1. Introduction
The LAUNCH X431 Creader Elite V2.0 FGC is an intelligent and networkable diagnostic tool designed for professional technicians and DIY enthusiasts. It provides comprehensive diagnostic services for various vehicle systems.
1.1 Vehicle Coverage
This diagnostic device is specifically designed to work with all OBD II compliant vehicles, including those with Controller Area Network (CAN). EPA regulations require all 1996 and newer vehicles (cars and light trucks) sold in the United States to be OBD II compliant, encompassing American, Asian, and European vehicles.
A small number of 1994 and 1995 model year gasoline vehicles are also OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the following:
- Vehicle Emission Control Information (VECI) Label: This label is usually located under the hood or on the radiator of most vehicles. If the vehicle is OBD II compliant, the label will state "OBD II Certified."
- Data Link Connector (DLC): Legal regulations require all OBD II compliant vehicles to have a "common" 16-pin Data Link Connector (DLC).
Note: Some 1994 and 1995 vehicles have 16-pin connectors but are not OBD II compliant. Only vehicles with a Vehicle Emission Control Information label indicating "OBD II Certified" are OBD II compliant.
1.2 OBD II Definitions
The following terms and their definitions relate to OBD II systems:
- EOBD: European On-Board Diagnostics. Essentially the same as OBD II, using the same data link connector and communication protocols.
- Communication Protocols: Enables communication between various systems and sensors in a vehicle. Currently, there are five protocols: CAN-Bus, J1850 VPW, ISO 9141-2, J1850 PWM, ISO 14230 KWP.
- PCM (Powertrain Control Module): The term accepted by OBD II for the vehicle's "on-board computer." In addition to controlling engine management and emission systems, the PCM also controls powertrain (transmission) operation. Most PCMs can also communicate with other vehicle computers (ABS, traction control, body, etc.).
- DLC (Data Link Connector): The 16-pin connector on the vehicle that allows communication between the computer system and the diagnostic device.
- MIL (Malfunction Indicator Lamp): The vehicle's "Check Engine" warning light, which activates when a DTC is stored.
- DTC (Diagnostic Trouble Code): A code stored in the computer system's memory that helps identify the fault condition causing the MIL to activate.
- Freeze Frame Data: Operating conditions stored when a DTC is recorded.
- PID (Parameter Identification Data): Data returned by the vehicle's control modules to the diagnostic device.
- Monitors: "Diagnostic routines" programmed into the PCM. The PCM uses these programs to perform diagnostic tests and monitor the operation of emission-related components or systems to ensure they function correctly and within manufacturer specifications.
- Enabling Criteria: Also called enabling conditions. These are vehicle-specific events or conditions that must occur within the engine before the various monitors can be set or run. Some monitors require the vehicle to follow a prescribed "drive cycle" routine as part of the enabling criteria. Drive cycles vary between vehicles and for each monitor in a specific vehicle. Refer to the vehicle's workshop manual for specific enabling procedures.
- Drive: A drive for a specific monitor requires the vehicle to be driven in such a way that all necessary "enabling criteria" are met for the monitor to run and complete its diagnostic tests. The "drive cycle" for a specific monitor begins when the ignition key is turned to "ON." It is successfully completed when all "enabling criteria" for the monitor's operation and completion of its diagnostic tests are met, and the ignition key is turned to "OFF." Since each of the fifteen monitors is designed to perform diagnostics and tests on a different part of the engine or emission system, the "drive cycle" required for execution and completion is different for each individual monitor.
- Drive Cycle: A specific vehicle operating mode that provides the conditions necessary to set all applicable readiness monitors to the "Ready" state. The purpose of completing an OBD II drive cycle is to force the vehicle to perform its on-board diagnostics. A type of drive cycle must be performed after DTCs have been cleared from the PCM's memory or the battery has been disconnected. By completing a vehicle's full drive cycle, readiness monitors are "set" so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. Information on vehicle-specific drive cycles can be found in the workshop manual.
