HWATEL 900-1800 B8 B3 Dual Band Cellular Signal Booster

Contents

HWATEL Dual Band 900/1800MHz Cellular Signal Booster

Model: 900-1800 B8 B3 Dual Band Cellular Signal Booster

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your HWATEL Dual Band 900/1800MHz Cellular Signal Booster. This device is designed to enhance 2G, 3G, 4G LTE, and 5G cellular signals in areas with weak coverage, specifically supporting 900MHz (Band 8) and 1800MHz (Band 3) frequencies, commonly used in Europe and other regions.

The booster features an intelligent LCD display for monitoring signal levels and incorporates Auto Level Control (ALC) technology for optimized performance and extended service life.

2. Package Contents

Please verify that all items listed below are included in your package:

  • 1 x Signal Booster (with AC/DC Adaptor)
  • 1 x Outdoor LOG Antenna
  • 1 x Indoor ROD Antenna (with 2-meter cable)
  • 1 x 10-meter Coaxial Cable
Contents of the HWATEL signal booster package, including booster, power adapter, LOG antenna, 10-meter cable, and ROD indoor antenna with 2-meter cable.
Figure 2.1: Package Contents

3. Specifications

FeatureDescription
Frequency Bands900MHz (Band 8) for 2G/3G, 1800MHz (Band 3) for 4G LTE
Gain74 ± 5 dB
Output Power20 dBm
Coverage AreaUp to 500 square meters (actual coverage depends on outdoor signal strength and building structure)
FeaturesAuto Level Control (ALC), Intelligent LCD Display, Qualcomm Core Chip
CertificationsCE, FCC, RoHS
OriginMainland China
Booster Dimensions104mm x 84mm x 20mm
Outdoor LOG Antenna600-4000MHz, 9-12dB gain, N Female connector, 29/34cm height
Indoor ROD Antenna700-5300MHz, 7-15dB gain, 360° Omnidirectional, RG-174 RF cable (2 meters), N Male connector
Coaxial CableHWATEL-3D-FB, Double Shield, 698-3500MHz, N Male to N Male connectors
Dimensions of the HWATEL signal booster: 104mm length, 84mm width, 20mm thickness.
Figure 3.1: Booster Dimensions
Specifications of the LOG Antenna: 600-4000MHz, 9-12dB gain, 5G 4G 3G 2G Wifi compatible, 29/34cm height, N Female connector.
Figure 3.2: LOG Antenna Specifications
Specifications of the ROD Indoor Antenna: ABS Polymer Housing, 360-degree Omnidirectional, 700-5300MHz, 4G 5G Wifi Compatible, RG-174 RF cable 2 Meter, Easy Install Base.
Figure 3.3: ROD Indoor Antenna Specifications
Diagram of HWATEL-3D-FB Low Loss Cable, showing Double Shield, 698-3500MHz, Dualable PVC, Double High Density Shielding, Copper Core, Phisically Foamed PE, and N Male to N Male connectors.
Figure 3.4: Low Loss Cable Specifications

4. Setup and Installation

Proper installation is crucial for optimal performance. Follow these steps carefully:

4.1. Site Selection

  • Outdoor Antenna Placement: Choose a location outdoors, preferably on the roof or a high point, where you receive the strongest and most stable cellular signal from your service provider. The LOG antenna is directional, so point it towards the nearest cell tower.
  • Indoor Antenna Placement: Place the ROD indoor antenna in the center of the area where you need improved signal. Ensure there is sufficient physical separation (at least 10-15 meters, or through walls/floors) between the outdoor and indoor antennas to prevent signal oscillation.
  • Booster Placement: Install the booster in a dry, well-ventilated area, away from direct sunlight and heat sources.

