BAOFENG UV18 Pro Max

Contents

Baofeng UV18 Pro Max GPS Walkie Talkie User Manual

Model: UV18 Pro Max

1. Getting Started

1.1 Regulations and Safety Warnings

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

WARNING! MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:

  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions should accompany device when transferred to other users.
  • Do not use this device if the operational requirements described herein are not met.
  • Transmit no more than the rated duty factor of 50% of the time.
  • Keep the radio unit at least 2.5cm away from the face.
  • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
  • Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
  • Contact your local dealer for the product's optional accessories.

1.2 Content of the Packaging

This transceiver comes shipped with the following items in the box:

  • 1 Radio body (UV18 Pro Max)
  • 1 Lithium-Ion battery pack
  • 1 Instruction Manual (User Manual)
  • 1 Belt Clip
  • 1 Desk charger (With wall-wart)
  • 1 Antenna
  • 1 Wrist Belt
  • 1 USB-C Charger

*If any item is missing, please notify your Baofeng / Pofung dealer.

Diagram showing all components included in the UV18 Pro Max standard package: radio, battery, antenna, belt clip, USB-C charger, desktop charger, user manual, and box.
Figure 1: Standard Package Contents

2. Battery Information

2.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. Charging for the first time or after extended storage (more than 2 months) may require 2-3 full charge/discharge cycles to reach optimal capacity. Use only the specified charger provided by Baofeng.

Charging Prohibitions:

  • Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres.
  • Do not charge a wet battery; dry it with a clean cloth first.
  • Do not charge a battery suffering deformation, leakage, or overheat.
  • Do not charge with an unauthorized charger.
  • Do not charge in a location with strong radiation.
  • Overcharging may shorten battery life.

How to Charge:

  1. Plug the AC adaptor into an outlet and connect it to the charger. The indicator light blinks orange.
  2. Plug the battery or the radio into the charger. The indicator light turns red, indicating charging has begun.
  3. Full charge takes approximately 2-5 hours. The lamp lights green when charging is complete.

NOTICE: When charging the radio with the battery installed and powered on, the indicator may not turn green. For accurate indication, turn off the radio during charging.

LED Indicator Status
Red LED Green LED Status
Flashing Steady Standby (charger empty) / Error (charger with radio)
Steady Off Charging
Off Steady Charge complete.

2.2 Battery Maintenance

  • Use only batteries approved by the original manufacturer.
  • Never attempt to disassemble your battery pack.
  • Do not expose your batteries to fire or intense heat.
  • Dispose of batteries in accordance with local recycling regulations.

2.3 Prolonging Battery Life

  • Only charge batteries in normal room temperatures (5°C~40°C).
  • Turn the radio off for faster charging when attached.
  • Do not unplug power or remove battery before charging is complete.
  • Never charge a wet battery.
  • Replace battery if operating time significantly shortens.

2.4 How to Store the Battery

  • Store at 80% discharged.
  • Keep in low temperature and dry environment.
  • Keep away from hot places and direct sunlight.
  • Cycle the battery every six months during long-term storage to prevent severe capacity degradation.

3. Preparation

3.1 Installing / Removing the Battery

Installing:

  1. Position the battery pack over the back of the radio.
  2. Engage the battery pack into the radio until fully seated.
  3. Tighten the screws using a coin or object to secure. Do not overtighten.

Removing:

  1. Loosen the screws on the back of the battery pack.
  2. Lift the bottom of the battery pack slightly.
  3. Pull the battery pack out.

3.2 Installing / Removing the Antenna

Installing:

Screw the antenna into the connector on top of the transceiver clockwise until secure.

Removing:

Turn the antenna counter-clockwise to remove it.

Illustration of the UV18 Pro Max with a high gain antenna, showing radio waves emanating from it.
Figure 2: High Gain Antenna

3.3 Installing / Removing the Belt Clip

Installing:

Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.

Removing:

Unscrew counter-clockwise to remove the belt clip.

