SHIMANO R8170

Contents

Shimano Ultegra R8170 Di2 Electronic Groupset User Manual

Model: R8170 | Brand: SHIMANO

1. Introduction

This manual provides essential information for the safe and effective use of your Shimano Ultegra R8170 Di2 Electronic Groupset. It covers the installation, operation, maintenance, and specifications of the components, including the R8150 Rear Derailleur, R8100 Cassette, and Hydraulic Disc Brakes. Please read this manual thoroughly before attempting any installation or operation.

2. Safety Information

▲ Warning Symbol & Notice

Warning:

  • This product is not a toy and is not suitable for children under 16 years old without adult supervision. Keep all small parts (e.g., screws, pulleys) away from infants and toddlers to avoid choking hazards.
  • Always wear appropriate protective gear (helmet, gloves, knee pads) when operating the bicycle with this derailleur. Do not use the product in traffic without proper training.
  • Ensure the derailleur is correctly installed and adjusted before use. Improper installation may cause chain slippage, leading to falls or serious injury.
  • Do not modify the derailleur's structure or components. Unauthorized modifications void compliance and safety guarantees.
  • This product is not intended for use with children's bicycles (refer to EN 14765 for children-specific requirements).
  • Keep the derailleur away from corrosive substances (acids, solvents) and extreme temperatures to prevent mechanical failure.

Additional Safety Notes:

  • Regularly inspect the derailleur for wear, damage, or loose connections. Replace worn parts immediately using genuine Shimano accessories.

Applicable Regulations & Harmonized Standards

This product complies with the following EU regulations and standards:

  • General Product Safety Directive (GPSD): 2001/95/EC
  • Mechanical Directive (MD): 2006/42/EC

Harmonized Standards:

  • EN ISO 4210-2:2015 (Bicycle safety requirements for city, trekking, mountain bikes)
  • EN 14781:2015 (Racing bicycle specific safety standards)
  • REACH Regulation (EC) No 1907/2006 (Restriction of hazardous substances)

Usage Restrictions

Not Suitable For:

  • Children under 16 years old (without adult supervision)
  • Bicycles with wheel sizes below 26" or above 29"
  • Electric bicycles with motor power exceeding 250W
  • Off-road use in extreme conditions (e.g., rock climbing, steep descents >30°)
  • Environmental Restrictions: Do not use in saltwater environments (e.g., coastal areas) without proper corrosion protection.

3. Package Contents

Your Shimano Ultegra R8170 Di2 Electronic Groupset package includes the following components:

Shimano Ultegra R8170 Di2 Electronic Groupset components
Overview of the Shimano Ultegra R8170 Di2 Electronic Groupset components.
  • ULTEGRA CS-R8100 Cassette (11-30T or 11-34T, depending on selection) 12-Speed
  • XT CN-M1800 12-Speed Chain
  • ULTEGRA ST+BR-R8170 Di2 2x12-Speed Shifter Brake Set
  • ULTEGRA FD-R8150 Di2 2x12-speed Front Derailleur Braze On
  • ULTEGRA RD-R8150 Di2 12-speed Rear Derailleur
  • Di2 Battery BT-DN300 (For built-in installation in the seat post)
  • Di2 Battery Charging Cable EW-EC300
Shimano Ultegra R8170 Di2 Groupset components (without crankset) with 11-34T cassette
R8170 Groupset components (without crankset) with 11-34T cassette option.
Shimano Ultegra R8170 Di2 Groupset components (without crankset) with 11-30T cassette
R8170 Groupset components (without crankset) with 11-30T cassette option.

4. Specifications

AttributeValue
Brand NameSHIMANO
Model NumberR8170
Derailleur Groupset TypeElectronic Derailleur system
Gears24 Speed
TypeFront Derailleur
ComponentsDerailleurs
OriginJapan
High-concerned chemicalNone

Component Weights

  • Front Derailleur (FD-R8150): Approximately 110.8g
  • Rear Derailleur (RD-R8150): Approximately 259.8g
  • Di2 Battery Charging Cable (EW-EC300): Approximately 68.9g
Weight of Shimano Ultegra FD-R8150 Front Derailleur
Weight measurement of the FD-R8150 Front Derailleur (110.8g).
Weight of Shimano Ultegra RD-R8150 Rear Derailleur
Weight measurement of the RD-R8150 Rear Derailleur (259.8g).
Weight of Shimano Di2 EW-EC300 Charging Cable
Weight measurement of the EW-EC300 Charging Cable (68.9g).

5. Setup and Installation

Proper installation is crucial for the performance and safety of your electronic groupset. It is highly recommended that installation be performed by a qualified bicycle mechanic. For detailed, step-by-step instructions, please refer to the official Shimano dealer manuals or the PDF user manual referenced below.

