PowMr POW-M60-MAX

Contents

PowMr POW-M60-MAX 60A MPPT Solar Charge Controller

User Manual

1. Introduction and Overview

The PowMr POW-M60-MAX is an advanced 60A Maximum Power Point Tracking (MPPT) solar charge controller designed to efficiently regulate the voltage from your solar panels to charge various battery types in 12V, 24V, 36V, and 48V systems. It features a customized large LCD screen for easy monitoring and configuration, along with multiple protection functions to ensure safe and reliable operation of your solar power system.

PowMr POW-M60-MAX MPPT Solar Charge Controller front view with features listed

Front view of the PowMr POW-M60-MAX MPPT Solar Charge Controller highlighting its features.

2. Safety Instructions

  • Ensure all wiring is correctly connected and securely fastened before operation.
  • Always connect the battery to the controller first, then the solar panels, and finally the load. Disconnect in the reverse order.
  • Avoid installing the solar charge controller in direct sunlight, high-temperature environments, or areas prone to water ingress.
  • Ensure adequate air circulation around the controller for proper cooling. Leave a space of at least 150 mm (approximately 6 inches) above and below the unit.
  • The controller is equipped with multiple protections including overcurrent, short circuit, reverse polarity, and over-temperature protection. However, proper installation and handling are crucial.
  • Do not attempt to repair or modify the controller yourself. Refer to qualified personnel for service.

3. Package Contents

Upon opening the package, please verify that all the following items are included:

  • PowMr POW-M60-MAX MPPT Solar Charge Controller
  • Special cable with terminals
  • User Manual
  • Additional special cable terminals
  • Screws/bolts for mounting
Package contents of the PowMr POW-M60-MAX solar charge controller, including the controller, cables, manual, and mounting hardware.

Contents included in the PowMr POW-M60-MAX package.

4. Product Features

  • Advanced MPPT Technology: Achieves maximum efficiency of ≥ 98% and PV utilization of ≥ 99% for optimal power harvesting.
  • Wide Battery Compatibility: Automatically detects 12V, 24V, 36V, and 48V battery systems. Compatible with various battery types including GEL, FLD (Flooded), SLD (Sealed Lead-Acid), LFE (LiFePO4), USE (User-defined), and LI (Lithium).
  • Backlit LCD Screen: Features a customized large screen for clear display of PV parameters, battery parameters, and load working settings, enhancing user experience.
  • Multiple Protection Functions: Includes protection against maximum charging current limit, PV array short circuit, PV input overcurrent, controller overload, load short circuit, PV reverse polarity, and over-temperature.
  • Efficient Heat Dissipation: The back plate is made of aviation-grade die-casting aluminum, providing low noise and excellent heat dissipation through natural convection.
  • 3-Stage Charging Mode: Utilizes Bulk Charge, Boost Charge, and Float Charge stages to prolong battery lifespan.
  • Easy Plug & Play Connection: Designed for convenient and straightforward installation.
  • High Input Capacity: Supports a maximum PV array open circuit voltage of 160V and maximum PV input power up to 2800W (for 48V systems).
Diagram illustrating advanced MPPT technology with over 98% efficiency and 99% PV utilization.

Advanced MPPT Technology for high efficiency.

Image showing the solar charge controller compatible with multiple battery types like GEL, LI, FLD, SLD, LFE, USE, and featuring 3-stage charging.

Compatibility with various battery types and 3-stage charging modes.

Diagram showing multiple protection features of the solar charge controller and its aluminum heat dissipation fins.

Multiple protection features and efficient aluminum heat dissipation.

5. Specifications

ParameterValue
Model NumberPOW-M60-MAX
Brand NamePowMr
Maximum Current60A
Battery Voltage12V / 24V / 36V / 48V Auto
Max PV Array Open Circuit Voltage160V
Max PV Input Power (12V System)720W
Max PV Input Voltage (12V System)DC20V~DC80V
Max PV Input Power (24V System)1440W
Max PV Input Voltage (24V System)DC37V~DC105V
Max PV Input Power (36V System)2100W
Max PV Input Voltage (36V System)DC50V~DC160V
Max PV Input Power (48V System)2800W
Max PV Input Voltage (48V System)DC72V~DC160V
ApplicationCharger Controller, Voltage Controller, Lighting Controller, Solar System Controller, Solar Working Station
Is Smart DeviceYes
Cooling WayForced air cooling
CertificationCE, FCC, RoHS
Warranty12 Months
Solar Connect Diagram showing maximum PV array open circuit voltage and input solar power/voltage for different battery systems.

