Xhorse MultiProg

Contents

XHORSE MultiProg Extreme Programmer User Manual

Model: Multi-PROG

1. Introduction

This manual provides detailed instructions for the XHORSE MultiProg Extreme Programmer. It covers device functions, setup, operation, maintenance, and troubleshooting. Please read this manual carefully before operating the device to ensure proper usage and prevent damage.

The Multi-PROG is designed for automotive repair and module programming, supporting reading, writing, and cloning of common automotive MCUs, memory chips, electronic modules, and ECU computer boards.

2. Safety Precautions

To avoid personal injury, equipment damage, or vehicle damage, observe the following safety precautions:

  • Use the equipment in an environment with good electromagnetic compatibility.
  • Wear goggles that comply with ANSI standards.
  • Do not connect to a power supply that does not comply with specifications.
  • Disconnect the power supply when the equipment is not used or serviced for a long time.
  • Do not place the equipment in a humid, greasy, dusty, or other harsh environment.
  • Do not press, drop, or expose the equipment to direct sunlight.
  • Keep the equipment out of the reach of children.
  • This device is intended for legal use only for reading and writing chip and module data. Comply with national laws and do not use for illegal purposes.

3. Product Overview and Package Contents

The XHORSE Multi-PROG Extreme Programmer is a professional-level tool for automotive electronics. It features a 48-pin universal drive for high-speed programming.

XHORSE Multi-PROG Programmer with various accessories

Figure 3.1: XHORSE Multi-PROG Programmer and included accessories.

3.1 Main Functions

  • Memory Read/Write: Supports reading/writing of common memory chips (EEPROM, FLASH).
  • MCU Read/Write: Supports various brands of automotive MCUs.
  • Automotive Immo Module Read and Write: Supports common automotive immobilizer module data.
  • Engine ECU Read/Write: Supports various automotive engine ECU computer data, including checksum data processing.
  • Gearbox TCU Read/Write: Supports many types of automobile gearbox TCU computer data.
  • Third-party Script Function: Supports loading and utilizing software scripts for data processing and modification.
  • Batch Write Function: Supports factory mode for batch writing to chips, including offline write and file offline write.

3.2 Device Interfaces

Multi-PROG device interfaces labeled

Figure 3.2: Multi-PROG Device Interfaces.

  1. IC Locking Holder: Used for locking the chip holder to read chips.
  2. Status Indicator: Power indication and main unit working status.
  3. Main unit switch: Power on/off switch.
  4. Touch screen: For device operation and display.
  5. Magnetic shield: Magnetic design, quickly removable to replace adapter boards.
  6. Power socket: For connecting the power adapter.
  7. PE grounding plug: For grounding in specific environments (can be left vacant otherwise).
  8. ISP/ECU/DOIP interface: Integrated chip program, ECU computer program interface, supports DOIP protocol.
  9. Automation programming interface (reserved).
  10. RJ45 network port: For connection to PC software.
  11. USB A interface: For connection to PC software.
  12. USB B interface: For WIFI Network Card, U disk, and other devices.

3.3 Package Contents

The standard package includes the following items:

ItemNameQuantityRemark
1Multi-PROG1Multi-PROG programmer
2USB Cable1USB square port cable
3Power Adapter (15V 4A)1Power adapter
4220V Power Cord1220V AC input cable
5VH13 Interface Adapter Board1Chip holder adapter
6VH20 Interface Adapter Board1Interface self-test adapter
7VH23 Interface Adapter Board1Chip Soldering Adapter
8MCU Adapter Multi-PROG Solder Cable1MCU Read Soldering Cable
9MCU DB15 Adapter Cable1MCU Read Solder-free Adaptor Cable
10ECU Adapter Multi-PROG Solder Cable1ECU Read Soldering Cable
11ECU DB15 Adapter Cable1ECU Read Solder-free Adaptor Cable
12ECU Cable Plug1Suitable for different PIN sizes
13Multi-PROG OBD Cable1Multi-PROG OBD Cable
14USB WIFI Network Card1USB WIFI Network Card
15Product Manual1Product Manual
16Certificate Of Conformity1Factory inspection certificate and warranty certificate

Note: Some solder-free adapters and cables are not included in the standard package and may need to be purchased separately.

4. Setup and Connection

The Multi-PROG programmer consists of two main parts: the main unit and the PC software. The main unit can be connected to the PC software via a wired RJ45 network port or a USB port.

4.1 Connecting the Device to PC

  • Connect the Multi-PROG main unit to your PC using the provided USB Cable (USB A interface) or an Ethernet cable (RJ45 network port).
  • Connect the Power Adapter (15V 4A) to the power socket of the Multi-PROG and plug it into a power outlet.
  • Turn on the main unit using the main unit switch.
  • Install the Multi-PROG software on your PC. (Software: V1.1.5.0, Firmware: V1.2.1, Database version: V23. Lifetime Free Update online. Contact seller for download.)
Multi-PROG front view with screen

Figure 4.1: Multi-PROG Main Unit.

