HGLRC Petrel 85Whoop

Contents

HGLRC Petrel 85Whoop FPV Tinywhoop Instruction Manual

Beginner's Entry into Light Flying

1. Introduction

The HGLRC Petrel 85Whoop is a four-axis 2S brushless motor FPV tinywhoop designed for beginners, suitable for both indoor and outdoor light flying. It features an integrated flight control system, a high-quality camera, and powerful motors for a smooth flight experience.

HGLRC Petrel 85Whoop FPV Tinywhoop
The HGLRC Petrel 85Whoop FPV Tinywhoop.

2. Product Overview and Components

The Petrel 85Whoop integrates several key components into a compact design, making it an excellent choice for new FPV pilots.

Key Features:

  • Integrated Flight Control: New SPECTER 10A 5-in-1 integrated flight control system, combining 4-way ESC, flight control, image transmission, and ELRS receiver.
  • High-Quality Camera: Equipped with a RunCam Nano4 lens for clear and sharp video.
  • Powerful Motors: Features SPECTER 1202.5-11000KV brushless motors.
  • Efficient Propellers: Utilizes Gemfan 1610 two-blade propellers for smooth flight.
  • Lightweight Design: Approximately 50g, offering agile performance.
  • Easy Motor Replacement: In-line motor design for convenient maintenance without soldering.
  • Receiver Options: Onboard SPI ELRS3.0 receiver (optional) with built-in antenna, or external TBS Nano receiver with a customized miniature T-shaped antenna.

Shipping List:

  • 1x Petrel 85Whoop drone
  • 8x Gemfan2015 two-bladed propellers
  • 1x Accessory pack (includes screwdriver, battery straps, rubber bands, propeller removal tool, stickers, and propeller direction diagram)
HGLRC Petrel 85Whoop package contents
Contents of the HGLRC Petrel 85Whoop package, including the drone, propellers, and accessory pack.

3. Specifications

ComponentSpecification
FramePetrel 85Whoop Frame
Flight ControllerSPECTER 10A AIO (MCU: STM32F411, GYRO: ICM42688)
Built-in ReceiverSPI ExpressLRS 2.4G (ELRS version) or external TBS Nano receiver (TBS version)
Built-in Image Transmission (VTX)0-RCE-25-100-400mW (adjustable), up to 48CH
Onboard ESCContinuous Current: 10A, Peak Current: 13A (10s)
ESC ProtocolDshot600, Oneshot, Multishot
ESC FirmwareZ_H_30 (Bluejay)
Flight Control FirmwareHGLRCF411SX1280 V2
Input Voltage1S-2S 3.7V-7.4V (Lipo)
Mounting Hole25.5x25.5mm.M2
MotorSPECTER 1202.5-11000KV Brushless Motor
PropellerGemfan 2015 Two-Blade Propeller
Weight (ELRS Version)48±1g
Weight (TBS Version)50±1g
Recommended Battery2S 450mAh-550mAh high-voltage battery, XT30 plug
CameraRunCam Nano4 (1/3" CMOS, 800TVL, 2.1mm (M8) FOV 160°, NTSC/PAL switchable)
MaterialComposite Material
Recommended Age14+ years
Detailed specifications and diagrams for HGLRC Petrel 85Whoop
Detailed specifications, wiring diagrams, and binding instructions for the Petrel 85Whoop components.

4. Setup and Installation

4.1 Propeller Installation

Ensure propellers are installed correctly according to the rotation direction. Incorrect installation will prevent the drone from flying properly.

  1. Identify the correct propeller for each motor based on its rotation direction (Clockwise - CW or Counter-Clockwise - CCW).
  2. Align the propeller with the motor shaft and press firmly until it is securely seated.
Propeller direction diagram
Propeller direction diagram: Front Left (1) and Rear Right (3) are CW, Front Right (2) and Rear Left (4) are CCW.

4.2 Receiver Binding

Binding your receiver to your radio transmitter is crucial for controlling the drone. Follow the instructions specific to your receiver type.

For ELRS 2.4G Receiver:

  1. Power on and off the drone three times in quick succession.
  2. The LED on the receiver should flash twice quickly, indicating it is in binding mode.
  3. Initiate the binding process on your ELRS radio transmitter.
  4. Once bound, the receiver LED will turn solid, indicating a successful connection.