Detailed specifications for PV input power and voltage across different battery systems.

6. Setup and Installation

6.1 Selecting an Installation Location

  • Choose a location that avoids direct sunlight, high temperatures, or areas where water might enter.
  • Ensure the surrounding area of the solar charge controller allows for sufficient air flow to facilitate cooling.
  • Leave a minimum space of 150 mm (approximately 6 inches) both above and below the controller to ensure natural heat loss through convection.

6.2 Fixing the Solar Charge Controller

  • Use a pen to mark the positions of the four mounting holes on the installation surface.
  • Drill holes of suitable size at the marked positions.
  • Fix the solar charge controller using the provided screws/bolts.

6.3 Wiring Connections

Follow the wiring sequence carefully to prevent damage to the controller or other components:

  1. Prepare Load-Side Wiring: If connecting a load directly to the controller, assemble the load-side wiring and terminals as needed. This may involve compressing terminals onto wires and inserting them into the contact carrier.
  2. Connect to the Battery: Connect the battery cables to the battery terminals on the controller. Ensure correct polarity (positive to positive, negative to negative).
  3. Start the Controller: Once the battery is connected, the controller should power on.
  4. Connect the PV (Solar Panels): Connect the solar panel cables to the PV input terminals on the controller. Ensure correct polarity.
  5. Connect the Load (Optional): If using the load output terminals, connect your DC load to these terminals.

Video demonstrating the unboxing and basic connection steps for the PowMr POW-M60-MAX.

Diagram showing how to clamp terminals and insert them into the controller's ports during installation.

Visual guide for connecting terminals to the controller.

7. Wiring Diagram

The following diagram illustrates a typical solar power system setup using the PowMr POW-M60-MAX MPPT Solar Charge Controller:

Comprehensive solar connection diagram showing solar panels connected to the MPPT controller, which then connects to a battery bank, and an inverter for household appliances.

Solar Connect Diagram: How the system works.

  • Solar Panels: Connect to the PV input terminals of the MPPT controller.
  • MPPT Solar Charge Controller: Regulates power from solar panels to the battery and load.
  • Battery: Connect to the battery terminals of the MPPT controller. This stores energy.
  • Inverter: Connects to the battery to convert DC power to AC power for household appliances.
  • Load: Can be connected directly to the controller's load terminals (DC loads) or via an inverter (AC loads).

8. Operating Instructions

The controller features a backlit LCD screen and four function keys for easy operation:

  • PV button: View PV voltage/PV current.
  • BAT/▲ button: View battery information, adjust values, set battery type.
  • DC/▼ button: Set load mode, adjust values.
  • SET/⚙ button: Save/reset parameters.
Backlit LCD screen of the solar charge controller showing PV parameters, battery parameters, load working settings, and MPPT working modes.

LCD screen and function keys for monitoring and setting parameters.

8.1 MPPT Working Modes

The controller operates in different modes depending on the system status:

  • 3.0: Night mode, no charging.
  • 4.0: Bulk charging mode (MPPT mode).
  • 7.0: Boost charging mode.
  • 8.0: Float charging mode.

8.2 Load Working Modes (LODE)

You can configure the load output behavior using the DC/▼ button:

  • 24H (Default): Load is continuously on.
  • Solar Light Control Mode: Load turns on at sunset and turns off at sunrise.
  • Adjust Load Enable Duration (01~23H): Set a specific duration (in hours) for the load to be active after sunset.