4.2 Using Adapter Boards and Cables

Various adapter boards and cables are provided for different programming tasks:

  • VH13 Interface Adapter Board: Used for locking various IC holders and DIP sealed memory chips for reading and writing.
  • VH20 Interface Adapter Board: Used for device interface self-test and diagnosis. Remove the magnetic shield and VH13 board, then insert VH20. Run the software's help/ZIF48 self-test menu.
  • VH23 Interface Adapter Board: For soldering 6-pin, 8-pin, and 16-pin chips for reading and writing.
  • MCU Adapter Multi-PROG Solder Cable / MCU DB15 Adapter Cable: Plug into the DB44 port of the device to read/write MCU chip data or automotive module data according to the wiring diagram.
  • ECU Adapter Multi-PROG Solder Cable / ECU DB15 Adapter Cable: Plug into the DB44 port of the device to read/write ECU module data according to the wiring diagram.
  • Multi-PROG OBD Cable: Plug into the OBD port of the car and select the corresponding model option in the software to read/write ECU and other module data directly.
  • ECU Cable Plug: 8 different types of plugs are available to connect various ECU pins.
Various cables and adapters for Multi-PROG

Figure 4.2: Multi-PROG Cables and Adapters.

5. Operating Instructions

This section details the primary operations of the Multi-PROG device.

5.1 EEPROM Read/Write Operation

EEPROM (Electrically Erasable Programmable Read-Only Memory) chips store electronic information data in vehicles. The Multi-PROG supports various interface connection methods for reading and writing these chips.

  1. Accessing EEPROM Function: Run the Multi-PROG software on your PC and navigate to the memory function menu.
  2. Model and Mask Query: Select the EEPROM manufacturer and specific model. The software will display all supported memory chip models. You can also use the search box to find models by chip model or silk screen mask (e.g., '5BBD' for 95320).
  3. Read, Write, and Check: The device provides functions to read, erase, write, and check EEPROM data. Click the corresponding button on the software interface. Be aware that erasing will permanently delete existing data.
Software interface for EEPROM Read/Write

Figure 5.1: EEPROM Read/Write Interface.

5.2 Microcontroller (MCU) Read/Write Operation

The MCU function is primarily used for data reading and writing of automotive electronic modules and computer modules. Proper wiring connections are crucial.

  1. Manufacturer Distinction: The device supports MCUs from various manufacturers like Atmel, Motorola, Freescale, Infineon, Renesas, and STMicroelectronics.
  2. Memory Area Division: MCUs typically have program, data, and configuration areas. Understand these divisions for correct operation.
  3. Wiring Diagram: The software provides wiring diagrams for basic read/write operations. Use a multimeter to identify correct connections for specific boards. Pay attention to optional low pins, pull-up resistors, and crystal frequency requirements as detailed in the software's wiring diagrams.
Microcontroller connected to Multi-PROG via wires

Figure 5.2: Example of MCU Wiring Connection.

5.3 Automotive Electronics Module Read/Write Operation

Multi-PROG supports reading and writing of immobilizer modules, dashboard modules, airbag modules, and other car body electronic modules.

  1. Module Selection: In the software, select the appropriate module type (e.g., IMMOBILIZER, DASHBOARD, AIRBAG) and vehicle model.
  2. Connection: Follow the specific circuit connection diagram provided in the software for the selected module.
  3. Operation: Perform backup, read, write, unlock, and lock operations as needed.

5.4 Automotive ECU Read/Write Operation

The device supports reading, writing, and cloning ECUs for various automobile brands, including Bosch, Siemens, Continental, Marelli, and Delphi.

  • Supported ECUs: Includes BMW MSV90, MSV80, B48/B58 series (ISN reading), Mercedes-Benz SIM271 series, and VW Bosch MED17 series.
  • Operation Steps (Example: BMW MSV90 ECU):
    1. Select 'ECU/BMW/1-Series' menu and then 'MSV90'.
    2. Connect according to the wiring diagram in the software, choosing the correct ECU cable plug.
    3. If ISN is required, it will be displayed after reading EEPROM. For cloning, read and save EEPROM and FLASH data, then write to the replacement ECU.
  • Operation Steps (Example: Mercedes-Benz SIM271 ECU):
    1. Select 'ECU/Mercedes/C-class' menu.
    2. Connect according to the wiring diagram in the software, choosing the correct ECU cable plug.
    3. For cloning, read and save EEPROM and FLASH data, then write to the replacement ECU.

5.5 Automobile TCU Read/Write Operation

The Multi-PROG supports TCU read/write for various brands and models.

