1. Introduction
Thank you for choosing the MagTool Aquarium Heating Rod. This device is designed to maintain a stable and optimal temperature in your aquarium, providing a comfortable and secure environment for your aquatic life. Featuring advanced safety measures like over-temperature protection and automatic power-off, along with an external controller for easy temperature adjustment, this heater is suitable for various aquarium types.

2. Product Components
The MagTool Aquarium Heating Rod consists of several key components designed for efficient and safe operation:
- Heater Shell: The protective outer casing.
- Heater Core (Dual Core): Contains the nickel-chromium heating wire for rapid and consistent heat transfer.
- Temperature Sensor: Built-in high-precision sensor for accurate temperature monitoring.
- External Controller: For setting and monitoring temperature, with an LED display.

3. Safety Information
Please read and understand all safety instructions before using this product. Failure to follow these instructions may result in product damage, injury, or electric shock.
- Over-Temperature Protection: The heater automatically stops heating once the set temperature is reached, preventing overheating.
- Water-Off Protection: An internal water level sensor cuts power when the heater is out of water, preventing dry heating and equipment damage.
- Controller Safety: The external controller is NOT waterproof. Do not submerge it in water.
- Cool-Down Period: If you need to remove the heater from the aquarium, always power it off and wait at least 5 minutes to allow the heating element to cool down before extraction. Removing it while hot may damage the heating core.
- Placement: Ensure the heater is fully submerged in water during operation. Do not bury the heater in sand or substrate.
- Material Safety: Crafted with thickened high-temperature-resistant quartz glass and explosion-proof quartz sand, effectively sealing against water infiltration. The external heater cover is made of high-quality PC plastic, safeguarding fish from direct contact with the heating element.
4. Setup
Follow these steps to properly set up your MagTool Aquarium Heating Rod:
- Unpack: Carefully remove all components from the packaging.
- Heater Placement: Position the heating rod in an area of your aquarium with strong water flow. This ensures rapid and efficient heat distribution throughout the tank. Use the provided rubber suction cups to securely affix the heating rod to the glass surface. Ensure the heater is fully submerged. Do not bury the heater in sand or substrate.
- Controller Placement: Place the external controller in a dry location where it is easily accessible for adjustments and monitoring. Use the hanging hook to fix the controller to the side of the aquarium or another suitable surface. Remember, the controller is not waterproof.
- Connect Power: Plug the heater's power cord into a suitable electrical outlet.



5. Operating Instructions
The external controller allows for precise temperature management and monitoring.

5.1. LED Display
- The LED display shows both the Current Temperature and the Set Temperature.
- HEAT (Red Indicator Light): When the red indicator light is on, it indicates that the current temperature is below the set value, and the heater is actively heating.
- KEEP (Blue Indicator Light): When the blue indicator light is on, it signifies that the current temperature is not below the set value, and the heater is not actively heating.
5.2. Temperature Adjustment
- Increase Temperature: Press the "+" button once to increase the set temperature by 1°F / 1°C.
- Decrease Temperature: Press the "-" button once to reduce the set temperature by 1°F / 1°C.
- The temperature can be set within a range of 59°F to 93°F (15°C to 34°C).
5.3. Changing Temperature Units (°C/°F)
- To switch between Fahrenheit (°F) and Celsius (°C), press and hold both the "+" and "-" buttons simultaneously for 5 seconds. The display unit will change accordingly.
5.4. Power Failure Memory
The MagTool Aquarium Heater features a power failure memory function. In the event of a power outage, the heater will retain your last temperature setting and resume operation at that setting once power is restored, eliminating the need for manual readjustment.
6. Maintenance
Proper maintenance ensures the longevity and optimal performance of your aquarium heater.
- Cleaning: Regularly inspect the heating rod for algae or mineral buildup. If cleaning is necessary, always unplug the heater and allow it to cool for at least 5 minutes before removing it from the water. Use a soft cloth or brush to gently clean the surface. Do not use harsh chemicals or abrasive materials.
- Inspection: Periodically check the power cord and heater casing for any signs of damage, cracks, or wear. If any damage is observed, discontinue use immediately and contact customer support.
- Water Changes: During water changes, ensure the heater remains submerged or is powered off and allowed to cool before water levels drop below the minimum immersion line.
7. Troubleshooting
If you encounter issues with your MagTool Aquarium Heating Rod, refer to the following common problems and solutions:
- Heater Not Heating (Red Indicator Off, Blue Indicator On): This indicates the aquarium temperature has reached or exceeded the set temperature. The heater will automatically stop heating. If the water is too cold, check the set temperature and increase it if necessary.
- Heater Not Heating (No Indicators On): Check if the heater is properly plugged into a working power outlet. Ensure the power supply is active.
- Overheating: The heater is equipped with over-temperature protection. If the water temperature significantly exceeds the set temperature, the heater should automatically power off. If you suspect overheating, unplug the unit immediately and check the set temperature.
- Water-Off Protection Activated: If the water level drops below the heater's minimum immersion line, the water-off protection will activate, and the heater will stop functioning. Ensure the heater is fully submerged.
- Temperature Display Inaccurate: Ensure the temperature sensor is clean and free from debris. If the issue persists, contact customer support.
8. Specifications
Detailed specifications for the MagTool Aquarium Heating Rod:

