BAOFENG UV-21 Pro V2

Contents

BAOFENG UV-21 Pro V2 Wireless Copy Frequency Type-C Walkie Talkie User Manual

Model: UV-21 Pro V2

Brand: BAOFENG

1. Introduction and Safety Information

Thank you for purchasing the BAOFENG UV-21 Pro V2. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation.

1.1 Regulations and Safety Warnings

WARNING!

European Users: Operation of this unit in Transmit mode requires a valid Amateur Radio License from your respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.

ATTENTION!

When programming the radio, first read the factory software data, then rewrite this data with your frequency, etc., to a new saved code plug to avoid errors. Use the programming cable with a PC to program authorized frequencies, bandwidth, power, etc. Your programming must comply with your FCC (or EU/other country) license certification.

ATTENTION!

Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio, which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

FCC Part 15 Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

IC Compliance

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

1.2 Precautions for Portable Terminals

To protect against property loss, bodily injury, or death, observe the following safety instructions:

  1. Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials. Only approved Ex-protection models are allowed, and any attempt to assemble or disassemble is strictly prohibited.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where wireless communication equipment is completely prohibited.

1.3 Precautions for Batteries

Charging Prohibitions

  1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, and other flammable or explosive materials.
  2. Do not charge your battery if it is wet. Dry it with a soft and clean cloth prior to charging.
  3. Do not charge your battery if it is deformed, leaking, or overheating.
  4. Do not charge your battery with an unauthorized charger.
  5. Do not charge your battery in a location where strong radiation is present.
  6. Overcharge is prohibited as it may shorten battery life.

Battery Maintenance Instructions

  1. Accumulated dust on the charging connector may affect normal charging. Clean it regularly with a dry cloth.
  2. Charge the battery between 5°C~40°C. Violating this limit may reduce battery life or cause leakage.
  3. To charge a battery attached to the product, turn it off for a full charge.
  4. Do not remove the battery or unplug the power cord during charging.
  5. Do not dispose of the battery in fire.
  6. Do not expose the battery to direct sunlight for a long time or place it close to other heating sources.
  7. Do not squeeze, penetrate, or remove the housing of the battery.

1.4 General Maintenance

Your Two-Way Radio is a precision electronic product and should be handled with care.

  • Do not attempt to open the radio for any reason. Unauthorized opening voids the warranty.
  • Do not store the radio in direct sunlight or hot areas.
  • Avoid dusty and dirty areas.
  • Keep the radio dry; rainwater or dampness will corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off power and remove the charger or battery.
  • Do not transmit without an antenna.

2. Main Features

  • Tri-Band Frequency: 68-108MHz (FM RX), 136-174MHz (TX&RX), 220-260MHz (TX&RX), 400-480MHz (TX&RX), AM108-136MHz (RX), Police350-390MHz (RX).
  • Wireless Copy Frequency: Easy pairing and grouping by copying channel configuration parameters.
  • Frequency Step: Selectable between 2.5K, 5.0K, 6.25K, 10.0K, 12.5K, 20.0K, 25.0K, 50.0K.
  • Privacy Functions: Frequency hopping and scramble functions to keep calls confidential.
  • Display: 1.77" TFT large screen, full keyboard, fully open menu operation.
  • Channels: Up to 999 memory channels.
  • Scanning: Channel scan, frequency scan, and three scan and recovery methods (TO, CO, SE).
  • Power-on Password: Management function.
  • DTMF: Encoder and manual dial.
  • VOX: Voice Activated Transmit.
  • Alarm Function: Emergency alert.
  • Power Selection: High or low power selectable.
  • Repeater Offset: Programmable.
  • Transmission Time-Out Timer (TOT).
  • LED Flashlight: Built-in for convenience.
  • Roger Beep: End of transmission tone.
  • FM Radio: Broadcast receiver 65-108 MHz.
  • Dual Watch: Dual reception/Dual-band handheld transceiver.
  • Battery: High Capacity Lithium-Ion battery.
  • Stopwatch Function.
  • Display Illumination: Programmable via keypad.
  • Keypad Beep: Function beep on the keyboard.
  • Battery Save Function.
  • Busy Channel Lock Out.
  • Squelch Adjustment: Ten (10) levels.
  • Accessory Port: Two (2) pins for Kenwood accessory port.
  • NOAA Weather: Support NOAA weather reception function in the United States and Canada.