  • Supported TCUs: Includes Volkswagen Audi Skoda DQ200, DQ250, VL381, Porsche DL501, Ford Dodge MPS6 series, BMW DKG, Mercedes-Benz VGS, and other models.
  • Operation Steps (Example: Audi A4 VL381 Series TCU):
    1. Select 'Transmission/Audi/VL381' module type.
    2. Connect according to the wiring diagram in the software, choosing the correct cable plug.
    3. For cloning, read and save EEPROM and FLASH data, then write to the replacement TCU.

5.6 Third-party Script Function

The device allows processing and saving of original data using third-party developed scripts before writing. The software provides a scripting interface for this purpose.

  • Using Scripts: After entering the read/write option, tap the script function, select 'Published Functions', and choose the desired script.
  • Script Development: Refer to the script development documentation provided with the software for methodology and examples.
Software interface for Third-party Script Function

Figure 5.3: Third-party Script Function Interface.

5.7 Chip Batch Write Function

Multi-PROG supports batch writing of chips, useful for factory production requiring large-scale writing. This function supports common memory and microcontroller series.

  • Usage: Refer to the documentation of the factory usage mode that comes with the software for specific instructions.

6. Maintenance

  • Keep the device clean and free from dust, grease, and moisture.
  • Store the device in a dry, cool place, away from direct sunlight.
  • Avoid dropping or subjecting the device to strong impacts.
  • Ensure the power supply used meets the specified voltage and current requirements (15V/4A).
  • Disconnect the power supply when the device is not in use or during maintenance.
  • For product maintenance and technical support, contact your dealer or download the Xhorse official APP to consult online customer service.

7. Troubleshooting

This section provides general guidance for common issues. For more specific problems, refer to the software's help documentation or contact support.

  • Device not powering on: Check the power adapter connection and ensure the power outlet is functional. Verify the main unit switch is in the 'ON' position.
  • Connection issues with PC: Ensure the USB cable or Ethernet cable is securely connected. Check PC drivers for the device. Try a different USB port or network cable.
  • Software not recognizing device: Verify the device is powered on and connected. Ensure the correct software version is installed and updated.
  • Read/Write errors:
    • Check all wiring connections according to the software's diagrams.
    • Ensure the correct adapter board and cable are used for the specific chip/module.
    • Verify the chip/module is correctly seated in the adapter or properly soldered.
    • Confirm the correct chip/module type is selected in the software.
    • For MCUs, check for specific wiring requirements like optional low pins or pull-up resistors.
  • Software freezing or crashing: Ensure your PC meets the minimum system requirements. Update the Multi-PROG software and firmware to the latest versions.

8. Specifications

ItemSpecification
Operating SystemLinux
ProcessorZYNQ7020 Dual Core Cortex A9 + FPGA
Memory256M*2 DDR + 64M NOR FLASH
Display3.5 inch, 320*480
Input Voltage15V/4A
Working Current300mA(14V)
Working Temperature-20~55℃
Storage Temperature-30~65℃
External InterfaceUSB/RJ45
DimensionsL233*W150*H54mm
Package Weight3.1 kg
Package Dimensions35cm x 25cm x 13cm

9. User Tips

  • Software Updates: The device offers lifetime free online updates for its software and firmware. Regularly check for updates to ensure compatibility and access to new features.
  • MQB48 License: The device comes with a free MQB48 license. To use the MQB48 NEC35XX function, bind your Multi-PROG and VVDI2 full version/Key Tool Plus Pad to the same Xhorse app account. Note that if using Key Tool Plus to read NEC35XX directly, a separate NEC35XX license might be required for the Key Tool Plus itself.
  • Quality Assurance: Users have noted the product's superior quality and durability, backed by a one-year warranty and CE certification.
  • Performance: The device performs perfectly for its intended functions of reading, writing, and cloning ECU/TCU.

10. Warranty and Support

10.1 Warranty Period

The warranty period for Multi-PROG devices is one year from the transaction date. If no transaction voucher is available or is lost, the manufacturer's factory date will prevail.

10.2 Warranty Exclusions

The warranty does not cover conditions resulting from:

  • Failure to use the machine in accordance with the instructions, leading to machine failure.
  • Damage to the machine due to self-repair or unauthorized modification.
  • Machine failure due to dropping, collision, or improper voltage.
  • Damage to the machine due to force majeure (e.g., natural disasters).
  • Malfunction or damage due to prolonged use in unsuitable conditions (e.g., on vehicles or ships).
  • Dirt and wear on the housing of the main unit due to normal use.

10.3 Technical Support

For product maintenance and technical support, please contact your dealer or download the Xhorse official APP. You can also consult online customer service or add the Skype account: live:.cid.1c698c9c01ec2482.

QR code for Xhorse APP download

Figure 10.1: Scan QR Code to download Xhorse APP.

Shenzhen Xhorse Electronics Co., Ltd. reserves all rights to this manual. Any reproduction or dissemination of any part of this manual in any form without permission is prohibited. Content may be changed without prior notice due to product improvements.

A PDF version of the user manual is available for download: XHORSE Multi-PROG User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.