For TBS Nano Receiver:

  1. Connect the drone to Betaflight Configurator on your computer.
  2. Navigate to the 'Receiver' tab and set the Receiver Mode to 'Serial-based receiver' and the Provider to 'CRSF'.
  3. Connect the TBS Nano receiver to the Flight Controller (FC) as per the wiring diagram (refer to the detailed specifications image).
  4. Press and hold the bind button on the TBS Nano receiver.
  5. Power on the drone.
  6. Initiate the binding process on your TBS radio transmitter.
  7. Once bound, the receiver LED will turn solid, indicating a successful connection.

4.3 Battery Connection

The drone uses an XT30 plug for battery connection. Ensure you use a compatible 2S (3.7V-7.4V) LiPo battery with a capacity between 450mAh and 550mAh.

  1. Carefully connect the XT30 battery plug to the drone's XT30 connector.
  2. Ensure the connection is secure before flight.
HGLRC Petrel 85Whoop with battery connected
The Petrel 85Whoop with a battery connected, ready for flight.

5. Operating Instructions

5.1 Pre-Flight Checklist

  • Ensure the battery is fully charged and securely connected.
  • Verify all propellers are correctly installed and free from damage.
  • Confirm the receiver is successfully bound to your radio transmitter.
  • Check for any loose wires or components.
  • Perform a quick visual inspection of the drone for any physical damage.

5.2 First Flight

  1. Place the drone on a flat, level surface.
  2. Arm the motors using your radio transmitter (typically by moving the throttle stick to the bottom right or left, depending on your Betaflight configuration).
  3. Slowly increase the throttle to lift off.
  4. Practice gentle movements to get accustomed to the drone's controls.
  5. Monitor battery voltage and land safely when the voltage drops to a critical level (e.g., around 3.5V per cell for LiPo). A single battery typically provides about 5 minutes of flight time.

5.3 Video Transmitter (VTX) Operation

The onboard 400mW analog VTX supports up to 48 channels across multiple bands (A, B, E, F, R) and adjustable power output (25mW, 100mW, 400mW). Refer to the VTX frequency table in the detailed specifications image for channel and frequency details. Adjust VTX settings via Betaflight OSD or your radio transmitter if configured.

6. Maintenance

  • Propellers: Regularly inspect propellers for cracks, bends, or chips. Replace damaged propellers immediately to ensure stable flight.
  • Motors: Check motors for any debris (e.g., hair, grass) wrapped around the shafts. The in-line motor design allows for easier replacement if a motor fails.
  • Frame: Inspect the frame for any cracks or damage after crashes.
  • Electronics: Keep the flight controller and other electronic components clean and free from dust or moisture.
  • Battery: Store LiPo batteries safely and charge them using a compatible LiPo charger. Do not overcharge or over-discharge.

7. Troubleshooting

7.1 ELRS Receiver Frequency Issues

If you are using an ELRS TX module and cannot achieve a stable frequency connection, please note the following:

  • The SPI ELRS receiver does not support D (D250, D500), F (F500, F1000), or Full Res (100Hz Full Res, 333Hz Full Res) packet rates.
  • When using an ELRS TX module, set the Tx module's PacketRate option to a range between 50HZ-500HZ.
  • Avoid setting modes starting with D/F.

7.2 Drone Not Arming

  • Ensure your radio transmitter is powered on and connected to the drone.
  • Check if the receiver is properly bound (solid LED).
  • Verify that the arming switch/stick command is correctly configured in Betaflight.
  • Check for any error messages in the Betaflight OSD or Configurator (e.g., low battery, accelerometer calibration needed).

7.3 Unstable Flight

  • Inspect propellers for damage or incorrect installation.
  • Ensure motors are clean and spinning freely.
  • Check for loose components or frame damage.
  • Recalibrate the accelerometer in Betaflight.

8. User Tips

8.1 Compatible Accessories

For the best FPV experience, ensure compatibility when selecting your remote control and FPV video headset. The Petrel 85Whoop supports ELRS 2.4G and TBS Nano receivers, so choose a radio transmitter that supports these protocols. For FPV goggles, any analog FPV goggles compatible with the 5.8GHz frequency band will work with the drone's VTX.

8.2 Battery Management

Always use the recommended 2S 450mAh-550mAh high-voltage batteries with an XT30 connector. Proper battery care, including balanced charging and not over-discharging, will extend battery life and ensure safe operation.

9. Warranty and Support

For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2023 HGLRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.