Introduction
This manual provides essential information for the installation, operation, and maintenance of the FGHGF CDZ03RR Charger Circuit Board. This component is designed as a replacement power board for the charging piles of Roborock E25 and E35 robotic vacuum cleaners. Please read this manual thoroughly before attempting any installation or repair.

Specifications
| Feature | Detail |
|---|---|
| Brand Name | FGHGF |
| Model Number | CDZ03RR |
| Vacuum Part Type | Motors (component category) |
| Type | Vacuum Cleaner Parts |
| Specific Type | Charger Circuit Board |
| Origin | Mainland China |
| Package Length | 17 cm |
| Package Width | 12 cm |
| Package Height | 12 cm |
| Package Weight | 0.25 kg |
Compatibility
This charger circuit board is specifically designed for use with the charging piles of the following robotic vacuum cleaner models:
- Xiaomi Roborock E25
- Xiaomi Roborock E35
Ensure your vacuum cleaner model matches one of the listed compatible models before proceeding with installation.
Package Contents
Upon opening the package, you should find the following item:
- 1x CDZ03RR Charger Circuit Board
Inspect the board for any visible damage before installation.
Installation and Setup
WARNING: Disconnect the charging pile from all power sources before attempting installation. Failure to do so may result in electric shock or damage to the device. If you are not comfortable performing this repair, seek assistance from a qualified technician.
The CDZ03RR is a replacement circuit board for the charging pile. Installation typically involves opening the charging pile casing, carefully removing the old board, and installing the new one. Follow these general steps:
- Power Disconnection: Ensure the Roborock charging pile is completely unplugged from the wall outlet.
- Access Casing: Carefully open the casing of the charging pile. This may involve removing screws or prying open clips. Refer to your Roborock charging pile's specific service manual or diagrams for precise instructions on opening the casing.
- Locate Old Board: Identify the existing charger circuit board within the charging pile.
- Disconnect Wires: Take clear photos of all wire connections to the old board before disconnecting them. Carefully disconnect all wires and connectors from the old circuit board. Note their positions for correct re-connection.
- Remove Old Board: Unscrew or unclip the old circuit board from its mounting points.
- Install New Board: Position the new CDZ03RR circuit board in the same location as the old one and secure it with screws or clips.
- Reconnect Wires: Using your reference photos, carefully reconnect all wires and connectors to the new CDZ03RR circuit board. Ensure all connections are firm and correctly oriented.
- Close Casing: Once all connections are secure and the board is mounted, carefully close the charging pile casing, ensuring no wires are pinched.
- Test Functionality: Plug the charging pile back into a power outlet and test its functionality with your Roborock E25/E35 vacuum cleaner.

Operation
The FGHGF CDZ03RR Charger Circuit Board operates passively within the Roborock E25/E35 charging pile. Once correctly installed, it facilitates the power management and charging functions of the dock. There are no direct user controls on the circuit board itself. Its proper operation is indicated by the charging pile functioning as expected, including power indicator lights and successful charging of the vacuum cleaner.
Maintenance
As an internal electronic component, the CDZ03RR circuit board requires minimal maintenance. However, to ensure longevity and reliable performance:
- Keep Dry: Ensure the charging pile and its internal components remain dry. Moisture can severely damage electronic circuits.
- Cleanliness: Periodically, and with the power disconnected, you may gently clean the interior of the charging pile to remove dust accumulation, which can impede heat dissipation. Use a soft, dry brush or compressed air.
- Inspect Connections: During any routine inspection or if issues arise, ensure all wire connections to the circuit board are secure and free from corrosion.
Troubleshooting
If the charging pile does not function correctly after replacing the circuit board, consider the following troubleshooting steps:
- No Power/Charging:
- Verify the charging pile is securely plugged into a working wall outlet.
- Double-check all wire connections to the new circuit board, ensuring they match the original configuration (refer to your installation photos).
- Ensure the new circuit board is correctly seated and secured.
- Incorrect Model: Confirm that the CDZ03RR circuit board is indeed the correct replacement part for your specific Roborock E25 or E35 charging pile model.
- Professional Assistance: If the issue persists after checking all connections and confirming compatibility, it is recommended to consult a qualified electronics repair technician or the vacuum cleaner manufacturer's support.
User Tips
While no specific user tips were provided for this product, general advice for electronic component replacement includes:
- Always work in a well-lit, clean, and static-free environment.
- Use appropriate tools for disassembly and reassembly to avoid damaging components or fasteners.
- Keep track of all screws and small parts during disassembly to ensure proper reassembly.
Warranty and Support
For information regarding warranty coverage, return policies, or technical support for the FGHGF CDZ03RR Charger Circuit Board, please contact the seller or the manufacturer directly. Keep your purchase receipt as proof of purchase.