Video: Overview of BAOFENG UV-21 Pro V2 features, including upgrade from UV-5R, multiple functions, 2-second copy frequency, 1.77" color display, two charging methods, flashlight, and NOAA weather channel.

3. Package Contents

The BAOFENG UV-21 Pro V2 package typically includes the following items:

  • 1 x Portable Radio (UV-21 Pro V2)
  • 1 x Antenna
  • 1 x Li-ion Battery Pack
  • 1 x Type-C USB Charger (cable)
  • 1 x Base Charger (desktop charger)
  • 1 x Belt Clip
  • 1 x Lanyard (The Sling)
  • 1 x User's Manual (BF-21 SERIES)
  • 1 x Screwdriver (often included as a gift)
BAOFENG UV-21 Pro V2 package contents and specifications

Image: Visual representation of the BAOFENG UV-21 Pro V2 package contents, including the radio, antenna, battery, base charger, Type-C cable, clip, lanyard, and user manual. Also lists key specifications.

4. Radio Overview

4.1 Buttons and Controls of the Radio

Diagram of BAOFENG UV-21 Pro V2 with labeled parts

Image: Front, left, and right side views of the BAOFENG UV-21 Pro V2 walkie talkie, with labels for the Antenna, Flashlight, Power/Volume Switch, PTT Key, Emergency Alert Key, FM/Monitor Key, Speaker, MENU Key, VFO/MR Key, A/B Key, Navigation Keys, NXIT Key, and Headset Jack.

  1. Antenna
  2. PTT key
  3. SK1-FM broadcast/Monitor key
  4. SK2-Flashlight/One touch search
  5. SK3-power selectable/Emergency key
  6. LED flashlight
  7. LED Tx/Rx indicator
  8. Color LCD
  9. MENU key
  10. EXIT Key
  11. A/B key
  12. VFO/MR key
  13. Numeric keypad
  14. Speaker
  15. Power/Volume knob
  16. Speaker/Mic Jacks
  17. Navigation keys
  18. Type-C charging port
  19. Type-C charging indicator
  20. Battery tightening screw

4.2 LCD Display

The 1.77-inch color LCD provides a clear display of frequencies, channels, and various function icons. It offers two display modes: frequency and channel.

BAOFENG UV-21 Pro V2 1.77 inch larger LCD screen

Image: Close-up of the BAOFENG UV-21 Pro V2's 1.77-inch larger LCD screen, showing frequency display and battery indicator. The screen is designed for clear operation even in the dark.

LCD Icon Descriptions

IconDescription
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator (High/Low)
♪DTMF side tone audible
DCSDCS enabled
CTCSSCTCSS enabled
+TX shifted higher in frequency than RX
-TX shifted lower in frequency than RX
DDual watch enabled
🔒Keypad lock enabled
VOXVOX enabled
SCRVoice scramble function activated
NNarrowband enabled
🔋Battery level indicator
RReverse function enabled
▶Indicates active band or channel

4.3 Status Indications (LED)

The status LED provides simple visual feedback:

  • Constant Red: Transmitting.
  • Constant Green: Receiving.
  • Green and Red Alternately Flashing: No Battery.
  • Red: Charging Normally.
  • Green: Fully Charged.
  • Red Blinks Fast: Trouble (battery too warm, short-circuited, or charger short-circuited).

5. Setup and Installation

5.1 Installing/Removing the Antenna

  • Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

5.2 Installing the Belt Clip

  • At the back of the radio, remove the two parallel screws mounted above the battery. Thread them through the holes on the belt clip and screw them back into the radio body.
  • Removing: Unscrew counter-clockwise to remove the belt clip.

5.3 Installing the Battery Pack

Before attaching or removing the battery, ensure your radio is turned off by rotating the power/volume knob fully counter-clockwise.

  1. Align the battery in parallel with the radio body, with the lower edge of the battery about 1-2cm below the radio's edge.
  2. Once aligned with the guide-rails, slide the battery upward until it clicks into place.

Removing the Battery Pack

To remove the battery, press the battery release above the battery pack while sliding the battery downward.

Fixing screw for BAOFENG UV-21 Pro V2 battery

Image: Illustration of the fixing screw for the battery pack on the BAOFENG UV-21 Pro V2, emphasizing its role in ensuring a firm, secure, and waterproof connection.

5.4 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

5.5 Charging the Battery

The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times before regular use.

Using the Base Charger

  1. Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light will blink orange.
  2. Plug the battery or the radio into the charger, ensuring good contact with charging terminals. The indicator light will turn red, indicating charging.
  3. A full charge takes approximately 2-5 hours. The lamp turns green when charging is complete.
  4. Remove the battery or radio unit from the charger.

