G-NiceRF DMR858S-V

Contents

G-NiceRF DMR TIER II DMR858S-V Digital Walkie Talkie Module

Model: DMR858S-V | Brand: G-NiceRF

1. Introduction

The DMR858S is an all-in-one 5W professional digital walkie talkie module, integrating both analog and DMR Tier II walkie talkie functionalities. This module is designed for ease of use, featuring an embedded DSP processor, DMR encoder/decoder, RF/Audio Amplifier, PTT, Microphone, 16 Channel switch, and Volume adjustment all on board. By simply connecting a power supply and a speaker, it forms a complete 5W professional DMR walkie talkie system.

The DMR858S offers long-range communication and high-quality voice transmission. Special heat sinks are incorporated to ensure stable performance during extended operation. In DMR mode, the digital intercom supports advanced features including:

  • SMS sending function, supporting both pass-through and SMS application.
  • Voice encryption function.
  • SMS encryption function.
  • Calling and called prompts.

2. Key Features

  • Frequency Bands:
    • UHF band: 400~470 MHz
    • VHF band: 134~174 MHz
    • 350 band: 320-400 MHz (three frequency bands are optional)
  • Communication Range: 6~8 Km in open areas.
  • Power Output: Maximum 5W, Low power 1W.
  • Sensitivity: Up to -120dBm.
  • Bit Error Rate (BER): Less than 2% BER @ -117dBm.
  • Frequency Configuration: TX/RX frequency can be set separately.
  • Bandwidth: Analog: 12.5 / 25 KHz; DMR: 6.25KHz.
  • Modes: Supports both DMR and Analog walkie talkie modes.
  • Messaging: SMS transmission and reception.
  • Memory: Built-in EEPROM for data saving even when powered off.
  • Power Efficiency: Low power consumption in sleep mode.
  • DMR Standard: DMR Tier II compliant.
  • Audio Quality: Automatic tail sound elimination.
  • Design: Embedded design suitable for handheld products.

3. Applications

The DMR858S-V module is suitable for a variety of applications, including:

  • Small professional walkie talkies
  • Invisible intercom systems
  • Building community security systems
  • Sporting goods and equipment
  • Handheld and pocketable communication devices
  • Audio surveillance systems

4. Technical Specifications

4.1 General Parameters

Table of General Parameters for DMR858S-V module, including power supply, working temperature, frequency range, serial baud rate, and current consumption.

Table: General Parameters for DMR858S-V module.

4.2 Analog RX Parameters

Table of Analog Receiver Parameters for DMR858S-V module, including sensitivity, selectivity, and audio output characteristics.

Table: Analog Receiver Parameters.

4.3 DMR RX Parameters

Table of DMR Receiver Parameters for DMR858S-V module, including BER, selectivity, and blocking immunity.

Table: DMR Receiver Parameters.

4.4 Analog TX Parameters

Table of Analog Transmitter Parameters for DMR858S-V module, including frequency deviation, sensitivity, and audio distortion.

Table: Analog Transmitter Parameters.

4.5 DMR TX Parameters

Table of DMR Transmitter Parameters for DMR858S-V module, including frequency error and output power characteristics.

Table: DMR Transmitter Parameters.

4.6 Block Diagrams

Block diagram of the DMR858S module, showing antenna, PA, LNA, RX match, baseband chip, and various interfaces.

Figure: DMR858S Module Block Diagram.

Block diagram of the DMR858S-PJ control board, showing LDO, audio PA, MCU, encoder, and various interfaces.

Figure: DMR858S-PJ Control Board Block Diagram.

4.7 Mechanical Dimensions

Mechanical dimensions of the DMR858S module, top view with measurements.

Figure: DMR858S Module Top View Dimensions (59.10 x 24.10 mm).

Mechanical dimensions of the DMR858S module, side view with height measurement.

Figure: DMR858S Module Side View Dimensions (Height: 12.68 mm).

Mechanical dimensions of the DMR858S-PJ control board, top and side views with measurements.

Figure: DMR858S-PJ Control Board Dimensions (37.60 x 24.20 x 8.0 mm).

5. Setup and Configuration

5.1 Module Connection

The DMR858S module can be connected to a control board (DMR858S-PJ) via an FPC cable. The system connection diagram illustrates this:

System connection diagram showing DMR858S module connected to DMR858S-PJ control board with power and speaker connections.

Figure: System Connection Diagram (DMR858S and DMR858S-PJ).

5.2 Pin Definitions

Understanding the pin definitions is crucial for proper integration and operation.

Table of pin definitions for the DMR858S Functional Board, including GND, MIC_IN, UART-RX/TX, CS, PTT, LINE_OUT, T/R, SPKEN, and VCC.

Table: Pin Definitions for DMR858S Functional Board.

