BAOFENG AR-152 PRO

Contents

Baofeng AR-152 PRO GPS Walkie Talkie User Manual

Model: AR-152 PRO | Brand: BAOFENG

1. Introduction

Welcome to the user manual for your Baofeng AR-152 PRO GPS Walkie Talkie. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before use.

The Baofeng AR-152 PRO is a robust multi-band ham radio featuring GPS, Bluetooth programming, wireless frequency copying, and a high-capacity 12000mAh battery. It is designed for reliable communication in various environments.

Baofeng AR-152 PRO Walkie Talkie highlighting key features like GPS, Bluetooth Programming, Multi Band Frequencies, 12000mAh battery, Wireless Copy, and Fall Down Alarm.
Figure 1: Baofeng AR-152 PRO Walkie Talkie with key features.

2. Safety Regulations and RF Exposure Compliance

It is crucial to adhere to all safety warnings and regulations to ensure safe operation and prevent injury or damage. This radio complies with FCC and EU regulatory standards for RF energy exposure.

2.1 FCC Regulatory Conformance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. It generates and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference. Users are encouraged to correct interference by reorienting the receiving antenna, increasing separation between equipment and receiver, or consulting a technician.

2.2 EU Regulatory Conformance

The product complies with essential requirements and relevant provisions of Directive 2014/53/EU. It can operate under 2000m. This information is applicable to EU countries only.

2.3 RF Exposure Compliance and Control

To control exposure and ensure compliance with environmental exposure limits, observe the following:

  • Do not remove the RF Exposure Label.
  • User awareness instructions should accompany the device.
  • Do not use if operational requirements are not met.
  • Transmit no more than 50% of the time.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, use an approved holder, holster, case, or body harness.

2.4 Precautions for Portable Terminals

Operating Prohibitions:

  • Do not operate in locations with fuels, chemicals, or explosive atmospheres.
  • Do not operate near blasting areas or medical/electronic equipment vulnerable to RF signals.
  • Do not hold while driving.
  • Do not operate where wireless communication is prohibited.

Important Tips:

  • Use only authorized accessories.
  • Keep the product at least 2.5 cm away from your body during transmission.
  • Avoid prolonged high-volume reception.
  • Do not place the product over airbags in vehicles.
  • Keep out of reach of children and pets.
  • Operate within specified temperature range.
  • Allow for cooling during continuous transmission.
  • Handle with care.
  • Do not disassemble, modify, or repair without authorization.

3. Setup and Installation

3.1 Package Contents

Your Baofeng AR-152 PRO package should include:

  • 1 x Transceiver (Radio Unit)
  • 1 x Li-Ion Battery Pack (12000mAh)
  • 1 x Antenna
  • 1 x Adapter (Output DC10V)
  • 1 x User Manual (PDF available for download: User Manual PDF)
  • 1 x Lanyard
  • 1 x Charger
Image showing the Baofeng AR-152 PRO walkie talkie and its accessories: antenna, battery, charger, lanyard, and manual.
Figure 2: Included accessories for the AR-152 PRO.

3.2 Battery Information and Charging

The Li-ion battery pack is not fully charged at the factory. Charge it before first use. Full capacity is reached after 2-3 full charge/discharge cycles.

Charging Prohibitions:

  • Do not charge in explosive atmospheres.
  • Do not charge a wet, deformed, leaking, or overheated battery.
  • Use only the specified charger.
  • Avoid charging in strong radiation areas.
  • Do not overcharge.

How to Charge:

  1. Plug the AC adapter into an AC outlet.
  2. Connect the AC adapter cable to the DC jack on the side of the battery.
  3. Charging takes approximately 2-5 hours. The lamp turns green when charging is complete.

WARNING: If the radio is powered on during charging, the indicator lamp will not turn green to show full charge. Always power off the radio for proper charging indication.

Diagram showing three charging methods for the Baofeng AR-152 PRO: Wall Charger, Car Charger, and USB Charger.
Figure 3: Charging methods for the AR-152 PRO.

LED Indicator Status:

StatusLED
Charge NormallyRed
Fully ChargedGreen

3.3 Installing/Removing the Battery Pack

Ensure the radio is OFF before installing or removing the battery.

Installation:

  1. With the radio back facing you, insert the bottom of the Li-ion battery pack into the bottom of the radio.
  2. Push down the battery pack until the Battery Lock Tab clicks into place.