- Warm-up Cycle: Vehicle operation after an engine shutdown period where the engine temperature rises by at least 22°C (40°F) from the temperature before starting and reaches at least 70°C (160°F). The PCM uses warm-up cycles as a counter to automatically clear a specific code and associated data from its memory. If no faults related to the original problem are detected within a certain number of warm-up cycles, the code is automatically cleared.
- FT (Fuel Trim): Feedback adjustments to the basic fuel plan. Short-term fuel trim refers to dynamic or immediate adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration plan than short-term trim adjustments. These long-term adjustments compensate for vehicle differences and gradual changes that occur over time.
1.3.1 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are codes stored by the on-board computer's diagnostic system in response to a problem detected in the vehicle. These codes identify a specific problem area and are intended to give you a clue as to where a fault might be in a vehicle. OBD II Diagnostic Trouble Codes consist of a 5-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character, a number, 0-3; the other three characters, a hexadecimal character, 0-9 or A-F, provide additional information about where the DTC originated and what operating conditions set it. Below is an example illustrating the structure of the digits:

Example of a Diagnostic Trouble Code (DTC) structure.
P0201 - Injector Circuit Malfunction, Cylinder 1
1.3.2 Data Link Connector (DLC) Position
The DLC is typically a 16-pin connector used to connect the diagnostic code reader to the vehicle's on-board computer. In most vehicles, it is located within 12 inches of the center of the dashboard, under or around the driver's side. In some vehicles with special designs, the position of the DLC may vary.

Common DLC locations in various car models.
A - Opel, Volkswagen, Audi
B - Honda
C - Volkswagen
D - Opel, Volkswagen, Citroen
E - Changan
F - Hyundai, Daewoo, Kia, Honda, Toyota, Nissan, Mitsubishi, Renault, Opel, BMW, Mercedes-Benz, Mazda, Volkswagen, Audi, GM, Chrysler, Peugeot, Regal, Beijing Jeep, Citroen and other popular models
2. Safety Information
WARNING: Read, understand, and follow all instructions provided with this product. Read these instructions carefully before installing, operating, maintaining, or repairing this device. Keep this manual in a safe, accessible place.
To prevent injury:
- Never use this device for purposes other than those for which it was designed.
- Never alter or modify this device in any way. Improper operation and/or maintenance of the device or alteration of the device can lead to serious injury or death.
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the device while driving a vehicle. Operating or observing the device will distract the driver and can cause a fatal accident.
- Wear eye protection that complies with ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc., away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area: exhaust fumes are toxic.
- Place blocks in front of the drive wheels and never leave the vehicle unattended during tests.
- Exercise extreme caution when working near the ignition coil, distributor cap, ignition wires, and spark plugs. These components generate dangerous voltages when the engine is running.
- Place the gear in position P (for automatic transmission) or N (for manual transmission) and ensure the parking brake is engaged.
- Have a fire extinguisher suitable for gasoline/chemical/electrical fires readily available.
- Do not connect or disconnect the test device while the ignition is on or the engine is running.
- Keep this device dry, clean, free of oil/water or grease. If necessary, use a mild detergent on a clean cloth to clean the outside of the device.
3. Product Overview
3.1 Components & Controls

The LAUNCH X431 Creader Elite 2.0 FGC and its included accessories.
The package includes the main unit, a USB cable, a user manual, and a quick start guide.
| No. | Name | Description |
|---|---|---|
| 1 | Charging Port | Charges the device via a data cable (not included). |
| 2 | DB-15 Diagnostic Connector | Connects the diagnostic cable. |
| 3 | Power Button | Turns the device on/off. |
| 4 | Touchscreen | Displays test results. |
| 5 | BACK Button | Exits the current program or returns to the previous screen. |
| 6 | HOME Button | Navigates to the home screen (job menu). |
| 7 | Settings Button | Quick access to the settings module. |
3.2 Technical Specifications
- Screen: 4-inch touchscreen with a resolution of 800*480 pixels
- CPU: 4-core 1.3GHz processor
- RAM: 2GB
- ROM: 16GB (Note: JSON indicates 16GB, PDF indicates 32GB. Using 16GB from JSON as it's more specific to the product listing.)