3.4 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

4. Radio Overview

Diagram of the UV18 Pro Max radio with numbered parts: 1. Antenna, 2. Flashlight/Emergency Alert key, 3. PTT key, 4. SK2 key, 5. MENU key, 6. Numeric keypad, 7. Power/Volume knob, 8. Color LCD, 9. Speaker/Mic Jacks, 10. MIC Input, 11. Exit Key, 12. Up/Down navigation keys, 13. Battery pack, 14. Type-C charging port, 15. Battery tightening screw, 16. Type-C charging indicator, 17. LED flashlight, 18. LED Status Indicator.
Figure 3: UV18 Pro Max Parts Diagram

4.1 Status Indications

The top LED helps identify the current radio status:

  • Constant Green: Receiving Signal
  • Constant Red: Transmitting Signal
  • Flashes Green: Monitor mode/Scanning Receiving

4.2 LCD Icon Summary

Icon Description
RSSIOperating band signal
HTransmit power level indicator, According to Power High
LTransmit power level indicator, According to Power Low
♪DTMF side tone (DT-ST, ANI-ST, DT+ANI)
DDCS enabled
CCTCSS enabled
+TX shifted higher in frequency than RX (VFO/Frequency Mode)
-TX shifted lower in frequency than RX (VFO/Frequency Mode)
DDual watch enabled
🔒Keypad lock enabled
VOXVOX enabled
NNarrowband enabled
🔋Battery level indicator

4.3 Main Keypad Controls

  • MENU Key: Activates the MENU, selects items, and confirms parameters.
  • Up/Down Keys: Navigate menus, adjust frequency/channel, change scan direction.
  • EXIT Key: Exits menus and functions.
  • Numeric Keypad: Input information, selections, and send DTMF codes.
  • *Key: Enables reverse function, activates/deactivates keypad lock (hold for 2 seconds).
  • # Key: Starts FM scanning (momentary press), enables/disables scanner (hold for 2 seconds), quickly enters DTMF dialing.

5. Basic Operations

5.1 Power On/Off and Volume Adjustment

  • Power On: Rotate the Volume/Power knob clockwise until a "click" is heard.
  • Power Off: Rotate the Volume/Power knob counter-clockwise until a "click" is heard.
  • Adjust Volume: Rotate the Volume/Power knob clockwise to increase, counter-clockwise to decrease.

5.2 Main Band/Sub Band Switch

In standby mode, press the MENU key to switch between the main frequency band or sub frequency bands. The highlighted band is main, dimmed is sub.

5.3 VFO/Channel Switch

Press and hold the MENU key to switch between VFO (Frequency) and Channel (MR) modes.

  • In Channel (MR) mode, the channel number is displayed.
  • In Frequency (VFO) mode, 'VFO' is displayed.

5.4 Frequency (VFO) Mode

Navigate up/down the band using the Up/Down keys or input frequencies directly via the numeric keypad (e.g., [4][3][6][6][1][2][5][0] for 436.61250 MHz).

WARNING! Transmitting on unauthorized frequencies is illegal. Always check local regulations.

5.5 Channel (MR) Mode and Channel Selection

Channel (MR) mode is generally more practical for everyday use. Navigate channels using Up/Down keys or input channel numbers directly.

5.6 Selecting a Bank

The radio supports up to 10 banks, each with a maximum of 100 channels. Press MENU, navigate to 'Bank', select with Up/Down keys, and press MENU again to confirm.

5.7 Making a Call

  • Channel Mode Call: Select a channel, hold PTT key, and speak. Red LED indicates transmission.
  • Frequency Mode Call: Press and hold MENU to switch to frequency mode, input frequency, hold PTT key, and speak. Red LED indicates transmission.
  • Receive a Call: Release the PTT key to receive. Green LED indicates reception.

5.8 Using the Flashlight

Press the Flashlight/Emergency Alert key once for continuous light, press again for strobe, press a third time to turn off.

5.9 Emergency Alert

To activate, press and hold the Flashlight/Emergency Alert key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press the key again to exit.

WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.

5.10 FM Radio (FM)

The SK2 key is defined as the FM radio on/off. Frequency range: 65-108MHz.

  1. In frequency or channel mode, press SK2 to turn on the radio.
  2. Select desired frequency with Up/Down keys or input directly.
  3. Press # to automatically search for a station.
  4. Press SK2 to exit FM radio.