Note: If the radio is powered on while charging in the base charger, the indicator lamp may not turn green to show full charge. For accurate indication, switch off the radio during charging.

Using the Type-C USB Charger

The Type-C USB port allows convenient charging from various sources.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C charging port on your battery.
  3. Connect the other end of the USB charger to a wall power outlet, power bank, or laptop.
  4. An empty battery will be fully charged in approximately 4 hours.
  5. The battery meter on the LCD will indicate charging progress.

Note: It is recommended to power off your radio while charging. If powered on with a completely empty battery, you may not be able to transmit immediately. Allow the battery to charge to at least one bar before attempting transmission. For optimal battery life, remove the radio from the charger within 6 hours and do not store it connected to the charger.

BAOFENG UV-21 Pro V2 charging methods

Image: Demonstrates two charging methods for the BAOFENG UV-21 Pro V2: using the base charger with a wall outlet and using the Type-C USB cable with various power sources like a wall adapter, laptop, power bank, or car charger.

6. Basic Operations

6.1 Power On/Off the Radio

  • Power On: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD, followed by a frequency or channel. If voice prompts are enabled, it will announce "frequency mode" or "channel mode".
  • Power Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

6.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease. Use the monitor function (SK1 key below PTT) to adjust volume to the un-squelched static for easier setting.

6.3 Main Band/Sub Band Select (A/B Key)

In standby mode, press the [A/B] key to switch between the A (upper) and B (lower) displays. The selected display's frequency or channel becomes the active listening and transmit frequency.

6.4 VFO/Channel Switch (VFO/MR Key)

Press the [VFO/MR] key to switch between Frequency (VFO) mode and Channel (MR) mode. In Channel mode, the channel number is displayed. In Frequency mode, 'VFO' is displayed.

6.5 Frequency (VFO) Mode

In VFO mode, navigate up/down the band using the ▲/▼ keys, or input frequencies directly using the numeric keypad (e.g., [4][3][6][6][1][2][5][0] for 436.61250 MHz).

WARNING!

Just because you can program a channel does not mean you're automatically authorized to use that frequency. Transmitting on unauthorized frequencies is illegal and a serious offense. Listening is generally legal. Contact your local regulatory body for information on applicable laws.

6.6 Channel (MR) Mode and Channel Selection

Channel (MR) mode is practical for everyday use with pre-programmed channels. Navigate using the ▲/▼ keys or the encoder, or input channel numbers directly (e.g., [0][1][2] for channel 12). Voice prompts will announce the channel if enabled.

6.7 Making a Call

Note: If two channels are shown, press [A/B] to switch the main channel.

  • Channel Mode Call: Select a channel, hold [PTT] to initiate a call. Speak into the microphone. The red LED will be on.
  • Frequency Mode Call: Switch to frequency mode with [VFO/MR], input the working frequency, then hold [PTT] to transmit. The red LED will be on.
  • Receive a Call: Release [PTT] to answer. The green LED will be on when receiving.

Note: For best reception volume, keep the microphone 2.5 cm to 5 cm from your mouth during transmission. You can temporarily switch radio power by pressing [SK2] before a call.

6.8 Using the Flashlight (SK2 Key)

Press [SK2] momentarily to turn on the high-intensity LED flashlight. Press again to flash the LED (Strobe emergency mode). Press a third time to turn it off. The radio operates normally when the emergency strobe is activated.

BAOFENG UV-21 Pro V2 with high brightness flashlight

Image: The BAOFENG UV-21 Pro V2 demonstrating its high brightness flashlight feature, useful for various outdoor and low-light environments like night camping, night hunting, or basements.

6.9 Emergency Alert (SK3 Key)

To activate, press and hold [SK3] for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK3] again to exit. This feature should only be used in actual emergencies.

6.10 FM Radio (SK1 Key)

The radio can receive FM broadcasts from 65-108MHz.

  1. In frequency or channel mode, press [SK1] to turn on the radio.
  2. Select the desired radio frequency with the ▲/▼ keys or input the frequency. Press [#] to automatically search for a station.
  3. Press [SK1] to exit FM radio.

Note: While listening to FM, if a signal is received on an A/B channel, the radio will automatically switch to that channel. It will return to FM mode when the signal disappears.