- OBD II Input Voltage Range: 9~18V
- Power Up Via: DC 5V data cable (not included) or diagnostic cable connected to the vehicle's DLC
- Battery: 3000mAh
- WiFi: 802.11b/g/n 2.4GHz
- USB: TYPE-C
- Working Temperature: -10℃ to 45℃ (14℉ to 113℉)
- Storage Temperature: -20℃ to 70℃ (-4℉ to 158℉)
4. First Use and Setup
4.1 Powering On the Device
There are two methods to power on the device:
- Via Data Cable: Connect one end of the data cable (not included) to the device's charging port and the other end to a PC.
- Via Diagnostic Cable: Connect the diagnostic cable to the vehicle's DLC port. The screen will automatically light up when the device is powered on.
4.2 Initial Setup Steps
When using this device for the first time, you need to perform some system settings:
- Press the [POWER] button to turn on the device. A welcome page will appear on the screen. Tap "Start" to proceed.
- Select your desired system language and tap "Next Step."
- Select the time zone for your current location. The system will automatically configure the time according to your selected time zone.
- The system will automatically search for all available wireless networks. Select your desired wireless network.
- After the network connection is established, tap "Next Step" to configure the workshop information. Enter the required information and tap "Next Step" to proceed.
- Carefully read all terms of the user agreement, activate "I agree to all the above terms and conditions," and tap "OK" to complete the registration process. You will be automatically redirected to the job menu.
- Select the diagnostic software/reset software and download it.
Video: Unboxing and initial setup of the diagnostic tool.
5. Diagnostic Connection
Caution: Do not connect or disconnect test equipment while the ignition is on or the engine is running.
- Turn off the ignition.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 1.3.2 for common locations.
- Connect one end of the diagnostic cable to the vehicle's DLC and the other end to the DB-15 diagnostic connector on the device. Tighten the captive screws.
Notes:
- Some vehicles may have a plastic DLC cover that needs to be removed before connecting the diagnostic cable.
- The cable connector is keyed and will only fit in one direction. If you have trouble connecting the cable to the DLC, rotate the connector 180 degrees and try again.
- Turn on the ignition. The engine can be off or running.
6. System Diagnosis
This function is specifically designed to diagnose electronic control systems of individual vehicle models.
Notes:
- The vehicle's diagnostic software includes all types of reset software that the user can execute directly in this module (select Special Function from the diagnostic function list).
- All software is regularly updated. It is recommended to update and install the latest software version to get the best service, functions, and experience.
- The use and update of the diagnostic software you installed for the first time are free forever.
- The use and update of diagnostic software purchased in the "Mall" are free for one year. If the subscription expires, the user must renew it.
- Vehicle coverage can be expanded for each model. Simply go to "Mall" to subscribe.
6.1 Intelligent Diagnosis (Automatic Recognition)
This function allows you to quickly access the vehicle's electronic control systems by decoding the VIN, without manual step-by-step menu selection.
After connecting, turn the ignition key ON, and the system will enter automatic recognition mode.
Notes:
- Ensure that the "Automatic Recognition on Connection" option in "Settings" is set to ON.
- A highly stable and reliable network connection is recommended for successful VIN access.
A. Successful VIN Retrieval: Once the system has successfully retrieved the VIN (Vehicle Identification Number) information of the currently identified vehicle, confirm the VIN information to scan the vehicle systems until the diagnostic session is successfully completed.
B. Failed VIN Retrieval: If the device cannot access the VIN information, the following screen will be displayed:

Screen for manual VIN input when automatic recognition fails.
Enter the VIN and tap "OK." The system will automatically decode the VIN data and proceed with intelligent diagnosis if successful. Otherwise, the system will switch to manual diagnosis mode.
