BAOFENG BF-T20

Contents

Baofeng BF-T20 Mini Walkie Talkie User Manual

Your guide to operating and maintaining your Baofeng BF-T20 Two-Way Radio.

Video: A 360-degree view of the Baofeng BF-T20 Mini Walkie Talkie, showcasing its compact design and various angles.

1. Introduction

Thank you for purchasing the Baofeng BF-T20 Mini Vehicle Two-Way Transceiver. This compact and portable radio is designed for reliable communication in various settings. Please read this manual carefully before use to ensure proper operation and to maximize the performance of your device.

Functions and Features

  • Broadcast FM radio receiver (65-108MHz)
  • Alarm and built-in LED flashlight
  • Max 20 channels
  • Time count down (0.5hr/1hr/.../8hrs)
  • Voice prompt
  • VOX (voice activated transmission)
  • 50 CTCSS tone/104 DCS code/nonstandard tone available
  • Tail tone elimination
  • Battery saving function
  • Width/Narrow band selection
  • SOS call notice
  • PC programmable

2. Getting Started

Before Proceeding

  • Qualified technicians shall service this equipment only. Do not modify the radio for any reason.
  • Use only BAOFENG supplied or approved accessories.
  • Turn off your radio prior to entering any area with explosive and flammable materials. Do NOT USE your transceiver at a gas/fuel station.
  • Do not expose the radio to direct sunlight over a long time, nor place it close to a heating source.
  • To avoid electromagnetic interference or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
  • Do not transmit for long periods of time, as it may overheat the transceiver.
  • Keep the unit away from dusty, damp and wet environments.

Unpacking and Inspecting

Please check the packaging of your radio for any signs of damage. Carefully open the box, and confirm you have received all the items listed below. If any items are damaged or missing, immediately contact your dealer.

What's in the Box

Contents of the Baofeng BF-T20 package including radio, battery, USB cable, hand strap, belt clip, and user manual.

Image: The standard package includes the Mini handheld radio, Hand strap, USB charging cable, and User manual.

  • Mini handheld radio
  • Battery Pack
  • Belt Clip
  • USB Charging Cable
  • Hand Strap
  • User Manual

Assembly

Battery Installation

Open the battery cover with a screwdriver. Join the electric lead into the socket of the battery. You will hear the voice 'welcome' and the channel number will be reported. Align the electric lead into the slot and place the battery smoothly, then screw the cover. To remove the battery, reverse these steps.

Belt Clip Installation

At the back of the radio, there are two parallel screws mounted. Remove these and thread them through the holes on the belt clip as you screw them back into the radio body.

Earpiece Connection

Open the cover of the earpiece jack, align the connector, and push it fully in.

3. Controls and Display

Getting to Know Your Radio

Diagram of Baofeng BF-T20 showing ON/OFF button, LED Flashlight, Antenna, Lanyard loop, Battery, PTT button, Speaker and Microphone, SOS button, Status LED, Keypad, Accessory jack, and Belt clip.

Image: Labeled diagram of the Baofeng BF-T20 highlighting its external components.

The Main Display

The transceiver features a seven-character segment code alphanumeric LCD, with auxiliary icons for various features.

IconDescriptionIconDescription
FMenu 9. Repeater function settingWTime countdown setting
88Memory channelOnWideband enabled
CTCTCSS enabledKeypad locked enabled
DCSDCS enabledBattery level indicator
FMBroadcast FMThe extension synchronizes the base
SOSEmergency call, pressing SOS buttonVolume indicator

Status LED

The status LED indicates the radio's activity: green when receiving a signal, red when transmitting, and off in standby.

SOS Button

The SOS button can be used for group calls or emergency calls. Pressing this button will transmit your call to all other radios.

Keypad Zone

The keypad includes the MENU key, which is used to enter and confirm menu options. Press and hold MENU to lock all keys except ON/OFF, SOS, and PTT.

Up and Down Keys

These keys are used to navigate through menus, select channels, and adjust volume.

FM (Broadcast FM and Alarm) Key

Press momentarily to start/stop the broadcast FM receiver. If a signal is received on the active channel while listening to FM, the receiver will open squelch to that frequency and remain there until the signal goes away, then switch back to FM. Press and hold to activate the alarm function.

