1. Introduction
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of the Estardyn 2.4 inch TFT SPI LCD Module (Model GMT024-08-SPI8P). This display features a 240x320 resolution with 65K colors, driven by the ST7789 IC, and communicates via an 8-pin SPI interface. It is designed for integration into various embedded systems and DIY electronics projects.
2. Specifications
| Feature | Description |
|---|---|
| Model Number | GMT024-08-SPI8P |
| Display Type | TFT LCD |
| Screen Size | 2.4 inch |
| Resolution | 240x320 pixels |
| Color Depth | 65K colors |
| Driver IC | ST7789 |
| Interface | 8-pin SPI |
| Power Supply | 3.3V |
| PCB Dimensions | 46.90mm x 71.00mm |
| Active Area | 37.42mm x 57.60mm |
| Weight | Approximately 0.04 kg |
| Package Dimensions | 7cm x 5cm x 1cm |
For detailed dimensions and pinout, refer to the technical drawing below:

3. Setup and Connection
This section outlines the physical connection of the 2.4 inch TFT SPI LCD module to a microcontroller. Ensure your microcontroller operates at 3.3V logic levels or use appropriate level shifters if necessary.
3.1 Pinout Description
The module features an 8-pin interface. The pin functions are as follows:
| Pin No. | Symbol | Description |
|---|---|---|
| 1 | GND | Ground |
| 2 | VCC | Power Supply (3.3V) |
| 3 | SCL | SPI Clock Line |
| 4 | SDA | SPI Data Line (MOSI) |
| 5 | RST | Reset Pin (Active Low) |
| 6 | DC | Data/Command Selection Pin |
| 7 | CS | Chip Select Pin (Active Low) |
| 8 | BL | Backlight Control (Connect to 3.3V for ON, or PWM for brightness control) |
3.2 Connection Diagram
Connect the display module to your microcontroller according to the pinout. A typical connection to an Arduino-compatible board is shown below. Refer to your microcontroller's documentation for specific SPI pin assignments.


4. Operating Instructions
To operate the display, you will need to use a microcontroller and appropriate software libraries. The ST7789 driver IC is widely supported by various open-source libraries.
4.1 Software Libraries
For Arduino-compatible microcontrollers, popular libraries include:
- Adafruit GFX Library: A core graphics library that provides common drawing functions.
- Adafruit ST7789 Library: A specific driver library for the ST7789 controller, which works in conjunction with the GFX library.
- TFT_eSPI Library: A highly optimized graphics library for ESP32 and ESP8266 microcontrollers, offering excellent performance.
4.2 Basic Initialization and Display
After installing the necessary libraries, you will typically initialize the display by specifying the SPI pins (SCL, SDA, CS, DC, RST) and then calling an initialization function. Basic operations include:
display.init(): Initializes the display.display.setRotation(): Sets the screen orientation.display.fillScreen(color): Fills the entire screen with a specified color.display.setTextSize(size): Sets the size of text.display.setTextColor(color): Sets the color of text.display.setCursor(x, y): Sets the text cursor position.display.print("Hello World"): Prints text to the display.display.drawPixel(x, y, color),display.drawLine(),display.drawRect(), etc.: Drawing primitives.
Refer to the specific library documentation and examples for detailed programming guides.


5. Maintenance
Proper care and maintenance will ensure the longevity and optimal performance of your LCD module.
5.1 Cleaning
- Gently wipe the display surface with a soft, lint-free cloth.
- For stubborn smudges, lightly dampen the cloth with distilled water or a specialized screen cleaner. Avoid harsh chemicals or abrasive materials.
- Do not spray cleaning solutions directly onto the screen.
5.2 Storage and Handling
- Store the module in a dry, dust-free environment, away from direct sunlight and extreme temperatures.
- Avoid applying excessive pressure to the display surface.
- Handle the module by its edges to prevent damage to the display area or electronic components.
- Protect the flexible flat cable (FFC) connector from bending or tearing.
6. Troubleshooting
If you encounter issues with your display module, refer to the following common problems and solutions:
6.1 Blank Screen / No Display
- Check Power: Ensure VCC is connected to 3.3V and GND is properly grounded.
- Check Backlight (BL): Ensure the BL pin is connected to 3.3V to turn on the backlight. If using PWM for brightness control, verify the signal.
- Verify Connections: Double-check all SPI connections (SCL, SDA, RST, DC, CS) for proper wiring and secure contact. Loose connections are a common cause of issues.
- Software Initialization: Confirm that your code correctly initializes the ST7789 driver IC and that the correct pin assignments are used in your library setup.
- Reset Pin: Ensure the RST pin is correctly toggled during initialization.
6.2 Distorted or Incorrect Colors
- Color Inversion: Some displays or libraries might default to inverted colors. Check your library's documentation for a color inversion function (e.g.,
invertDisplay(true/false)) and adjust as needed. - Data Format: Ensure your data is being sent in the correct format (e.g., RGB565 for 16-bit color).
- SPI Speed: While less common, very high SPI speeds might cause data corruption. Try reducing the SPI clock speed in your code.
6.3 Low Brightness
- Backlight Connection: Ensure the BL pin is receiving a stable 3.3V.
- PWM Control: If using PWM for brightness, verify the duty cycle is set to maximum for full brightness.
7. User Tips
- Power Supply: Always ensure a stable 3.3V power supply for the module. Incorrect voltage can damage the display.
- Wide Viewing Angles: This display offers good readability from various angles, making it versatile for different applications.
- Compatibility: The module is generally easy to use with common microcontrollers like Arduino and ESP32, provided the correct libraries and wiring are implemented.
- Color Correction: If colors appear inverted, check your software library for a display inversion command. This is a common setting that can be easily adjusted.
- Physical Integration: When integrating the module into a project, ensure it is securely mounted and protected from physical stress. Some users have successfully integrated it into existing devices after minor modifications.
8. Warranty and Support
For technical support, warranty claims, or any questions regarding the Estardyn 2.4 inch TFT SPI LCD Module, please contact your retailer or the manufacturer directly. Provide your model number (GMT024-08-SPI8P) and a detailed description of the issue to facilitate assistance.