Removal:

  1. Press the Battery Lock Tab downward.
  2. Pull the Li-ion battery pack away from the radio.

3.4 Installing/Removing the Antenna

Installation: Screw the antenna clockwise into the connector on top of the transceiver until secure.

Removal: Turn the antenna counter-clockwise to remove it.

3.5 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Diagram showing the connection points for an external speaker and microphone to the radio's double jack.
Figure 4: Speaker/Microphone connection diagram.

4. Operating Instructions

This section covers the basic and advanced operations of your Baofeng AR-152 PRO.

4.1 Radio Overview and LCD Icons

Comparison image of AR-152 and AR-152 PRO models, highlighting features like GPS, Bluetooth Programming, Multi Band, Flashlight, 10W power, 12000mAh Battery, and Color screen on the PRO model.
Figure 5: AR-152 PRO features compared to AR-152.

The radio features a 1.77" HD color screen and a full keyboard for easy operation. Key components include:

  • Antenna
  • Flashlight
  • Status LED
  • Sweep/Emergency Alarm button
  • Power/Volume control knob
  • Speaker
  • Microphone
  • LCD Display
  • Battery release latch
  • Broadcast FM and Power switch Key
  • PTT Key
  • Customized keys (defaults to monitor and flashlight)
  • A/B Switch / Exit key
  • MENU/Enter key
  • Numeric keypad

LCD Icon Summary:

IconDescription
████Battery level indicator
DDual watch enabled
VVOX enabled
★Bluetooth writing function activated
☆GNSS function enabled
☇Keypad lock enabled
ZONE01Indication of the current channel's region. Working in storage mode
VFOIn the current working VFO mode. Allow manual frequency input
AA displays (upper section) and emission level indication
BB displays (lower section) and emission level indication
SOLSquelch Open/Close Indicator
HTransmit power level indicator, According to Power High
MThe current transmission power is medium power (used in normal environments).
LTransmit power level indicator, According to Power Low
DDCS enabled
CCTCSS enabled
+Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX.
-Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX
RReverse function enabled
TTalkaround has been activated, off grid at the central turntable. The transmission frequency is equal to the receive frequency
NNarrowband enabled

4.2 Basic Operations

4.2.1 Power On/Off

  • To turn on: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, then a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • To turn off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

4.2.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Use the Monitor function (long press [SK2]) to adjust volume with un-squelched static.

4.2.3 Main Band/Sub Band Switch

In standby mode, press the [EXIT] key to switch between the main and sub frequency bands. The highlighted band is main, dimmed is sub.

4.2.4 VFO/Channel Switch

Press and hold the [MENU] key to switch between VFO (Frequency) mode and Channel (MR) mode.

  • In Channel (MR) mode, zones and channel numbers are displayed.
  • In Frequency (VFO) mode, "VFO" is displayed.

4.2.5 Frequency (VFO) Mode

In VFO mode, use the ▲ or ▼ keys to navigate up and down the band. Frequencies can also be input directly via the numeric keypad (e.g., [4][3][6][6][1][2][5][0] for 436.61250 MHz).

WARNING: Transmitting on unauthorized frequencies is illegal. Always verify your authorization before transmitting.

4.2.6 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use with preprogrammed channels. Frequency (VFO) mode is used for experimentation and programming.

To select a channel:

  • Use the ▲ or ▼ navigation keys.
  • Input channel numbers directly (e.g., [0][1][2] for channel 12).

4.2.7 Making a Call

Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone. The red LED will illuminate.

Frequency Mode Call: Switch to frequency mode (hold [MENU]), input the desired frequency, then hold [PTT] to transmit. The red LED will illuminate.

Receive a Call: Release the [PTT] key. The green LED will illuminate when receiving a call.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

4.2.8 FM Radio (FM)

Listen to FM radio in the 65-108MHz range.

  1. Press [SK1] to turn on/off the radio.
  2. Select frequency with ▲ or ▼ keys, or input directly.
  3. Press [#/Lock] to automatically search for stations.

Note: The radio will automatically switch to A/B receiving signal frequency/channel mode for normal transmitting/receiving if a signal is detected, then return to FM radio mode when the signal disappears.

4.2.9 Monitor Function

In standby, press and hold [SK2] to enter Monitor mode. This allows monitoring weak signals or matched carriers without signaling. Release [SK2] to exit.