Notes:
- The most recognizable location for this number is in the upper left corner of the vehicle's dashboard. Other locations include the driver's door or pillar and the firewall under the hood.
- Generally, Vehicle Identification Numbers are standardized – all contain 17 characters. VIN characters can be uppercase letters A to Z and numbers 0 to 9; however, the letters I, O, and Q are never used to avoid misreading. No characters or spaces are allowed in the VIN.
6.2 Manual Diagnosis
If the device cannot retrieve or analyze VIN information, you can also perform a manual diagnosis. In this mode, you must follow the menu-driven command and then the on-screen instructions to proceed.
Notes:
- Before diagnosis, ensure that the corresponding vehicle manufacturer's software is installed on the device.
- The diagnostic menu may vary depending on the vehicle make, model, and year.
Refer to the flowchart below to manually diagnose a vehicle:

Flowchart for manual system diagnosis.
Take DEMO V15.34 as an example to demonstrate how to diagnose a vehicle.
Notes: The illustrations used in this manual are examples; the actual test screen may vary for each vehicle tested. The following illustrations are based on DEMO with basic functions. Vehicle diagnostic software with full systems and full functions can be purchased in the Mall.
- Select Diagnostic Software Version: Tap "DEMO" to proceed to step 2.
- Select Vehicle Model (varies by version): Select the desired vehicle model.
- Turn on Ignition: Set the ignition switch to ON.
- Read Vehicle Information: After reading the vehicle information, check if the vehicle information is correct. If yes, tap "Yes" to continue.
- Select Test Item: Select the desired test item to continue.
6.3 Health Report (Quick Test)
This function varies from vehicle to vehicle. It allows you to quickly access all electronic control units of the vehicle and generate a detailed report on the vehicle's condition.
On the test item selection screen, tap "Health Report." The system will begin scanning the ECUs. Once the scan is complete, the following screen will be displayed:

Example of a Health Report screen, showing fault codes and system status.
In the image above, the tested system with a fault code is marked with a red cross, and the system with OK is marked with a green checkmark. Buttons on the screen:
- Report: Tap here to save the diagnostic result as a report.
- Clear Code: Tap here to clear existing diagnostic trouble codes.
6.4 System Scan
This option allows you to quickly scan which systems are installed in the vehicle.
6.5 System Selection
This option allows you to manually select the test system and function step by step.
On the test item selection screen, tap "System Selection" and tap the desired system (e.g., "Engine") to access the test function selection screen.
Notes: Different vehicles have different diagnostic menus.
A. Read Fault Codes: This function displays detailed information about the DTC records retrieved from the vehicle's control system.
Tap "Read Fault Code" on the test function selection screen; the screen will display the diagnostic result.
Notes: Retrieving and using DTCs for troubleshooting vehicle operation is only part of a comprehensive diagnostic strategy. Never replace a part based solely on the DTC definition. Each DTC has a set of test procedures, instructions, and flowcharts that must be followed to confirm the problem location. This information can be found in the vehicle's workshop manual.
Buttons on the screen:
- Help: Tap here to view help information.
- Code Search: Tap here to search online for more information about the current DTC.
- Report: To save current data in text format. All diagnostic reports can be accessed via More -> My -> My Report.
B. Clear Fault Codes: After retrieving codes from the vehicle and performing specific repairs, you can use this function to clear the codes from the vehicle. Before performing this function, ensure that the vehicle's ignition key is in the ON position with the engine off.
Notes:
- If you plan to take the vehicle to a service center for repair, DO NOT clear the codes from the vehicle's computer. If data is deleted, valuable information that could help the technician troubleshoot may also be lost.
- Clearing DTCs does not fix the problem(s) that caused the code(s) to be set. If proper repairs are not made to fix the problem that caused the DTCs to be set, the code(s) will reappear and the "Check Engine" light will illuminate as soon as the problem that caused the DTCs to be set manifests itself.