5.11 NOAA Weather Radio/Scan Weather Channel

The radio has NOAA Weather Radio and Scan functions for receiving weather reports.

  1. To turn NOAA Weather Scan on, press and hold the 0 key for 3 seconds.
  2. Press and hold the #2 key for 3 seconds to start automatic scanning of all 10 NOAA channels.
  3. After stopping scan, manually select channels with Up/Down keys.
  4. To exit, press the EXIT key or PTT key.
Weather Channel Frequencies
Channel Number RX Frequency MHz Channel Number RX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

Define SK2 key as Search function via CPS software or Radio Menu > Radio Setting. Briefly press SK2 to initiate search. During search, press # to switch between UHF/VHF bands.

6. Advanced Features

6.1 Scanner

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps; in Channel (MR) mode, it scans your channels. To enable, press and hold #2 for about two seconds. Change scanning direction with Up/Down keys. Press and hold #2 to exit.

6.1.1 Frequency Ranger

In frequency mode, set the sweep range by inputting start and end values (e.g., 144146 for 144.000-146.000MHz). See Menu > SCAN > Freq Ranger.

6.1.2 Scan Modes

  • Time Operation (TO): Scanner stops on signal, resumes after preset timeout.
  • Carrier Operation (CO): Scanner stops on signal, resumes after preset time with no signal.
  • Search Operation (SE): Scanner stops on signal, requires pressing #2 to resume.

6.1.3 Scan Sub-Code (CTCSS/DCS)

To search for a CTCSS code:

  1. In VFO mode, enter a known frequency.
  2. Press MENU > Scan > 3 Scan Sub-Code.
  3. Select CTCSS with Up/Down.
  4. Press MENU to scan CTCSS codes.
  5. Press MENU to store the scanned code and exit.

To search for a DCS code, follow similar steps, selecting DCS instead of CTCSS.

6.1.4 Sub-Code Scan Storage

Scanned CTCSS/DCS codes can be stored as TX, RX, or both. Press MENU > SCAN > 4 Scan Memory, then select ALL, DECODER (RX only), or ENCODER (TX only).

6.2 DTMF (Dual-Tone Multi-Frequency)

DTMF is used for automation systems and remote control, common in amateur radio repeaters. The radio supports full DTMF implementation, including A, B, C, D codes.

DTMF Frequencies and Codes
1209Hz 1336Hz 1477Hz 1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

6.2.1 Call With Signaling

A call with signaling uses preset signaling codes (DTMF) for encoding and decoding. Configure signaling code, mute mode, and PTT-ID via CPS Programming Path >> Programming >> DTMF System.

6.2.2 DTMF Manual Dial

Short press # key to enter DTMF manual dialing. Enter the DTMF number and hold PTT to make a call.

  • Private call: Confirm ID with #, then hold PTT.
  • Group call: Confirm ID with MENU, then hold PTT.
  • All call: Enter #, then hold PTT.

6.3 Dual Watch

The radio features Dual Watch functionality, allowing monitoring of two channels. To enable/disable, press MENU, enter 14 for Dual Watch, then use Up/Down keys to select ON/OFF.

6.4 Manual Programming (Channels Memory)

Memory channels store frequently used frequencies. The radio has 999 memory channels, storing RX/TX frequencies, power, signaling, bandwidth, ANI/PTT-ID, and a 6-character alphanumeric identifier.

Frequency Mode vs. Channel Mode:

  • Frequency Mode (VFO): For temporary frequency assignments.
  • Channel Mode (MR): For selecting preprogrammed channels.

Programming a Channel Repeater Offset with CTCSS Tone:

  1. Press MENU to switch menus.
  2. Press and hold MENU to set radio to VFO mode.
  3. Input [4][1][7] for channel 10.
  4. Input [4][5] for TX encode tone 123.0.
  5. Input [4][1][4] for OFFSET frequency 5.00MHz.
  6. Input [4][1][5] for positive offset.
  7. Enter RX frequency (e.g., 43255000).
  8. Enter the same channel (e.g., 10).
  9. Press and hold MENU to return to MR mode.