9. Battery Parameter Setup

To view and adjust battery parameters, press the BAT/▲ button. You can cycle through various information displays:

  • Current Battery Voltage
  • Boost Charging Voltage
  • Float Charging Voltage
  • Charging Current
  • Battery Type
  • Low DC Recovery Cut-off Voltage
  • Equipment Temperature
  • Battery Calibration Voltage
  • Low DC Cut-off Voltage

9.1 Selecting Battery Type

It is crucial to select the correct battery type for optimal charging and battery health. To set the battery type:

  1. Navigate to the "Battery Type" parameter using the BAT/▲ button.
  2. Use the BAT/▲ or DC/▼ keys to select the desired battery type from the list below.
  3. Press the SET/⚙ button to confirm your selection.
SequenceDisplayBattery Type
1SBLSealed lead acid battery
2USEUser-defined
3N14Ternary lithium battery
4N13Ternary lithium battery
5N07Ternary lithium battery
6N06Ternary lithium battery
7N03Ternary lithium battery
8L16Lithium iron phosphate battery
9L15Lithium iron phosphate battery
10U08Ternary lithium battery
11L04Lithium iron phosphate battery
12FLdFlooded lead acid battery
13GELColloidal lead acid battery
Diagram showing battery parameter setup and battery type selection on the controller's LCD screen.

Battery parameter setup and type selection interface.

9.2 Battery Voltage Calibration

The battery calibration voltage parameter is used to correct the current battery voltage measured by the controller. This ensures accurate readings and optimal charging.

  1. Once the parameter switches to "battery calibration voltage" item, press and hold BAT/▲ key to enter the battery voltage calibration setting.
  2. Then press the BAT/▲ or DC/▼ keys to calibrate the battery voltage parameters of the controller according to the battery voltage measured by a multimeter.
  3. Finally, press SET/⚙ to confirm.
Instructions for calibrating battery voltage using a multimeter and the controller's buttons.

Battery voltage calibration process.

10. Maintenance

  • Regularly inspect all wiring connections for tightness and corrosion.
  • Keep the controller clean and free from dust and debris to ensure proper heat dissipation.
  • Check the battery terminals for any signs of corrosion and clean if necessary.
  • Monitor the LCD display for any error codes or unusual readings.
  • Ensure the ventilation openings are not blocked.

11. Troubleshooting

If you encounter issues, consider the following common problems and solutions:

  • No display or power: Check battery connections and ensure the battery has sufficient charge.
  • No charging from PV: Verify solar panel connections, check for shading, and ensure PV voltage is within the controller's operating range.
  • Load not working: Check load connections, ensure the load mode is correctly set (e.g., not in night mode if you expect it to be on), and verify the battery has enough charge.
  • Incorrect voltage readings: Perform battery voltage calibration as described in Section 9.2.

For specific issues like "how many watts it charges at 12V", refer to the Specifications table (Section 5) for the maximum PV input power for each system voltage.

12. User Tips

  • Wiring Sequence is Key: Always connect the battery first, then the solar panels, and finally the load. Disconnect in the reverse order (load, then PV, then battery). This prevents voltage spikes that can damage the controller.
  • Match Battery Type: Ensure you select the correct battery type in the controller settings to optimize charging and extend battery life. Incorrect settings can lead to undercharging or overcharging.
  • Monitor Performance: Regularly check the LCD display for PV input, battery voltage, and charging current to ensure your system is operating efficiently.
  • Consider Accessories: For a robust and safe system, consider using recommended accessories like solar extension cables, proper solar connectors, and circuit breakers/fuses.

13. Warranty and Support

The PowMr POW-M60-MAX Solar Charge Controller comes with a 12-month warranty. For any technical support, warranty claims, or further assistance, please contact your seller or the manufacturer directly. Keep your purchase receipt as proof of purchase.

To enhance the performance and safety of your solar power system, consider these recommended accessories:

AccessoryImageDescription
10AWG Solar Extension Cable10AWG Solar Extension CableMade of tin-plated conductive copper material for good electrical conductivity. Features excellent PPO insulation, flame retardancy, high strength, abrasion, and corrosion resistance. IP67 waterproof for outdoor use (-40℉ ~ +194℉).
Solar Connector (Male & Female Plug)Solar Connector Male & Female PlugRated for 1500Vdc and waterproof, ensuring secure and reliable connections for your solar panels.
Solar Circuit Breaker with Replaceable FusesSolar Circuit Breaker with Replaceable FusesEasy to plug and compatible with solar PV connectors. Features replaceable fuses, high current carrying capacity, PPO housing for high temperature and abrasion resistance, and IP68 waterproof rating.
Reset Circuit Breaker Fuse Holder with Manual Inline FuseReset Circuit Breaker Fuse Holder with Manual Inline FuseSuitable for car audio/video and home solar system overload protection. Made from alloy material with good electrical conductivity. Switch type, easy to operate, and can be mounted on a panel or firewall.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.