4.2.10 Keypad Lock

Press and hold [#/LOCK] for about two seconds to enable/disable the keypad lock. This locks all keys except the three side keys. The radio can also be configured to automatically lock the keypad after ten seconds of inactivity.

4.2.11 Frequency Reversal and Talkaround

Momentarily press [*/SCAN] to reverse transmit and receive frequencies (channel attribute bar displays R). Press again for talkaround mode (channel attribute bar displays T), where transmit frequency equals receive frequency.

4.2.12 TX Repeaters Tone

Press [PTT] + [SK2] to send a 1750Hz repeaters tone, useful for communications through repeaters. This works even with keypad lock enabled.

In standby, press [TK] to activate search mode. The screen will display "SEARCH UHF SEEK...". When a frequency is found, it will display the frequency and any CTCSS/DCS values. Press [MENU] to save to a channel. During search, press [#/LOCK] to switch between UHF or VHF bands.

Instructions for One Touch Search Frequency, showing steps to set SK1 key, press keyboard, search, and save channel.
Figure 6: One Touch Search Frequency instructions.

Video 1: Phone APP Wireless Programming and GPS/Frequency Matching demonstration.

4.3 Advanced Features

4.3.1 Scanner

The radio has a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to the set frequency step. In Channel (MR) mode, it scans your channels.

  • Frequency Ranger: Set precise sweep ranges in frequency mode.
  • Scan Modes: Time Operation (stops, then resumes after timeout), Carrier Operation (stops, then resumes after signal disappears), Search Operation (stops on signal, requires manual resume).
  • Scan Sub-Code: Search for CTCSS/DCS codes.

4.3.2 Dual Watch

Monitor two channels simultaneously. The radio can flip-flop between two frequencies or use two receivers (Dual Receive/Dual VFO). To enable/disable Dual Watch:

  1. Press [MENU] to enter the main menu.
  2. Enter 4 for Radio Settings, then 15 for Dual Watch.
  3. Select ON/OFF and confirm with [MENU].

4.3.3 Manual Programming (Channels Memory)

Store commonly used frequencies in 10 zones, each with up to 100 channels. Each channel can store RX/TX frequencies, transmit power, signaling info, bandwidth, ANI/PTT-ID, and a 6-character alphanumeric identifier.

Example: Programming a Channel Repeater Offset with CTCSS Tone

For detailed steps, refer to page 24 of the user manual (PDF available above).

4.3.4 Bluetooth Write Frequency

Read and write frequencies wirelessly via Bluetooth using an APP. To enable Bluetooth:

  1. Press [MENU] + [3].
  2. Select "ON" using ▲ or ▼ keys. The Bluetooth icon will display.
QR codes for downloading the Bluetooth Programming APP for iOS and Android devices.
Figure 7: Scan QR codes to download the Bluetooth Programming APP.

4.3.5 GPS Function

The built-in GPS module supports multi-mode GPS (GPS, Beidou, or GPS+Beidou) for accurate location tracking, sharing, and requesting location information from others. In GPS mode, you can view location information but cannot make normal calls.

To use GPS:

  1. Turn on GPS in the MENU: [MENU] + 5 + [MENU] + 1, then select ON.
  2. Set Time Zone: [MENU] + 5 + [MENU] + 2, then select your time zone.
  3. Select GPS Mode: [MENU] + 5 + [MENU] + 3, then choose GPS, BDS, or GPS+BDS.
  4. In standby, press and hold [EXIT] to enter GPS mode and display "My Place".
  5. Press [MENU] to switch between information list mode and electronic compass mode.
Two Baofeng AR-152 PRO radios in a desert setting, showing GPS location pins on a map, illustrating the global positioning feature.
Figure 8: Global Positioning feature in action.

4.3.6 Fall Down Function

The radio detects tilt and movement. If conditions (Trig Tilt Gradient, Trig Entry Delay Time) are met, it enters Fall Down mode automatically, triggering an alarm. This feature can be configured for "Tilt Only", "No Movement Only", or "Tilt or No Movement".

  • Trig Tilt Gradient: Sets the tilt degree to trigger Fall Down mode (default 60°).
  • Trig Entry Delay Time: Sets the time period before activating the mandown alarm (default 10 seconds).
  • Fall Down Pre-Alert Time: Sets the duration of the alert tone before entering emergency mode (default 5 seconds).