6.11 Monitor (SK1 Key)

In standby, press and hold [SK1] to enter Monitor mode. This allows you to hear weak signals or signals with matched carriers but weak signaling. Release [SK1] to return to standby. If no signal is present, it will emit noise.

6.12 Keypad Lock (* Key)

To enable/disable the keypad lock, press and hold the [*] key for about two seconds. This locks all keys except the three side keys. You can also configure automatic keypad lock after ten seconds via the menu.

6.13 Frequency Reversal (* Key)

A short momentary press of the [*] key enables the reverse function, switching your transmit and receive frequencies. When active, an "R" will display on the first line of the screen.

6.14 TX Repeaters Tone (PTT + SK2 Key)

Press [PTT] + [SK2] to send a 1750Hz repeater tone. This is useful for communicating through repeaters. This function works even if the keypad lock is enabled.

6.15 One Touch Frequency Search (SK2 Key)

  1. Press and hold [SK2]. The screen will display “SEARCH SEARCH...”. The radio acts as a receiver.
  2. If a stable signal is received, the frequency and any CTCSS/DCS values will be displayed. If no CTCSS/DCS, "NONE" is displayed.
  3. Press the [MENU] key to save the Search frequency and CTCSS or DCS to a channel.

Note: During frequency search, press [#] to switch between UHF or VHF bands.

BAOFENG UV-21 Pro V2 2-second copy frequency feature

Image: Demonstrates the 2-second copy frequency feature of the BAOFENG UV-21 Pro V2, showing how to decode another walkie talkie's frequency by powering on, pressing the 'up' arrow to search, holding the transmitting radio's PTT, and confirming the found frequency to start communicating.

6.16 Weather Radio/Scan Weather Channel (NOAA)

Your radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan all 10 NOAA Weather channels.

  1. To turn on NOAA Weather Scan, press and hold the [0sQL] key for 3 seconds. The radio will enter Weather band mode.
  2. Press and hold the [#] key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Pressing and holding [#] again will stop the scan.
  3. After stopping the scan, you can manually select a weather channel using the ▲/▼ keys.
  4. To exit Weather Radio broadcast mode, press the [MENU] key or [PTT] key.

Weather Channel Frequencies and Names

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

BAOFENG UV-21 Pro V2 NOAA Weather Channel

Image: The BAOFENG UV-21 Pro V2 displaying the NOAA Weather Channel feature, emphasizing its ability to provide weather information to help avoid hazards, shown against a backdrop of severe weather, a damaged road, and a volcanic eruption.

7. Advanced Features and Customization

7.1 Working the Menu System

The radio's menu system allows customization of various settings. Refer to Appendix B (Shortcut Menu Operations) for a complete list of menu items and parameters.

Basic Menu Navigation (Arrow Keys)

  1. Press the [MENU] key to enter the menu.
  2. Use the ▲/▼ keys to navigate between menu items.
  3. Press [MENU] again to select a menu item.
  4. Use the ▲/▼ keys to select the desired parameter.
  5. To confirm, press [MENU] (saves setting and returns to main menu). To cancel, press [EXIT] (resets item and exits menu).
  6. To exit the menu at any time, press the [EXIT] key.

Menu Shortcuts (Numeric Keypad)

Each menu item has a numerical value for direct access.

  1. Press the [MENU] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. Press the [MENU] key to enter the item.

7.2 Scanning (Menu 21)

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. Dual Watch is inhibited during scanning.

To enable the scanner, press and hold the [#] key for about two seconds. Press and hold [#] again to exit scanning mode.

Scanning Modes

The scanner has three modes of operation:

  • Time Operation (TO): Scanner stops when a signal is detected and resumes after a preset time.
  • Carrier Operation (CO): Scanner stops when a signal is detected and resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops when a signal is detected. To resume, press and hold [#] again.

Setting Scanner Mode

  1. Press [MENU].
  2. Enter [2][1] for scanner mode.
  3. Press [MENU] to select.
  4. Use ▲/▼ keys to select the desired scanning mode.
  5. Press [MENU] to confirm and save.
  6. Press [EXIT] to exit the menu.

Frequency Scanning

In frequency mode, press and hold [#] for more than 2 seconds to start scanning. Change direction with ▲/▼ keys. Press [#] to stop.

Channel Scanning

In channel mode, press and hold [#] for more than 2 seconds to start scanning. Change direction with ▲/▼ keys. Press [#] to stop.

Scan CTCSS (Menu 14)

Allows scanning for frequencies with CTCSS tone enabled. In standby, press [MENU], then [1][4] to display “Scan CTCSS”. Press [MENU] to start scanning CTCSS tones.