4.2. Connection Steps

  1. Mount Outdoor Antenna: Securely mount the LOG outdoor antenna using the provided mounting hardware. Point it towards the strongest signal source.
  2. Connect Outdoor Cable: Connect one end of the 10-meter coaxial cable to the outdoor antenna. Run the cable to the location of the booster.
  3. Connect to Booster (BTS Port): Connect the other end of the 10-meter coaxial cable to the 'BTS' port (Outdoor Antenna port) on the signal booster.
  4. Mount Indoor Antenna: Place the ROD indoor antenna in your desired coverage area.
  5. Connect to Booster (MS Port): Connect the 2-meter cable from the indoor antenna to the 'MS' port (Indoor Antenna port) on the signal booster.
  6. Power On: Connect the AC/DC power adapter to the booster's power input, then plug it into a power outlet. The booster will power on, and the LCD display will activate.
Diagram of the signal booster showing the 'BTS' port for the Outdoor Antenna and 'MS' port for the Indoor Antenna, along with the Intelligent LCD Display for Source Signal Level.
Figure 4.1: Booster Port Connections and LCD Display

Important: Ensure all connections are tight and secure before powering on the device. Do not power on the booster without both antennas connected and properly separated.

5. Operating Instructions

Once installed and powered on, the HWATEL signal booster operates automatically.

  • LCD Display: The intelligent LCD display on the booster shows the 'Source Signal Level'. Monitor this display to ensure the outdoor antenna is receiving a strong signal. A higher signal level indicates better performance.
  • Auto Level Control (ALC): The booster is equipped with ALC, which automatically adjusts the gain to prevent interference with the cellular network and optimize signal quality. This feature also contributes to the longevity of the device.
  • Signal Enhancement: The booster will amplify the 900MHz and 1800MHz signals and re-broadcast them via the indoor antenna, providing improved call quality and data speeds within the coverage area.
Comparison showing HWATEL Booster with ALC providing high gain and power, accurate frequency, and clear wave, versus other brands without ALC having lower performance.
Figure 5.1: Auto Level Control (ALC) Benefit

6. Maintenance

The HWATEL signal booster requires minimal maintenance to ensure long-term performance:

  • Keep Clean: Periodically wipe the booster unit with a soft, dry cloth to remove dust.
  • Check Connections: Occasionally inspect all cable connections (outdoor antenna to booster, indoor antenna to booster) to ensure they remain tight and free from corrosion.
  • Environmental Conditions: Ensure the booster is kept within its specified operating temperature and humidity ranges. Avoid exposing it to extreme weather conditions or moisture.
  • Antenna Inspection: Periodically check the outdoor antenna for any physical damage or obstructions (e.g., tree branches, debris) that might affect signal reception.

7. Troubleshooting

If you experience issues with your signal booster, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No signal improvement / Weak signal
  • Outdoor antenna not receiving strong enough signal.
  • Insufficient separation between outdoor and indoor antennas (oscillation).
  • Loose or damaged cable connections.
  • Incorrect antenna direction.
  • Booster not powered on.
  • Adjust outdoor antenna direction or relocate to a stronger signal area.
  • Increase physical separation between outdoor and indoor antennas.
  • Check and tighten all cable connections. Replace damaged cables.
  • Ensure outdoor antenna is pointed towards the nearest cell tower.
  • Verify power adapter is connected and booster is on.
LCD display shows low signal levelOutdoor antenna is not picking up a strong signal.Adjust the position or direction of the outdoor antenna until a higher signal level is displayed.
Booster is hot to the touchPoor ventilation or excessive load.Ensure the booster is in a well-ventilated area. If the problem persists, contact support.

8. User Tips

  • Frequency Compatibility: Before purchasing or installing, always verify that the booster's supported frequencies (900MHz Band 8 and 1800MHz Band 3) are compatible with your local mobile network operator. Some regions or carriers may use different bands (e.g., 700MHz for Orange in France, as noted in Q&A), which this specific booster does not support.
  • Antenna Separation: The most common cause of poor performance is insufficient separation between the outdoor and indoor antennas. Aim for maximum possible separation, both horizontally and vertically, to prevent feedback and ensure efficient operation.
  • Outdoor Signal Strength: The booster amplifies an existing signal. If there is absolutely no signal outdoors, the booster will have nothing to amplify. Ensure you have at least a weak, usable signal outdoors for the booster to work effectively.
Image showing various telecom carrier logos and the text 'HWATEL Booster Support ALL Telecom Carriers! Make Sure you choose CORRECT Frequency.'
Figure 8.1: Ensure Frequency Compatibility with Your Carrier

9. Warranty and Support

HWATEL products are manufactured to high-quality standards. For specific warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support or further assistance, please reach out to the HWATEL customer service team through your purchase platform.

© 2023 HWATEL. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.