4.4 Main Menu Functions and Shortcuts

The main menu allows access to various settings including BANKS, SCAN, Bluetooth, GNSS, Radio Settings, Program Channels, Recording, and Radio Information.

Basic Use:

  1. Press [MENU] to enter.
  2. Use ▲ or ▼ to navigate.
  3. Press [MENU] to select an item.
  4. Use ▲ or ▼ to select a parameter.
  5. Press [MENU] to confirm and save.
  6. Press [EXIT] to cancel changes or exit the menu.
  7. Press PTT to exit the menu at any time.

Shortcuts: Many menu items have numerical values for direct access (e.g., [MENU]+1 for zones selection, [MENU]+3 for Bluetooth frequency write, [MENU]+5 for position system settings).

5. Maintenance

5.1 Battery Maintenance Instructions

  • Clean charging connector regularly with a dry cloth.
  • Charge battery between 5℃~40℃ to prevent life reduction or leakage.
  • Turn off the radio when charging a battery attached to the product.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire.
  • Avoid direct sunlight or other heat sources.
  • Do not squeeze, penetrate, or remove the battery housing.

5.2 General Care

  • Use only authorized accessories.
  • Operate within the specified temperature range.
  • Handle the product with care.
  • Do not disassemble, modify, or repair the product without authorization.

6. Troubleshooting Guide

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery improperly installed, power run out, or poor battery contact.Reattach battery, recharge/replace battery, clean contacts.
Weak or intermittent voice during receiving.Low battery voltage, low volume, loose/incorrectly installed antenna, blocked speaker.Recharge battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Frequency/signaling type inconsistent, too far from others.Verify TX/RX frequency/signaling type, move closer.
Hears unknown voices or noise.Interrupted by other radios, analog mode with no signaling.Change frequency, adjust squelch, set signaling.
Unable to hear anyone due to too much noise/hiss.Too far from others, unfavorable position (blocked by buildings), external disturbance.Move closer/to open area, restart radio, avoid interference.
Radio keeps transmitting.VOX turned on, headset not in place.Turn off VOX, check headset.

For further technical support, contact your dealer or refer to the full user manual.

7. Technical Specifications

Image showing the 1.77 inch large screen of the Baofeng AR-152 PRO displaying weather information and NOAA Weather Radio features.
Figure 9: 1.77" Large Screen with NOAA Weather Radio.
General
Channel Capacity1000/10 Bank
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-ion: 15 hours @ 5 watts
Operating temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions222mm X 70mm X42mm (not including antenna)
Radio Weight547 g (with Li-ON battery)
Transmitter
Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
144 to 148 MHz, 430 to 450MHz (Canadian version)
144 to 146 MHz, 430 to 440MHz (European Union version)*
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
Receiver
Frequency RangeFM76-108MHz; AM108-136MHz;
VHF: 136-174 MHz; 220-260MHz; UHF:350-390MHz; 400- 520 MHz;
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

Note: All specifications may be modified without prior notice or liability.

8. User Tips

  • Display: The AR-152 PRO features a clear display for easy viewing of frequencies and settings.
  • Range: Expect a maximum communication range of 5km-10km, which can vary based on terrain and obstacles.
  • Power Output: The radio offers a power output range of 10W-25W, allowing for flexible use depending on your communication needs.
  • Water Resistance: The device is rated IP55 for water and dust resistance, making it suitable for outdoor use in various conditions.
  • Programming: Utilize the Bluetooth Phone Programming feature for convenient wireless setup and channel management via a smartphone app. This simplifies the process compared to traditional cable programming.
  • GPS: Make sure to enable GPS in the menu and set the correct time zone and GPS mode (GPS, BDS, or GPS+BDS) for accurate location services. For best results, use GPS in an open area.
  • NOAA Weather Radio: Keep the NOAA feature active to receive timely weather alerts, which can be crucial in emergency situations.

9. Warranty and Support

For any issues not covered in this manual, or for further technical support, please contact your dealer. You can also refer to the official EU Declaration of Conformity and contact information:

Disclaimer: The manufacturer reserves the right to change the design and specification of the product without notice due to continuous technological development. No part of this handbook may be reproduced or disseminated without prior written authorization.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.