Scan DCS (Menu 15)

Allows scanning for frequencies with DCS code enabled. In standby, press [MENU], then [1][5] to display “Scan DCS”. Press [MENU] to start scanning DCS codes.

Note: Scan CTCSS/DCS cannot be activated in Channel mode. Scanning starts only when the receiving band detects a signal.

7.3 Manual Programming (Channels Memory)

The radio has 999 memory channels. Each channel can store receive/transmit frequencies, power, signaling, bandwidth, ANI/PTT-ID settings, and a 6-character alphanumeric identifier.

Frequency Mode vs. Channel Mode

In standby, press [VFO/MR] to switch between VFO and MR modes. VFO mode is for temporary frequency assignments, while MR mode is for selecting preprogrammed channels.

Example: Programming a Channel Repeater Offset with CTCSS Tone

To program a new memory in Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), and TX CTCSS tone 123.0:

  1. Press [MENU] to switch between menus.
  2. Press [VFO/MR] to set the radio to VFO mode (VFO icon displayed).
  3. Press [MENU], then [3][1] [1][0] to delete prior data in channel 10.
  4. Press [MENU], then [1][2] [1][2][3][0] to select desired TX encode tone (123.0).
  5. Enter RX frequency (e.g., 43255000).
  6. Press [MENU], then [3][0] [1][0] to enter the desired channel (10). RX has been added.
  7. Enter TX frequency (e.g., 43755000).
  8. Press [MENU], then [3][0] [1][0] to enter the same channel (10). TX has been added.
  9. Press [VFO/MR] to return to MR mode (channel number reappears).

7.4 Repeaters Programming

This assumes you know your repeater's transmit/receive frequencies and are authorized to use it.

  1. Press [VFO/MR] to set the radio to VFO mode (VFO icon displayed).
  2. Use the numeric keypad to enter the repeater's output (receiving) frequency.
  3. Press [MENU].
  4. Enter [2][9] for frequency offset.
  5. Press [MENU] to select.
  6. Use the numerical keypad to enter the specified frequency offset.
  7. Press [MENU] to confirm and save.
  8. Enter [2][8] for offset direction.
  9. Use the ▲/▼ keys to select + (positive) or - (negative) offset.
  10. Press [MENU] to confirm and save.
  11. (Optional) Save to memory (see Manual Programming) or set up CTCSS.
  12. Press [EXIT] to exit the menu.

Note: If you experience connection problems, check your settings or repeat the procedure. Some Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open. See "1750Hz Tone-burst" for details. If issues persist, contact the radio system administrator or local amateur radio club.

7.5 VOX (Voice Operated Transmit)

This function enables hands-free conversations. Speak into the microphone to automatically activate transmission.

To enable/disable VOX (Menu 7):

  1. In standby, press [MENU], then [7]. The screen displays “VOX”.
  2. Press [MENU].
  3. Use ▲/▼ keys to turn off VOX or select VOX level (1-10).
  4. Press [MENU] to confirm.
  5. Press [EXIT] to return to standby.

Note: Level 1 is the least sensitive, level 9 is the most sensitive. VOX is not enabled in Scan or FM Radio mode.

7.6 Dual Watch

This feature allows monitoring two channels simultaneously by rapidly switching between them. The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two monitored channels.

To enable/disable Dual Watch mode (Menu 7):

  1. Press [MENU].
  2. Enter [7] for Dual Watch.
  3. Press [MENU] to select.
  4. Use ▲/▼ keys to enable or disable.
  5. Press [MENU] to confirm.
  6. Press [EXIT] to exit the menu.

7.7 Stopwatch Timer (Menu 44)

To activate the stopwatch timer:

  1. In standby, press [MENU], then [4][4]. The screen displays “STOP WATCH”.
  2. Press [MENU] to enter the function.
  3. Use ▲/▼ keys to enable (ON) the function.
  4. Press [MENU] for confirmation.
  5. Press [EXIT] to return to standby.

When ON, press [MENU] to start counting. Press [MENU] again to re-start counting. To exit, stop counting first, then press [EXIT].

7.8 Scrambler (Menu 45)

The scrambler protects communications by voice inversion, preventing unauthorized listening. The "SCR" icon appears when enabled.

To activate scrambler (Menu 45):

  1. In standby, press [MENU], then [4][5]. The screen displays “SCRAMBLE”.
  2. Press [MENU] to enter.
  3. Use ▲/▼ keys to select the scramble mode (MODE1 to MODE3).
  4. Press [MENU] to confirm.