C. Read Data Stream: This option retrieves and displays live data and parameters from the vehicle's ECU.
Tap "Read Data Stream" on the test function selection screen. The system will display the data stream items.
Buttons on the screen:
- Select All: Tap here to select all items on the current page. To select a specific data stream item, simply check the box next to the item name.
- Deselect All: Tap here to deselect all data stream items.
- OK: Tap here to confirm and proceed to the next step.
After selecting the desired items, tap "OK" to access the data stream reading page.
Notes:
- If the value of the data stream item is outside the range of the standard value (reference value), the entire row will be displayed in red. If it matches the reference value, it will be displayed in blue (normal mode).
- The 1/X display at the bottom of the screen indicates the current page/total number of pages. Swipe right/left across the screen to go to the next/previous page.
Three types of display modes are available for data display, allowing you to optimally view different types of parameters:
- Value: Displays parameters with numbers and lists.
- Graph: Displays parameters with waveform patterns.
- Combine: Graphs can be merged for easier comparison. In this case, different items are marked in different colors.
Report: Tap here to save the current data as a diagnostic report. All diagnostic reports can be accessed via More -> My -> My Report. The device logs the report date (date and time of report creation) and assigns a unique report number.
Record: Tap here to record and save live data. Recorded live data can serve as valuable information to help you troubleshoot and diagnose vehicle problems. All diagnostic records can be accessed via More -> Toolbox -> Diagnostic Record.
6.6 OBD II Diagnosis
This function provides a quick way to check DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status before emission certification testing, verify repairs, and perform a range of other emission-related maintenance tasks.
After the device is properly connected to the vehicle's DLC, tap "OBD II" in the job menu. The device will automatically start checking the vehicle's computer to determine the communication protocol used and then display the monitor status. Tap "OK." The following function list will be displayed.
- Read Codes: This function checks whether the various emission-related systems of the vehicle are functioning correctly and are ready for inspection and maintenance tests. It can also be used to check the monitor's running status and confirm that a vehicle fault has been correctly repaired.
- Read Live Data: This function retrieves and displays live data and parameters from the vehicle's ECU.
- Read Freeze Frame: This function creates a snapshot of operating conditions when an emission-related fault occurs.
- Read Fault Code: This function helps determine which section of the emission control system is malfunctioning.
- Clear Fault Codes: This function clears codes from the vehicle after codes have been retrieved and specific repairs have been performed. Before proceeding, ensure that the ignition key is in the ON position and the engine is off.
- Test Results: On-Board Monitoring Test: This function retrieves test results for emission-related powertrain components and systems that are not continuously monitored. The availability of the test is determined by the vehicle manufacturer.
- Control of On-Board Component/System Operation: This option is used to access tests of vehicle-specific subsystems and components. Available tests vary by vehicle manufacturer, year, and model.
- Read Vehicle Information: This function retrieves a list of information (provided by the vehicle manufacturer) from the vehicle's on-board computer. This information may include: VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
- EU OBFCM: This function displays a list of vehicle information provided by the vehicle manufacturer that complies with CO2 emission standards for new passenger cars and new light commercial vehicles (Regulation EU 2019/613). This information may include: Vehicle Identification Number, Total Fuel Consumption (Lifetime), and Total Driving Distance (Lifetime), etc.
6.7 History
Once a vehicle diagnosis has been performed, the device generally records all details of the diagnostic session.
The history function provides direct access to previously tested vehicles, and users can continue from the last operation without having to start over. On the main diagnostic screen, tap "History." All diagnostic records will be listed on the screen in chronological order.
7. Special Functions
The device offers coding, reset, relearn, and other service functions to restore vehicles to working condition after repair or replacement. Available tests vary by vehicle manufacturer, year, and model.
Due to continuous improvements, service functions may change without prior written notice. To access more service functions, it is recommended to check for updates regularly.