| Feature | Description |
|---|---|
| Power Options | 100W, 200W, 300W, 500W, 800W, 1000W, 1200W |
| Application (Gallons) | 100W: 13-31 Gal 200W: 26-62 Gal 300W: 39-94 Gal 500W: 65-156 Gal 800W: 104-250 Gal 1000W: 130-312 Gal 1200W: 156-374 Gal |
| Application (Liters) | 100W: 50-120 L 200W: 100-240 L 300W: 150-360 L 500W: 250-600 L 800W: 400-960 L 1000W: 500-1200 L 1200W: 600-1440 L |
| Heating Element Quantity | 1 (for 100W-500W), 2 (for 800W-1200W) |
| Temperature Accuracy | ±1°F / ±1°C |
| Control Range | 59-93°F / 15-34°C |
| Heating Element | Nickel-chromium heating wire |
| Heater Material | Thickened high-temperature-resistant quartz glass, explosion-proof quartz sand |
| External Cover Material | High-quality PC plastic |
| Dimensions (800-1200W) | Length: 29.5 cm (11.61 inches) Width: 8 cm (3.15 inches) Depth: 3 cm (1.18 inches) |
| Dimensions (100-500W) | Length: 27.5 cm (10.82 inches) Width: 6 cm (2.36 inches) Depth: 2.5 cm (0.98 inches) |
9. User Tips
Here are some helpful tips for using your MagTool Aquarium Heating Rod:
- Choosing the Right Wattage: To select the appropriate wattage for your heater, a general guideline is to multiply the volume of your tank in liters by a factor between 0.8 and 2.5. For optimal performance, we recommend using a factor of approximately 2. For example, for a 200-liter tank, a 400W heater would be suitable (200 L * 2 = 400W).
- Optimal Placement: Always place the aquarium heater in an area with strong water flow, such as near the outlet of a filter or in a sump's water pump chamber. This ensures even heat distribution and prevents cold spots.
- Avoid Burying: Never bury the heater in sand or substrate, as this can impede heat dissipation and potentially damage the unit.
- Safe Removal: When performing maintenance or removing the heater, always power it off and wait for at least 5 minutes to allow the heating element to cool down completely. This prevents damage to the heating core from sudden temperature changes.
- Protect the Controller: The external controller is not waterproof. Keep it away from water splashes and ensure it is placed in a dry location.
10. Warranty and Support
The MagTool Aquarium Heating Rod comes with a 12-month quality guarantee from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use.
For warranty claims, technical support, or any questions regarding your product, please contact the seller or manufacturer directly through your purchase platform. Please have your purchase details and product model information ready when contacting support.