MONI/VOL Key

Press momentarily to display the volume indicator, then use arrow keys to adjust. Press and hold to monitor the signal, opening the squelch to listen to unfiltered signals.

Lamp/Scan Key

Press momentarily to turn on/off the LED flashlight (a second press makes it flash). Press and hold to enable/disable the scanner.

Combination Key Functions

  • High and Low Output Power Switching: Press and hold the ON/OFF + LAMP keys for about two seconds to switch the radio on. You can then select high or low output power.
  • Resets the Radio to Factory Defaults: Press and hold the ON/OFF + MONI/VOL keys to switch on the radio. All settings will be reset to factory defaults (400.025MHz, no CTCSS/DCS, low output power, battery save, volume level 5, width band, SQL 5, key tone ON, other settings off).

4. Basic Operation

Power and Volume

Turning the Unit On

Press the On/Off button until you hear a "click". An audible beep and LCD display will confirm power-on. If voice prompt is enabled, it will announce "welcome to use".

Turning the Unit Off

Press and hold the On/Off button until the unit turns off.

Adjusting the Volume

Press the MONI/VOL key momentarily to display the volume indicator. Use the UP/DOWN arrow keys to adjust the volume level, then press MONI/VOL to confirm.

Making a Call

Press and hold the PTT button on the side of the radio body to transmit. Speak approximately 3-5cm from the microphone. Release the PTT to return to receive mode.

Working the Menu System

To navigate the menu:

  1. Press the MENU key to enter the menu.
  2. Use the arrow keys to navigate between menu items.
  3. Once you find the desired menu item, press MENU again to select it.
  4. Use the arrow keys to select the desired parameter.
  5. To confirm your selection, press MENU to save and return to the main menu. To cancel changes, press SOS or PTT.
  6. To exit the menu at any time, press SOS or PTT.

Scanning

The radio has a built-in scanner. To enable, press and hold the LAMP key for about two seconds. Press LAMP key momentarily to stop scanning.

Scanning Modes

The scanner can operate in three modes: Time, Carrier, or Search.

  • Time Operation (TO): Scanner stops on a signal, then resumes scanning after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes scanning after a preset time with no signal.
  • Search Operation (SE): Scanner stops on a signal. To resume scanning, press and hold the LAMP key.

Setting Scanner Mode

  1. Press MENU to enter the menu.
  2. Navigate to the scanner mode setting.
  3. Press MENU to select.
  4. Use arrow keys to select the desired scanning mode.
  5. Press MENU to save and confirm.
  6. Press SOS or PTT to exit.

Countdown Timer

A countdown feature is available with various selections. Access it via Menu item NO.6 ALARM.

Selective Calling

The BF-T20 features three different ways of group calling to minimize unwanted transmissions on busy channels.

  • Group Calling: One-to-many communication where all radios in a group are configured the same way.
  • Individual Calling (Paging): One-to-one communication where each radio has a unique ID code. Contact is made by sending a matching code.

CTCSS / DCS

These tones provide a method to filter out unwanted incoming transmissions. They do not prevent others from listening to your transmissions. CTCSS/DCS can only be changed via programming software.

1750Hz Tone-burst

To send a 1750Hz Tone-burst, press the MONI/VOL key while holding down the PTT. This feature does not require further configuration. If keypad lock is enabled, you can still send a 1750Hz tone.

Repeaters

A repeater is an automated transceiver that relays signals to extend communication range. The BF-T20 can activate relay functions.

How to Activate the Relay Function

  1. Press MENU to enter the menu.
  2. Navigate to NO.9 RELAYM.
  3. Press MENU to select.
  4. Use arrow keys to select the desired setting.
  5. Press MENU to save and confirm.
  6. Press SOS or PTT to exit.

Note: The RX and TX frequencies can only be programmed by software. For better encoding with CTCSS or DCS, the squelch level should be 5.

Programming

Memory channels allow you to store commonly used frequencies for easy retrieval. The BF-T20 has 20 memory channels, each storing receive/transmit frequencies, transmit power, group signaling, and bandwidth.

Computer Programming

The radio kit does not include a programming cable. To obtain a data cable and software, please contact your dealer.

5. Maintenance

Charging and Battery Maintenance

The battery should be fully charged before initial use. Optimal battery efficiency is achieved after three full charge and discharge cycles. When the battery level indicator shows empty, the radio will beep periodically, indicating it needs charging.

