CENTURY AOKE 1K40A+AK-QY

Contents

DC 12V 40A Relay Remote Control Switch User Manual

Model: 1K40A+AK-QY | Brand: CENTURY AOKE

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your DC 12V 40A Relay Remote Control Switch. This wireless control system is designed for universal applications in industrial control and low-voltage power systems, offering convenient remote operation of various electrical devices.

Remote Control Switch Receiver and Two Transmitters
Figure 1: Remote Control Switch Receiver and Two Transmitters

2. Safety Information

  • Ensure the power supply is disconnected before any installation or wiring to prevent electric shock.
  • Verify that the input and output voltages match the device specifications (DC 12V).
  • Do not exceed the maximum load current of 40A or maximum power of 350W to avoid damage to the relay or connected devices.
  • Keep the device away from water, moisture, and extreme temperatures.
  • Installation should be performed by qualified personnel if you are unsure about electrical wiring.

3. Package Contents

  • 1 x 12V1K40A Receiver Module
  • 2 x AK-QY Remote Transmitters

4. Specifications

4.1 Receiver (Model No.: 12V1K40A)

FeatureSpecification
Working VoltageDC 12V
Working Temperature-40°C to +80°C
Receiver Sensitivity> -105dBm
Working Frequency433MHz
Output VoltageDC 12V (Input voltage = Output voltage)
Max Load Current40A
Max Power350W (Note: 12V * 40A = 480W. The device is marked MAX 350W. Please ensure your load does not exceed 350W to prevent damage.)
Dimensions8.2 x 5.0 x 3.1 cm
Receiver Module Dimensions
Figure 2: Receiver Module Dimensions

4.2 Transmitter (Model No.: AK-QY)

FeatureSpecification
Buttons2 Buttons (ON/OFF)
Working VoltageDC 6V (2 x CR2016 batteries)
Operating Frequency433MHz
Remote Distance20-50 meters
Operating Current13 mAh
EncodeEV1527 code
Dimensions5.7 x 3.2 x 1.1 cm
Remote Transmitter Dimensions
Figure 3: Remote Transmitter Dimensions

5. Setup

5.1 Wiring the Receiver

The receiver is designed for simple wiring. Ensure all connections are secure and correctly polarized (IN+ to positive, IN- to negative, OUT+ to positive load, OUT- to negative load).

  1. Connect your DC 12V power source to the 'IN+' and 'IN-' terminals on the receiver.
  2. Connect your DC 12V load (e.g., light, fan) to the 'OUT+' and 'OUT-' terminals on the receiver.
Wiring Diagram: Input and Output Connections
Figure 4: Wiring Diagram for Input and Output Connections
Simple Wiring Example: DC 12V Power to Light
Figure 5: Simple Wiring Example (DC 12V Power to Light)
Receiver Terminal Connections Detail
Figure 6: Receiver Terminal Connections Detail

6. Operating Instructions

The receiver's working mode is changed by pressing the learning button. The LED indicator on the receiver will flash a specific number of times to confirm the mode change.

6.1 Learning (Pairing) Method

  1. Apply DC 12V power to the receiver.
  2. Press the learning button on the receiver. The receiver's LED indicator will turn ON.
  3. Press the 'ON' button on your remote transmitter once. The LED indicator on the receiver will flash once.
  4. Immediately press the 'OFF' button on your remote transmitter once. The LED indicator on the receiver will flash once again.
  5. Learning is now successful.

6.2 Clearing Codes

To clear all learned remote codes from the receiver:

  • Press and hold the learning button on the receiver.
  • Continue holding until the receiver's LED indicator flashes 7 times.
  • All previously learned codes are now cleared.

6.3 Changing Working Modes

The working mode is selected by the number of flashes of the receiver's LED indicator after pressing the learning button.

  1. Latched Mode (Flash 1 time):
    - Press the learning button until the LED flashes 1 time.
    - Operation: Press 'ON' on the remote to turn the relay ON. Press 'OFF' on the remote to turn the relay OFF.
  2. Momentary Mode (Flash 2 times):
    - Press the learning button until the LED flashes 2 times.
    - Operation: Press and hold 'ON' on the remote to turn the relay ON. Release 'ON' to turn the relay OFF.
  3. Toggle Mode (Flash 3 times):
    - Press the learning button until the LED flashes 3 times.
    - Operation: Press 'ON' on the remote to turn the relay ON. Press 'ON' again to turn the relay OFF.
  4. 10 Seconds Delay Mode (Flash 4 times):
    - Press the learning button until the LED flashes 4 times.
    - Operation: Press 'ON' on the remote to turn the relay ON. The relay will remain ON for 10 seconds, then automatically turn OFF.
  5. 60 Seconds Delay Mode (Flash 5 times):
    - Press the learning button until the LED flashes 5 times.
    - Operation: Press 'ON' on the remote to turn the relay ON. The relay will remain ON for 60 seconds, then automatically turn OFF.
  6. 300 Seconds Delay Mode (Flash 6 times):
    - Press the learning button until the LED flashes 6 times.
    - Operation: Press 'ON' on the remote to turn the relay ON. The relay will remain ON for 300 seconds, then automatically turn OFF.
Video 1: Demonstration of Remote Control Switch Working Modes and Pairing

7. Applications

This versatile remote control switch can be used in a variety of settings, including:

  • Controlling DC 12V lighting systems (e.g., LED strips, outdoor lights).
  • Operating DC 12V motors (e.g., garage door openers, small pumps).
  • Managing DC 12V fans or other small appliances.
  • Integration into low-voltage industrial control systems.
Typical Applications of the Remote Control Switch
Figure 7: Typical Applications of the Remote Control Switch

8. Troubleshooting

  • Device not responding to remote:
    - Check if the remote control's batteries (2x CR2016) are depleted and replace if necessary.
    - Ensure the remote is within the operating range (20-50 meters).
    - Re-pair the remote with the receiver using the learning method described in Section 6.1.
  • No power to the connected device:
    - Verify that the DC 12V input power to the receiver is correctly connected and active.
    - Check all wiring connections for looseness or incorrect polarity.
    - Ensure the connected load does not exceed the maximum power rating of 350W or current rating of 40A. Overloading can cause the relay to fail.
  • Relay clicks but device doesn't turn on:
    - This indicates the relay is switching, but there might be an issue with the load's wiring or the load itself. Check the load device's power and connections.
  • Inconsistent operation:
    - Clear all learned codes (Section 6.2) and re-pair the remote.

9. Maintenance

9.1 Remote Transmitter Battery Replacement

The remote transmitter uses two CR2016 button cell batteries. If the remote's range decreases or it stops responding, replace the batteries:

  1. Carefully open the remote control casing.
  2. Remove the old CR2016 batteries.
  3. Insert new CR2016 batteries, ensuring correct polarity.
  4. Close the remote control casing securely.

9.2 Cleaning

Wipe the receiver and transmitter with a dry, soft cloth. Do not use liquid cleaners or solvents.

10. User Tips

  • Simple Programming: Users have noted the programming is straightforward once understood. Refer to Section 6.1 for clear pairing steps.
  • Easy Installation: The unit is generally easy to install. Always double-check wiring for correct polarity and secure connections.
  • Universal Use: This switch is highly versatile and can be adapted for various DC 12V applications, from car accessories to home automation projects.
  • Power Considerations: While rated for 40A, the device itself is marked MAX 350W. For optimal performance and longevity, ensure your connected load does not exceed 350W.

11. Warranty and Support

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.