) and negative (-) terminals on your vehicle battery.
- Connect the red positive (+) clamp of the FBT200 to the positive (+) battery terminal.
- Connect the black negative (-) clamp of the FBT200 to the negative (-) battery terminal.
- The tester will power on automatically once correctly connected to a battery with sufficient voltage (above 8V).
Controls and Display:
- Up Arrow: Previous item, or increase battery rating values.
- ESC (Escape): Cancel button.
- Down Arrow: Next item, or decrease battery rating values.
- ENTER: Confirm; Enter and proceed.
- RESET: Reset / Restart.
- Positive battery test clamp.
- Negative battery test clamp.
3. Operating Instructions
The FBT200 allows for quick and comprehensive battery analysis. Follow these steps to perform a test:
- Connect the Tester: As described in Section 2, connect the red clamp to the positive terminal and the black clamp to the negative terminal of the battery.
- Select Test Program: Use the Up/Down arrow buttons to navigate through the menu options.
- Input Battery Parameters: Select the correct battery type (VRLA, GEL, AGM, EFB, STD) and input the Cold Cranking Amp (CCA) value as marked on your battery label. Use the Up/Down arrows to adjust values and ENTER to confirm.
- View Test Results: The tester will display results within approximately 3 seconds.
Interpreting Results:
The FBT200 provides detailed information about your battery's condition:
- Internal Resistance (I.R): Indicates the battery's ability to deliver current. Lower values are better.
- Battery Voltage (VOLT): The current voltage of the battery.
- CCA Value (EDC): The measured Cold Cranking Amps, crucial for starting performance.
- Status of Charge (SOC): Percentage of charge remaining in the battery.
- Status of Health (SOH): Overall health percentage of the battery, indicating its remaining lifespan and performance capability.
Product Demonstration Video:
4. Maintenance
To ensure the longevity and accuracy of your FBT200 battery tester, follow these maintenance guidelines:
- Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Storage: Store the tester in a dry environment, away from direct sunlight and extreme temperatures.
- Cable Care: Avoid bending or kinking the test cables excessively. Inspect clamps and cables regularly for damage.
5. Troubleshooting
Here are solutions to common issues encountered with the FBT200:
- No Display:
- Ensure the battery voltage is higher than 8V. The tester is powered by the battery being tested.
- Verify that the positive and negative clamps are connected correctly to the battery terminals. - Inaccurate Test Results:
- Confirm that the battery type and CCA values entered into the tester match the specifications on the battery label. Incorrect input parameters will lead to inaccurate readings. - FBT-200 Does Not Charge Batteries:
- The FBT200 is a battery analyzer and tester only; it does not have charging capabilities. - FBT-200 Does Not Have Internal Power:
- The device operates solely by drawing power from the battery it is testing. It does not contain an internal battery.
6. Specifications
| Feature | Specification |
|---|---|
| Display | 2.7" LCD |
| Cable Reach | 650mm (25.6 inches) |
| Storage Temperature | -20°C to +70°C (-4°F to 158°F) |
| Working Temperature | -20°C to +60°C (-4°F to 140°F) |
| Dimensions (L*W*H) | 150*90*35mm (5.9*3.54*1.38 inch) |
| Weight | 325g (0.72lb) |
| Supported Battery Types | VRLA, GEL, AGM, EFB, STD (Regular Flooded) |
| Voltage Range | 12V and 24V |
| Test Range | 3Ah - 200Ah |
| Certifications | CE, RoHS, FCC |
Wide Application:
The FBT200 is suitable for a broad range of vehicles and battery types, including:
- Electric vehicles and motorcycles
- Cars and SUVs
- Trucks, engineering vehicles, and agricultural vehicles
- Various lead-acid, colloid, start-stop batteries (AGM/GEL)
7. User Tips
- Always refer to your battery's label for accurate type and CCA values before testing to ensure precise results.
- The FBT200 is a diagnostic tool, not a charger. If your battery is low, it will need to be charged separately.
- Regularly check your battery's health and charge status, especially before long trips or during extreme weather conditions, to prevent unexpected breakdowns.
- Ensure a firm connection of the clamps to the battery terminals to avoid false readings.
8. Warranty and Support
The FOXSUR FBT200 battery tester is certified with CE, RoHS, and FCC standards, ensuring quality and safety. For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase for warranty claims.