Programming a Simplex Channel with CTCSS Tone:

Follow similar steps as above, but for a simplex channel (no offset).

6.5 Repeaters Programming

To program repeater settings:

  1. Press and hold MENU to set to VFO mode.
  2. Enter repeater's output (receive) frequency.
  3. Press [4][1][4] to get offset frequency.
  4. Enter specified frequency offset.
  5. Press MENU to confirm and save.
  6. Press [4][1][5] to get offset direction.
  7. Use Up/Down keys to select plus (+) or minus (-) offset.
  8. Press MENU to confirm and save.
  9. (Optional) Save to memory or set up CTCSS.
  10. Press EXIT to exit.

NOTE: If experiencing problems, check settings or contact your dealer. Some Amateur Radio repeaters use a 1750Hz tone burst.

6.6 Amateur Radio Setup

For typical Amateur radio setup, the following settings are recommended:

  • Turn ANI, DTMFST, PTT-ID off and PTT-LT to 0ms (menu items 18-20).
  • Turn off Squelch Tail Elimination (Tail) features (menu item 23).
  • Turn Roger Beep (ROGER) off (menu item 10).
  • Set bandwidth to Wide (menu item 5).
  • Turn DCS and CTCSS off (menu items 6-9).
  • Turn Signaling code off and SPK-Mute (menu items 11 and 13).

8. Technical Specifications

General
Channel Capacity1000
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 15 hours @ 5 watts
Current Drain (Stand-by)45 mA
Current Drain (Receive)200 mA
Current Drain (Transmit)≤1.6 A @ High Power, ≤1.2 A @ Low Power
Operating temperature-10°C to 60°C
Antenna Impedance50Ω
Dimensions132x56x35mm (no include antenna)
Transmitter
Frequency Range (TX)136 to 174 MHz, 220 to 260 MHz, 400 to 480 MHz
RF Output Power2 or 5 Watts Max (10W)
Modulation16KOF3E/11KOF3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
Receiver
Frequency Range136 to 174 MHz, 220 to 260 MHz, 400 to 520 MHz, FM 65-108MHz, AM 108-136MHz, Police 350-390MHz
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output1.0 Watts @ 16 Ω
Rated Audio Distortion≤5%

NOTE: All specifications may be modified without prior notice or liability.

9. Troubleshooting Guide

Phenomena Analysis Solution
Cannot turn on the radio. Battery improperly installed, battery power low, or dirty contacts. Reattach/recharge/replace battery, clean contacts.
Weak or intermittent voice during reception. Battery voltage low, volume low, loose antenna, or blocked speaker. Recharge battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members. Inconsistent frequency/signaling type, too far away, or interference. Verify TX/RX frequency/signaling, move closer, change frequency/squelch level.
Hears unknown voices or noise. Too far away, interrupted by other radios, or analog mode without signaling. Move closer, change frequency/squelch level, set signaling.
Unable to hear anyone due to too much noise/hiss. Too far away, unfavorable position (blocked), or external disturbance. Move to open area, restart radio, avoid interference.
Radio keeps transmitting. VOX enabled or headset not installed correctly. Turn off VOX, check headphones.

NOTE: If these solutions do not resolve your problems, please contact your dealer for technical support.

10. User Tips

  • For optimal performance, ensure your antenna is securely attached before operation.
  • When using the wireless frequency copy feature, keep the two radios at least 30cm apart for accurate copying.
  • Regularly check battery contacts for cleanliness to ensure reliable charging and power.
  • Familiarize yourself with the keypad lock function to prevent accidental changes to settings during use.
  • Utilize the VOX function for hands-free communication, especially in situations where holding the PTT button is inconvenient.

11. Support and Warranty

For further assistance or technical support, please refer to the official user manual PDF: User manual (PDF).

Fujian Baofeng Electronics Co.,Ltd.
ADD: Changfu Industrial Bank Xiamei, Nan'an, Quanzhou, Fujian, China
E-mail: wangjianhui@baofengradio.com
Website: http://www.baofengradio.com

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for the possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation and dissemination of this handbook may be made in any form without the prior written authorization of our department.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.