7.1 ECU Coding (Online & Offline)
The advanced coding function is used to re-flash vehicle control modules. This allows you to update the computer software on the vehicle to the latest version and reprogram adaptive data for certain components after repairs or replacements. This provides solutions for issues such as drivability, fuel efficiency, power loss, fault codes, and mechanical part durability. Please note that ECU coding is NOT universal for all vehicles; check compatibility with the VIN number before purchase.
7.2 Bi-directional Control (Active Test)
The device has bi-directional control capability and can perform Active Tests to access vehicle-specific subsystems and component tests. The tester sends commands to the ECU to drive actuators to determine the integrity of the system or parts by reading ECU data or monitoring actuator operation. For example, the X431 V can actuate relays, injectors, coils, or perform system tests. It will also actuate solenoid valves and actuators for active testing to easily identify errors. The bidirectional functions are quite extensive, even allowing you to open an EGR valve and observe the difference in idle response and oxygen sensor voltage. Please note: Active tests are NOT universal for all vehicles; check compatibility with the VIN number before purchase. Active tests vary depending on the manufacturer, year, and model, and only available tests are displayed in the menu.

Examples of Active Test functions, including Injector Kill Test, Fuel Pump & Valve Test, and Parking Brake Test.
7.3 31+ Reset Services
The device supports over 31 reset services to address various vehicle maintenance needs:

Overview of various reset functions supported by the device.
- Steering Angle Reset: Resets the steering angle to zero to keep the car running straight.
- Injector Coding: Writes the new injector code into the car system for correct cylinder injection quantity.
- IMMO (Immobilizer): Disables any lost keys and adds new keys. **ONLY for cars with an easy IMMO system.
- DPF Regeneration: Especially works for D-P-F system with D-P-F regeneration, D-P-F component replacement teach-in, and D-P-F teach-in after replacing the engine control unit.
- A/C Relearn: For when the vehicle air conditioner's electronic control unit is replaced, the actuator is replaced, or the memory of the electronic control unit is lost, requiring air conditioning initialization learning.
- ABS Bleeding: Helps exhaust air after repairing the ABS pump system.
- AdBlue Reset: Resets urea after the diesel exhaust treatment fluid is replaced or filled up.
- Throttle Matching: Initializes the throttle actuators to the default state.
- TPMS Reset: Displays sensor IDs from the vehicle's ECU, inputs TPMS sensor replacement IDs, and tests sensors.
- Tire Reset: Sets the size parameters of modified or replaced tires.
- AFS Headlamp Reset: Initializes the adaptive headlamp system.
- Sunroof Initialization: Initializes the sunroof when locked off or closed.
- Battery Reset: Registers the battery after replacement.
- Seat Calibration: Calibrates the memory in replaced or repaired seats.
- Oil Reset: Allows you to perform a reset for a new calculation of the Engine Oil Life system once the oil has been changed.
- A/F Reset: Sets or learns Air/Fuel ratio parameters.
- Gearbox Learn: Helps complete gearbox self-learning to improve gear shifting quality.
- Transport Mode: Deactivates the transport mode.
- Windows Calibration: Performs door window matching to recover ECU initial memory.
- Language Change: Changes vehicle system language.
- Suspension Reset: Adjusts the vehicle body height sensor for level calibration.
- NOx Sensor Reset: Resets catalytic converter learned value stored in ECU.
- Stop/Start Reset: Sets up the automatic start-stop function in ECU.
- Coolant Bleeding: Activates the electronic water pump.
- Brake Reset: Important for maintaining the safety and efficiency of the electronic braking system.
- Gear Learning: The scan tool monitors certain camshaft position sensor signals to determine if all conditions are met to continue with the procedure for engine running.
- ...and more.
7.4 Key Programming (IMMO)
The device supports key programming functions, particularly for vehicles with simpler immobilizer systems:
- Add & Disable Keys
- All Smart Keys Lost
- Rewrite Smart Keys
- Reset & Relearn Keys
- Replace Smart Key ECU
- Replace Knob Ignition

Key IMMO functions and Battery Register feature.