General Installation Overview:

  1. Shifter Brake Set (ST+BR-R8170): Install the hydraulic shifter/brake levers onto your handlebars. Ensure proper routing of hydraulic lines and electrical wires. The hydraulic lines are pre-filled with oil.
  2. Front Derailleur (FD-R8150): Mount the front derailleur to the braze-on tab on your bike frame. Connect the electrical wire.
  3. Rear Derailleur (RD-R8150): Mount the rear derailleur to the derailleur hanger. Connect the electrical wire.
  4. Cassette (CS-R8100): Install the cassette onto your freehub body. Ensure it is tightened to the manufacturer's specifications.
  5. Chain (CN-M1800): Install the chain, ensuring correct length and proper connection with the master link.
  6. Di2 Battery (BT-DN300): Install the battery into the seat post or designated internal frame location. Connect the necessary electrical wires.
  7. Wiring and Connections: Connect all Di2 components using the appropriate EW-SD300 wires. Ensure all connections are secure and properly routed internally or externally as per your frame design.
  8. System Initialization and Adjustment: After physical installation, use the Shimano E-Tube Project app to initialize the system, perform firmware updates, and fine-tune shifting adjustments.
Shimano Ultegra ST-R8170 Shifter and BR-R8170 Hydraulic Brake Caliper
ST-R8170 Shifter and BR-R8170 Hydraulic Brake Caliper.
Shimano Ultegra FD-R8150 Front Derailleur
FD-R8150 Front Derailleur.
Shimano Ultegra RD-R8150 Rear Derailleur
RD-R8150 Rear Derailleur.
Shimano Ultegra CS-R8100 11-34T Cassette
CS-R8100 11-34T Cassette.
Shimano Di2 BT-DN300 Battery
BT-DN300 Battery for Di2 system.
Shimano Di2 EW-EC300 Charging Cable
EW-EC300 Charging Cable.

For comprehensive installation details, please consult the official Shimano technical documentation or the PDF user manual available at: Shimano Ultegra R8170 Di2 User Manual (PDF).

6. Operating Instructions

Electronic Shifting (Di2)

The Di2 system offers precise and effortless gear changes. Use the buttons on the ST-R8170 shifters to shift gears. Typically, one button shifts to a larger cog/chainring, and the other shifts to a smaller cog/chainring. The system can be customized via the E-Tube Project app for synchronized shifting modes.

Hydraulic Disc Brakes

The BR-R8170 hydraulic disc brakes provide powerful and consistent stopping power. Squeeze the brake levers to engage the brakes. Ensure proper bedding-in of new brake pads and rotors for optimal performance. Avoid sudden, hard braking unless necessary.

Battery Charging

The BT-DN300 battery powers the Di2 system. Use the EW-EC300 charging cable to charge the battery. Connect the cable to the charging port (usually on the rear derailleur or a junction box) and a USB power source. The battery status can be checked via the E-Tube Project app or indicator lights on the system.

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your Shimano Ultegra Di2 groupset.

  • Cleaning: Keep all components clean, especially the chain, cassette, and derailleurs. Use appropriate bicycle cleaning products.
  • Lubrication: Regularly lubricate the chain with a suitable bicycle chain lubricant.
  • Inspection: Inspect the derailleur for wear, damage, or loose connections. Check brake pads for wear and hydraulic lines for leaks.
  • Firmware Updates: Periodically check for and install firmware updates for your Di2 components using the E-Tube Project app to ensure the latest features and performance enhancements.
  • Maintenance Interval: Inspect and lubricate the derailleur every 500km or every 3 months, whichever comes first.

8. Troubleshooting

If you encounter issues with your Di2 groupset, consider the following common troubleshooting steps:

  • Shifting Issues: If shifting is inconsistent or unresponsive, check the battery charge level. Ensure all electrical connections are secure. Use the E-Tube Project app to check for errors, perform adjustments, and update firmware.
  • Brake Performance: If brakes feel spongy or lack power, they may need bleeding. Check for worn brake pads or contaminated rotors. Consult a professional mechanic for hydraulic brake service.
  • System Not Responding: Check the battery connection and charge. Ensure all wires are properly seated. A system reset might be necessary (refer to the full manual).

9. User Tips

  • Professional Installation: While the groupset can be installed by experienced users, professional installation is recommended to ensure correct setup and optimal performance, especially for hydraulic brakes and electronic wiring.
  • E-Tube App: Utilize the Shimano E-Tube Project app for firmware updates and fine-tuning. This can resolve many minor issues and unlock full customization.
  • Hydraulic Line Fittings: Be aware that additional fittings for hydraulic lines (like olives) might be needed and may not be included in all kits. Plan accordingly.
  • Packaging: Components may arrive without original retail packaging, but are typically genuine Shimano products. Verify authenticity using serial numbers and the E-Tube app.

10. Warranty and Support

EU Declaration of Conformity (DoC)

This product (Shimano Bicycle Derailleur, Model: Universal Fit for Road/Gravel/MTB/E-Bike) meets the essential requirements of EU Directive 2006/42/EC (Mechanical Directive) and related harmonized standards. The EU Authorized Representative is responsible for ensuring compliance with EU market surveillance requirements. A complete copy of the DoC is available upon request from the EU Responsible Person.

Manufacturer Information

EU Responsible Person (Authorized Representative)

  • Name: MJCM SARL
  • Country: France
  • Address: 78 avenue des Champs Elysees, Bureau 326, 75008 Paris, France
  • Phone: +33-752907452
  • Email: mjcm190928@gmail.com

© 2023 Shimano Inc. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.