Ozito SG-T12

Contents

T12 Cordless Soldering Iron Instruction Manual

Model: SG-T12

1. Introduction

This manual provides instructions for the safe and efficient operation of your T12 Cordless Soldering Iron. This portable soldering station is designed for use with Ozito 18V lithium batteries, offering quick heating and precise temperature control for various soldering tasks.

T12 Cordless Soldering Iron with battery adapter and soldering handle

Figure 1: T12 Cordless Soldering Iron (Battery not included)

2. Safety Information

Always observe basic safety precautions when using electrical tools to reduce the risk of fire, electric shock, and personal injury.

  • Ensure the work area is well-ventilated.
  • Wear appropriate personal protective equipment, including safety glasses.
  • Do not touch the soldering iron tip when hot.
  • Always place the soldering iron in its stand when not in use.
  • Keep out of reach of children.
  • This device is designed for use with Ozito 18V lithium batteries. Using incompatible batteries may cause damage or injury.
  • The soldering station features undervoltage protection (default 15.5V) to prevent battery damage.

3. Specifications

Product and Working Parameter Table

Figure 2: Product and Working Parameters

Product Parameters:

ParameterValue
Model NumberSG-T12
DisplayOLED
Handle InterfaceGX12-4pins
Product Weight6.35 oz
Host Dimensions (L x W x H)4.33 x 4.72 x 2.76 inch
Handle Wire Length1.1m
Application Iron TipT12 series

Working Parameters:

ParameterValue
Time to Melt Tin<8 seconds
Max Power80 W
Temperature Range392°F - 896°F (200°C - 480°C)
Power Voltage18V-24V, 4.5A
Power SourceBattery-Powered (Ozito 18V lithium batteries)
Sleep Time2 minutes

4. Package Contents

Please check the package contents upon receipt:

  • 1 x Welding Station (main unit)
  • 1 x Welding Handle (soldering iron)
  • 1 x Instruction Manual

Note: Batteries and welding wires are NOT included.

Contents of the package including welding station, handle, and manual

Figure 3: Included Components

5. Setup

  1. Attach Battery: Insert a compatible Ozito 18V lithium battery into the battery slot on the main welding station unit. Ensure it clicks securely into place.
  2. Connect Soldering Handle: Connect the GX12-4pins interface of the soldering handle to the corresponding port on the welding station.
  3. Power On: Locate the power switch on the welding station and turn it to the 'ON' position.
  4. Initial Check: The 1.3-inch OLED display should illuminate, showing real-time set temperature, working temperature, voltage, and other parameters.

Video 1: Assembly and basic operation of the T12 Soldering Iron.

T12 Cordless Soldering Station connected to a battery

Figure 4: Soldering station with battery attached.

6. Operating Instructions

6.1 Display Overview

Diagram of the 1.3 inch OLED display showing various indicators

Figure 5: OLED Display Indicators

  • 1. Real-Time Set Temperature: Displays the target temperature.
  • 2. Vibration Prompt: Indicates vibration feedback (e.g., for sleep mode wake-up).
  • 3. STC Usage: Shows the usage status of the STC (Soldering Tip Controller).
  • 4. Real-Time Voltage: Displays the current battery voltage.
  • 5. Real-Time Working Temperature: Shows the actual temperature of the soldering tip.
  • 6. Internal Temperature of the Machine: Displays the internal temperature of the main unit.

6.2 Temperature Adjustment

The soldering iron features an intuitive one-knob control for temperature adjustment. Rotate the knob to increase or decrease the set temperature within the range of 392°F - 896°F (200°C - 480°C).

One knob control for temperature and menu settings

Figure 6: Intuitive One Knob Control

6.3 BOOST Function

To temporarily increase the soldering temperature for larger solder joints, use the BOOST function:

  • Short press the encoder knob to activate the BOOST function.
  • You can set the BOOST duration (0-99 minutes) and the temperature increase (10-80 degrees) via the menu.

6.4 Menu Settings

The single knob control also allows access to various settings. Press and hold the knob to enter the menu. Rotate the knob to navigate and press to select. Options include:

  • Temp. Calibration
  • Auto Sleep
  • Auto Poweroff
  • Boost Duration
  • Boost Degree
  • Wakeup Method
  • Buzzer Switch
  • Battery Guard
  • Convert Units (Fahrenheit/Celsius)

6.5 Battery Guard Function

Diagram showing battery guard and restore default settings

Figure 7: Battery Guard and System Settings

The soldering station has a built-in battery guard function to protect your battery. The default undervoltage protection is set to 15.5V. If the battery voltage is unstable, too high, or too low, the system will automatically adjust or cut off power to prevent damage. The setting range for this function is 12V-24V. Typically, no adjustment is needed.

7. Maintenance

  • Tip Cleaning: Regularly clean the soldering iron tip with a damp sponge or brass wool to remove oxidation and solder residue.
  • Tip Replacement: Replace worn or damaged soldering tips with compatible T12 series tips.
  • Storage: When not in use, ensure the soldering iron is cooled down and stored in a dry, safe place.
  • Battery Care: Follow the manufacturer's instructions for your Ozito 18V battery for charging and storage.
  • General Cleaning: Wipe the main unit and handle with a soft, dry cloth. Do not use abrasive cleaners or solvents.

7.1 Restore Default Settings

If you encounter unexpected behavior or wish to reset all custom settings, you can restore the device to factory defaults. Navigate to the "Restore default" option in the menu (refer to Figure 7). Important: Before restoring, back up any important parameters such as temperature calibration values or custom boost settings, as these will be lost.

8. Troubleshooting

ProblemPossible CauseSolution
Soldering iron not heating up.Battery not connected or discharged; Power switch off; Faulty soldering tip.Ensure battery is properly inserted and charged. Turn on the power switch. Replace the soldering tip.
Temperature display is inaccurate.Needs calibration.Perform a temperature calibration via the menu settings.
Device shuts off unexpectedly.Battery low; Undervoltage protection activated.Recharge or replace the battery. Check battery guard settings if issue persists with charged battery.
Knob control unresponsive.Software glitch; Physical damage.Try restarting the device. If problem persists, contact support.

9. User Tips

  • For optimal performance, ensure your Ozito 18V battery is fully charged before starting a soldering session.
  • Utilize the BOOST function for quick temperature increases when working with components that require more heat, such as larger pads or wires.
  • The OLED display provides clear, real-time feedback on temperature and voltage, allowing for precise control.
  • Take advantage of the compact and lightweight design for on-the-go repairs and projects where a power outlet is not readily available.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2023 [Manufacturer Name/Brand]. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.