Baofeng BF-C5/BF-C2/BF-V9

Contents

Baofeng BF-C5/BF-C2/BF-V9 Walkie Talkie Instruction Manual

Models: BF-C5, BF-C2, BF-V9

1. Introduction

This manual provides detailed instructions for the safe and efficient operation of your Baofeng BF-C5, BF-C2, or BF-V9 walkie talkie. Please read this manual thoroughly before using the device.

Baofeng BF-C5 Walkie Talkie with key features listed: 1500mAh Battery, UHF 400-470MHz, Type-C Charging, 5W.
Baofeng BF-C5 Walkie Talkie highlighting its 1500mAh battery, UHF 400-470MHz frequency, Type-C charging, and 5W power output.

2. Package Contents

The standard package includes the following items:

  • Radio Body (1x / 2x / 4x, depending on variant)
  • Battery Pack (1x / 2x / 4x)
  • Antenna (1x / 2x / 4x)
  • Belt Clip (1x / 2x / 4x)
  • English Manual (1x / 2x / 4x)
  • Charger (USB/US/EU, 1x / 2x / 4x)
  • Hand Strap (1x / 2x / 4x)
Image showing the standard package contents for the Baofeng walkie talkie, including the radio, battery, charger, antenna, belt clip, hand strap, and manual.
Standard package contents for the Baofeng walkie talkie.

3. Product Overview

Familiarize yourself with the components of your walkie talkie:

Diagram of the walkie talkie with labeled parts A through J.
Radio outlook with labeled components.
  1. LED Indicator: Green LED flashes when receiving a signal, Red LED flashes when transmitting.
  2. Channel Knob: Rotate to select channels (CH1-CH15). CH16 is the scan channel.
  3. ON/OFF Knob/Volume Knob: Rotate clockwise to turn on the radio, counter-clockwise to turn off. Controls volume.
  4. PTT Switch: Press and hold to transmit, release to listen.
  5. Monitor: Press to open squelch and hear background noise; release to close squelch.
  6. USB Rapid Charge Plug.
  7. Speaker/Microphone Rubber Plug: Cover when not using speaker and microphone.
  8. Insert Loudspeaker.
  9. Microphone.

4. Setup

4.1 Battery Charging

Your walkie talkie is powered by a 1500mAh Li-ion battery. Follow these steps to charge it:

  1. Take out the charger and plug it into an AC (100-240V) 50/60Hz power outlet. The green LED on the charger will flash.
  2. Plug the battery or the radio with the battery attached into the charger. Ensure the battery is properly connected.
  3. The charging process begins when the red LED lights up. The charging time depends on the battery capacity.
  4. The green LED lights up when the battery is fully charged.
  5. Alternatively, use the USB cable to plug directly into the radio. The red LED indicates charging, and the green LED indicates a full charge.
Image of a 1500mAh Li-ion battery for the walkie talkie, showing its model BL-V2 and warning labels.
1500mAh Li-ion Battery (Model: BL-V2).
Diagram illustrating USB fast charging options for the walkie talkie, including connection to a notebook computer, power bank, and car charger.
USB Type-C Fast Charging options.

5. Operation

5.1 Switching Power ON/OFF

Turn the power switch/volume control (C) clockwise. You will hear a channel number, indicating the radio is ON.

5.2 Adjusting the Volume

Hold the MONI button (E) down to listen to the audio level while rotating the Power switch/Volume control (C). Rotate clockwise to increase volume and counter-clockwise to decrease volume.

5.3 Selecting the Channel

Turn the channel switch (B) to select your desired channel. Channel 16 is designated as the Scanning Channel.

5.4 PTT Transmit

To transmit, press and hold the PTT switch (D) and speak into the microphone in your normal tone of voice. Release the PTT switch to listen.

5.5 Squelch Level

The squelch function mutes the speaker when no signals are present. With the squelch level correctly set, you will only hear sound when actually receiving signals. The squelch level can be adjusted via program software. The frequency of squelch ranges from 0 (on) to 9 (deep), in steps of 1.

5.6 Scanning Switch

If the walkie-talkie is set for scanning via software, turn the channel selector to channel 16. The radio will automatically detect activity on channels CH1 to CH15. When a signal is detected, the radio will stop on that channel for the call.

  • The walkie-talkie will stay on the signal channel. If the signal disappears, it will continue scanning after 15 seconds.
  • Scanning requires at least 2 channels to be set.
  • On channel 16, pressing and holding the PTT and MONI keys will toggle SCAN on or off.
  • Scanning is not possible if the FM radio function is active.

5.7 VOX Function

VOX (Voice Operated Transmit) allows for hands-free transmission. When the sound level is higher than the set VOX gain level, the radio automatically transmits. The VOX gain level can be adjusted from 1 to 9 levels. Note that VOX will not transmit if a signal is being received, even if your sound level is higher than the VOX gain level.

To activate/deactivate VOX on channels CH1-CH5, press and hold the PTT and MONI buttons while switching on the radio.

5.8 Battery Saving

When enabled, the radio automatically enters a battery-saving state after 10 seconds of inactivity. This function can be turned ON or OFF.

5.9 Busy Channel Lockout (BCL)

BCL prevents transmission on a channel that is currently in use. This feature can be enabled or disabled via PC programming software.

5.10 Beep Function

When the beep function is on, a 'Di' sound is emitted with every rotation of the channel knob. This function can be turned off.

5.11 Low Battery Voltage Warning

When the battery voltage drops below a preset value, a

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.