7.5 FCA AutoAuth Function
This function requires obtaining an account on the official FCA website first.
7.6 Battery Test Function
The device supports comprehensive battery testing:
- Evaluate the Battery Charge State
- Monitor the Closed-Circuit Current
- Replace New Battery with Same Parameters
- Register Battery Replacement
8. Full 10 OBD2 Functions
This scanner supports all 10 test modes for OBD-II cars, which are excellent for daily repair work. The table below describes the purpose of each mode of operation:

Visual representation of the 10 full OBD2 functions.
- Reading Codes: Shows the detailed description of Diagnostic Trouble Codes (DTCs).
- Erasing Codes & Reset: Turns off the Check Engine Light (MIL), clears codes, and resets monitors.
- Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically, and stores freeze frame data.
- I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
- Read Live Data Stream: Shows the information of continuous data stream from a vehicle in live graphic (waveform) display.
- View Freeze Frame Data: Checks the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
- O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
- On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
- Read Vehicle Information: Displays information such as VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number), etc.
- Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
9. Other Functions

Overview of additional professional diagnostic tools features.
- Auto VIN Scan (Smart Diagnosis): Adopts Auto-VIN technology that automatically recognizes vehicle information, making it easier to get the vehicle's make, model, and year information.
- Maintain Information (Powerful & Useful Function): This function provides how-to guides for some special functions, including examples of operating special functions for real vehicles to help you learn. It also offers Online Coding Help, showing steps for this function, and Channel Information, explaining how to perform basic settings to return the channel to its original normal value. All this maintenance information can assist you in better resolving vehicle issues.
- DTC Library: Allows you to retrieve the definition of diagnostic trouble codes from the extensive DTC database.
- Display Real-Time Battery Voltage: If the charging system is not working properly, the battery will not receive the proper charging voltage and could go flat. This OBDII scanner can display the instantaneous voltage across the battery terminals graphically. This helps you get early warnings for possible battery and charging system problems.
- Screenshot & Screen Recorder, Print Diagnostic Report: It is easy to save the diagnostic data you want, as well as the diagnostic report! It also supports printing diagnostic reports; scan the QR code to share first, then print.
10. Software Update & Subscription
This function allows you to update the diagnostic app and software. All software is regularly updated. It is recommended to update and install the latest software version to get the best service, functions, and experience.
- The use and update of the diagnostic software/reset software that the user installed for the first time are free forever. No subscription renewals are required.
- The use and update of diagnostic software/reset software purchased in the "Mall" are free for one year. If the free period expires, the user must renew the subscription. More information can be found in Section 10.2.
Note: Ensure that the network connection is strong and stable during the update.
10.1 Updating Diagnostic Software & App
Tap "Upgrade" in the job menu to access the Update Center.

Example of the software update screen.
By default, all diagnostic software is selected. To deselect specific software, tap "Deselect All" and then check the box next to the vehicle model. Tap "Update" to start the download. This may take a few minutes to complete. Please be patient. Once the download is complete, the software packages will be installed automatically.
10.2 Renewing Subscription
The use and update of software configurations purchased in the "Mall" are free for one year. If the free period expires, the current version of the software will be locked. To unlock it, the user must renew the subscription.
Tap "Upgrade" in the job menu to access the Update Center. If the free period has expired, a corresponding message will be displayed on the screen. Tap "Renew" to open the "Mall." Select the desired diagnostic software configuration and then follow the on-screen instructions to complete the update. The latest diagnostic software is now ready for use.
11. Toolbox / More Functions
The "More" section provides additional tools and features:
11.1 Diagnostic Software Deletion
This option allows you to delete diagnostic software that is not frequently used.
11.2 Firmware Fix
Use this module to update and repair the diagnostic firmware. Do not interrupt the power supply or switch to other interfaces during the upgrade process.
11.3 DTC Library
This function allows you to retrieve details of DTCs, significantly simplifying the diagnostic process.

Example of the DTC Library interface for searching trouble codes.