Table of pin definitions for the DMR858S-PJ Control Board, including VCC, GND, CS, PTT, LINE_OUT, frequency channel selection, SPKN/SPKP, SET, MIC_IN, TXD/RXD, 3.3V output, SPKEN, NC, H/L, and Ground.

Table: Pin Definitions for DMR858S-PJ Control Board.

5.3 Antenna Connection

An antenna is a critical component for the communication system. The module requires an antenna with an impedance of 50 Ohm. Common antenna types include rubber straight antennas, sucker antennas, and telescopic antennas. Select an antenna appropriate for your application environment. For optimal performance, it is recommended to use antennas designed for this module.

5.4 PC Software Configuration

The DMR858S Module provides a standard serial port for configuration. Users can configure and read parameters by sending serial instructions. The module has built-in memory to save all configured parameters even after power-off. PC software is available to facilitate configuration. The DMR858S can be connected to a computer via a specialized USB cable or UART interface.

Diagram showing the Walkie Talkie Module TTL Interface, connecting the DMR828 module to a computer via USB cable for software configuration.

Figure: Walkie Talkie Module TTL Interface Diagram.

  1. Install the USB Driver and PC software on your computer.
  2. Connect the DMR858S module with your computer via a specialized USB cable.
  3. The module will enter setting mode, as shown in the diagram.

6. Operating Instructions

6.1 Channel Selection

The DMR858S has 16 default channels: CH0~CH7 operate in DMR mode, and CH8~CHF operate in analog mode. Frequency channel selection can be performed using the onboard rotary switch or by providing input to specific pads. To control the channel via pads, turn the rotary switch to channel 0 or remove it.

The channel selection uses 8421 encoding for 16 channels (0-15):

  • Pin 7 (4 bits): 8 (maximum bit), 4 (3rd bit), 2 (2nd bit), 1 (least bit).
  • Example: 0000 = channel 0, 0001 = channel 1, 0010 = channel 2, 0011 = channel 3, ..., 1111 = channel 15.

6.2 Setting Mode

The module features a 'SET' pin (Pin 15 on DMR858S-PJ) to switch between setting mode and normal mode:

  • 0: Setting Mode - Allows configuration of parameters via serial interface.
  • 1: Normal Mode - Standard operation mode for communication.

6.3 Output Power Control

The output power can be controlled via the 'H/L' pin (Pin 23 on DMR858S-PJ):

  • 0: Low Power
  • 1: High Power

6.4 Functional Board Overview

Diagram of the DMR Functional Board with labels for SMA antenna, 18Pin FPC, Working/Set mode switch, Mic, USB, Slide Switch (H/L output power, normal/test mode), Channel rotary switch, and PTT Key.

Figure: DMR Functional Board with key components labeled.

7. Maintenance

To ensure the longevity and optimal performance of your DMR858S-V module, follow these general maintenance guidelines:

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to extreme temperatures or humidity.
  • Ensure proper ventilation, especially if operating at high power for extended periods, to prevent overheating.
  • Handle the module with care to prevent physical damage to components or connectors.
  • Regularly check all connections (power, antenna, FPC cable) to ensure they are secure.

8. Troubleshooting

This section provides general troubleshooting tips. For specific issues, refer to the detailed technical documentation or contact support.

  • No Power: Verify power supply connections and ensure the voltage is within the specified range (3.6-8.4V).
  • No Communication: Check antenna connection and ensure it has 50 Ohm impedance. Verify frequency settings and ensure both modules are on the same channel and mode (DMR/Analog). Confirm correct pin connections for UART, PTT, and audio.
  • Poor Audio Quality: Check speaker and microphone connections. Ensure the SPKEN pin is correctly configured to drive external audio amplifiers if used. Verify signal strength and reduce interference sources.
  • Configuration Issues: Ensure the module is in 'Setting Mode' (SET pin = 0) when attempting to configure via serial commands or PC software. Verify USB driver installation and correct cable connection.
  • Limited Range: Ensure the antenna is properly installed and unobstructed. Check for environmental factors that might interfere with signal propagation. Verify output power setting (High/Low).

9. User Tips

While no specific user reviews or Q&A were provided, here are some general tips for working with the DMR858S-V module:

  • Software Configuration: Utilize the provided PC software for easier and more precise configuration of channels, frequencies, and other parameters. This can be more convenient than manual serial commands.
  • Antenna Matching: Always use a well-matched 50 Ohm antenna for optimal range and signal integrity. A poorly matched antenna can reduce performance and potentially damage the module.
  • Heat Management: Although special heat sinks are designed, ensure adequate airflow around the module, especially in enclosed applications, to prevent thermal throttling during continuous transmission.
  • Pinout Verification: Double-check all pin connections against the provided pin definition tables before powering on to avoid damage.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official G-NiceRF website or contact your authorized distributor. Keep your purchase records for warranty claims. Specific warranty terms and conditions may vary by region and seller.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.