Charging Procedure

Illustration of Baofeng BF-T20 being charged via USB cable connected to a wall adapter.

Image: The Baofeng BF-T20 connected to a USB charger for fast charging.

  1. Connect the charging USB cable with the AC adapter and the socket of the radio.
  2. Plug the AC connector of the power adapter into a main AC wall outlet.
  3. When the battery level indicator shows charging, the charge is starting.
  4. When the battery level indicator shows full, the charge is finished. Pull out the USB charging cable.

Important: The radio should be turned off during the charge cycle.

Battery Maintenance Tips

  • The battery is not fully charged from the factory; charge it for at least three to five hours before first use.
  • Use only batteries approved by the original manufacturer.
  • Never attempt to disassemble the battery pack.
  • Do not expose the battery to fire or intense heat.
  • Dispose of batteries in accordance with local recycling regulations.

6. Troubleshooting

Appendix A: Troubleshooting Guide

SymptomPossible CauseSolution
The radio doesn't start.The battery is too low. The battery isn't correctly installed.Change or recharge the battery. Remove the battery and reinstall it.
The battery dies quickly.The battery is dead. The battery isn't fully charged.Purchase a new battery. Recharge the battery.
The LED indicates reception, but the speaker is silent.Volume is too low. CTCSS or DCS enabled.Turn up the volume. Change the CTCSS or DCS to match those you are trying to communicate. Turn off your CTCSS or DCS.
Others can't hear your transmission.Their CTCSS or DCS settings don't match yours. You are too far apart.Change your CTCSS or DCS settings to match your peers. Move in closer.

7. Specifications

Appendix C: General Specifications

Image showing the dimensions of the Baofeng BF-T20 walkie talkie with a ruler for scale.

Image: Dimensions of the Baofeng BF-T20, approximately 13.5cm in height.

ParameterValue
Frequency Range400.00-470.00 MHz
Storage Channel16
Step Frequency12.5/25KHz
Rated VoltageDC 3.7V
Frequency Stability±2.5ppm
Work Temperature-20 °C to +60 °C
Battery CapacityLi-ion 1500mAh
Battery LifeAbout 12 Hours
Antenna Impedance50 Ω
Dimensions21*54*135mm (Including Antenna)
Weight110g (Including battery)

Transmitter Specifications

ParameterValue
Output Power0.5W/1W (Note: Product description states 5W, refer to product packaging for exact power)
Modulation Mode (W/N Band)16KF3E/11KF3E
Maximum Frequency Deviation (W/N Band)<5KHz / ≤2.5KHz
Spurious Power<7.5 μW
Adjacent Channel Power<-65dB/≤-60dB
Audio Distortion<5%
SNR≥-45dB/≥-40dB
CTCSS/DCS Frequency Deviation (W/N Band)0.7±0.1KHz (W), 0.4±0.1KHz (N)
Modulation Sensitivity8-12mV
Transmitting Current<1000mA

Receiver Specifications

ParameterValue
Sensitivity<0.25 μV (12dB SINAD)
Audio Power1W
Intermodulation Interference Resistance≥65dB (W), ≥60dB (N)
Adjacent Channel Selectivity (W/N Band)≥65dB (W), ≥55dB (N)
Audio Distortion5%
Receiving Current≤380mA

8. User Tips

  • Hands-Free Operation (VOX): Utilize the VOX function for hands-free communication, especially useful during activities like cycling, carrying objects, or working.
  • Convenient USB Charging: The radio features a Mini USB port (note: not Micro USB) for charging. You can recharge it using a car charger, power bank, PC, USB desktop charger, or wall charger. The red light indicates charging, and the green light indicates charging is complete.
  • Understanding Range: The maximum range for this walkie talkie is typically 3km-5km. Actual range can vary significantly based on terrain, obstacles, and environmental conditions. For optimal performance, try to maintain line-of-sight and avoid dense obstructions.
  • Camo Model Variation: Be aware that standard BF-T20 and upgraded BF-T20D camouflage models may be shipped randomly.
  • Charger Port Variation: The charger ports (Micro USB or USB-C) are shipped randomly.

9. Support

For further assistance, including obtaining a programming cable and software, please contact your dealer. A detailed user manual in PDF format is also available for download: User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.