11.4 Diagnostic Record
This module stores operating parameters or waveform diagrams recorded by the user.
11.5 DLC (Data Link Connector) Position
This function helps you locate the DLC position in the vehicle.
11.6 Feedback
Use this function to send us feedback on your diagnostic problems for further analysis and troubleshooting.
11.7 Diagnostic Report
This module stores all diagnostic reports generated during the remote diagnosis process.
12. Settings
This module allows you to customize several system settings:
12.1 My Reports
With this option, you can view and manage your saved reports. All diagnostic reports are sorted by date and brand. If too many reports are saved, tap the search icon to filter and find them quickly.
12.2 Settings Module
- Units of Measurement: Set the unit of measurement. The metric system and the English system are available.
- Automatic Recognition on Connection: Determine whether automatic VIN recognition should start as soon as the device is properly connected to the vehicle's DLC.
- Brightness: Adjust the standby time and screen brightness.
- Sound: Adjust the volume and other sound settings.
- Network: Set up Wi-Fi networks that can be connected.
- Time Zone: Set the time zone.
- Language: The device supports multiple languages. Set your preferred language.
Note: After switching the language, re-download all diagnostic software, otherwise the system will use the English software by default. - Workshop Information: Set up the default email address for receiving diagnostic reports or screenshots, as well as workshop information.
Note: Once configured, the system will attach it to the report every time a report is successfully created. - Restore: Reset the device to factory default settings.
Warning: Resetting may result in data loss. Before doing so, please proceed carefully. - Clean: This option allows the user to delete some cache files and free up storage space. After cleaning, the device will restart automatically.
- Screenshot: Set whether the screenshot icon should be displayed on the screen. If this option is set to ON, a screenshot icon will float in the upper right corner of the screen. Tap it to capture the screen.
12.3 About
This option displays information about the device's hardware configuration and license agreement.
13. Troubleshooting / FAQ
This section lists some frequently asked questions and answers about this device.
- Is it safe to use? Yes, it has passed external testing certification.
- How durable is it? The product comes with a 5-year warranty, indicating its durability.
- What is its overall quality? It is a high-quality product with lifetime free updates and multiple functions such as engine analysis, ECU coding, bidirectional control, active test, Auto VIN scan, full OBD function, and battery test.
- What is the material quality? It is made of placits.
- How well does it perform? It performs well with functions like all system diagnosis, WiFi connectivity, ECU coding, bidirectional control/active test, and Auto VIN scan.
14. Maintenance
Keep this device dry, clean, free of oil/water or grease. If necessary, use a mild detergent on a clean cloth to clean the outside of the device.
15. User Tips
- For quick and efficient diagnosis, utilize the Auto VIN Scan feature to automatically identify your vehicle.
- When performing FCA AutoAuth functions, remember to obtain an account on the official FCA website first.
- Regularly check for software updates via WiFi to ensure you have the latest diagnostic functions and improvements.
- If you encounter any issues, refer to the DTC Library for detailed explanations of trouble codes, and use the Feedback function to report problems to LAUNCH support.
16. Warranty & Support
16.1 Warranty
This warranty is expressly limited to persons who purchase LAUNCH® products for resale or use in the normal course of the buyer's business. LAUNCH® electronic products are warranted to be free from material and manufacturing defects for one year (12 months) from the date of delivery to the user.
This warranty does not apply to parts that have been misused, altered, used for a purpose other than intended, or used in a manner inconsistent with the operating instructions. The exclusive remedy for a defective vehicle instrument is repair or replacement, and LAUNCH is not liable for consequential or incidental damages. The final determination of defects is made by LAUNCH according to established procedures.
16.2 Customer Service
If you have any questions while operating the device, please contact the seller or the LAUNCH TECH Service Center.
- Website: https://en.cnlaunch.com
- Phone: +86 755 8455 7891
- Email: overseas.service@cnlaunch.com
The product also comes with a 5-year warranty and lifetime free technical support.