7.9 DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method using dual sinusoidal signals. It's commonly used in two-way radio systems for automation and remote control, such as activating amateur radio repeaters.

DTMF Frequencies and Corresponding Codes

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

To send DTMF codes, press the key(s) corresponding to the message while holding down the PTT key.

7.10 Customization Options

The radio allows customization of visual and audible features:

  • Display Backlight (ABR) - Menu 7: Set always on or delay time (5/10/15/20 seconds).
  • Beep Prompt (BEEP) - Menu 8: Enable/disable key press tones.
  • Voice Function (VOICE) - Menu 17: Enable/disable voice prompts.
  • Language of the Menu (LANGUAGE) - Menu 18: Select English or Chinese.
  • Working Mode (MDF-A) - Menu 24: Choose display mode (Frequency, Channel, Channel Name).
  • Roger Beep (ROGER) - Menu 36: Enable/disable end of transmission tone.
  • Power On Message (POWER ON MSG) - Menu 40: Customize welcome message (Voltage, Message, Logo, Model Name).
  • Power On Password (POWER ON PWD) - Menu 43: Set a password to turn on the radio.

7.11 Reset (Menu 42)

The transceiver has two reset modes:

  • Reset VFO: Returns all settings except channels to default.
  • Reset ALL: Returns all settings to default.

To perform a reset:

  1. In standby, press [MENU], then [4][2]. The screen displays “RESET”.
  2. Press [MENU].
  3. Use ▲/▼ keys to select VFO or ALL.
  4. Press [MENU] to confirm.
  5. The display shows “Sure to reset?”. Press [MENU] again to confirm. The transceiver will turn off and reboot.

8. Troubleshooting Guide

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery improperly installed, power run out, dirty/damaged contacts, low battery voltage.Reattach/replace battery, clean contacts, recharge.
Weak or intermittent voice during reception.Low volume, loose/incorrect antenna, blocked speaker.Increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Inconsistent frequency/signaling type, too far from others.Verify TX/RX frequency/signaling type, move closer.
Unknown voices or noise.Interrupted by other radios, analog mode with no signaling, too far from others.Change frequency, adjust squelch, request dealer to set signaling.
Unable to hear anyone due to too much noise/hiss.Unfavorable position (blocked by buildings/underground), external electromagnetic interference.Move to open area, restart radio, stay away from interfering equipment.
Radio keeps transmitting.VOX turned on, headset not installed correctly.Turn off VOX, check headphones.

Note: If these solutions do not resolve your problems, contact your dealer for technical support.

9. Technical Specifications

ParameterSpecification
Frequency Range136-174MHz (TX&RX), 220-260MHz (TX&RX), 400-520MHz (TX&RX), FM65-108MHZ (RX), AM108-136MHz (RX), Police350-390MHz (RX)
Output Power (w)5w-10w (High Power)
Channel Spacing25.0KHz (Wide)/12.5KHz (Narrow)
Storage Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Transmission current≤1800mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna Impedance50 Ohm
Battery Capacity (mAh)High-Capacity
Waterproof / Water-ResistantNo
Battery IncludedYes
MaterialPlastic
Is_DisplayYes
Maximum Range5km-10km
UseMotor vehicle

Note: All specifications may be modified without prior notice or liability.

10. User Tips

  • Licensing: Be aware that operating this radio on certain frequencies (e.g., GMRS) may require a license in your region. Ensure you comply with local regulations.
  • Communication: Two units can communicate with each other. For optimal performance, ensure both radios are on the same frequency and signaling type.
  • Range: Users report good range, achieving 2 kilometers in city environments without problems, and up to 5-10 KM in open areas like sandy beaches.
  • Audio Quality: The radio offers good audio and excellent reception and transmission quality.
  • Programming: While the radio can be programmed via computer software, most settings can also be adjusted directly through the keypad menu. This includes adding/deleting memory channels, adjusting VOX/squelch/power save levels.
  • Troubleshooting Static/No Channels: If you experience only static signals or cannot receive channel conversations, verify your frequency and signaling type settings. Ensure the radio is properly programmed for the channels you intend to use. If using frequency mode, ensure you are tuned to an active frequency.
  • Programming Software: Programming software for this device is typically available from the seller or manufacturer's website.

11. Support

For detailed technical information, advanced programming instructions, and further assistance, please refer to the official user manual PDF. You can view the full user manual here.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.