Reilyn P625

Contents

REILYN P625 Mini Staples User Manual

For use with P625 Pneumatic Nail Guns

1. Introduction

This manual provides essential information for the safe and effective use of REILYN P625 23GA Mini Staples. These staples are designed for use with compatible P625 pneumatic nail guns in various applications such as wooden frame, floor, and carpet fixing. Please read this manual thoroughly before using the product to ensure safety and optimal performance.

Box of REILYN P625 Mini Staples

Figure 1: REILYN P625 Mini Staples in packaging

2. Safety Information

WARNING: BEFORE USING THE NAILS WITH A PNEUMATIC TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR SERIOUS INJURY.

  • Wear Safety Glasses or Goggles: Always wear safety glasses or goggles when operating a pneumatic tool with these fasteners. This protects against dust, exhausted air, or fasteners flying up due to improper handling.
  • Ear Protection May Be Required: In environments with high noise levels from pneumatic tools, ensure appropriate hearing protection is worn by the operator and others in the work area to prevent hearing damage.
  • Use Only with Air Compressor: These nails are designed for use with pneumatic tools powered by compressed air. Never use with other high-pressure gases or combustible gases (e.g., Oxygen, acetylene) as this poses an explosion risk.
  • Operate Within Proper Air Pressure Range: Ensure your pneumatic tool operates within the recommended air pressure range (typically 70 psi to 100 psi, or 5 to 7 bar). Do not exceed 120 psi (8.3 bar) as this can damage the tool and cause unsafe operation.
  • Do Not Operate Near Flammable Substances: Never use pneumatic tools or fasteners near flammable substances (e.g., thinner, gasoline). Volatile fumes can be drawn into the compressor, compressed, and result in an explosion.
  • Use Correct Fittings: Ensure the connector on your pneumatic tool does not hold pressure when the air supply is disconnected. Incorrect fittings can leave the tool charged with air, allowing it to fire fasteners unexpectedly and cause injury.
  • Disconnect Air Supply and Empty Magazine When Not in Use: Always disconnect the air supply from the tool and empty the magazine of fasteners when operation is complete, suspended, unattended, moving to a different work area, adjusting, disassembling, repairing, or clearing a jammed fastener.
  • Inspect Tool Screw Tightness: Regularly check that all screws and bolts on your pneumatic tool are tight and properly installed to prevent accidents and tool damage.
  • Do Not Touch Trigger Unless Intending to Drive: With the air supply connected, never touch the trigger unless you intend to drive a fastener. Avoid walking around with the tool with the trigger pulled.
  • Never Point Discharge Outlet Toward Yourself and Personnel: Always ensure the tool's discharge outlet is not pointed at people during connection, disconnection, loading, or operation to prevent serious accidents from misfires.
  • Use Specified Fasteners: Only use fasteners specified for your tool, such as these P625 nails for P625 pneumatic nail guns, to prevent malfunction.
  • Place Discharge Outlet Properly: Failure to properly place the tool's discharge outlet against the work surface can cause fasteners to fly up, which is extremely dangerous.
  • Keep Hands and Body Away from Discharge Outlet: When loading and using the tool, never place hands or any body part in the fastener discharge area to avoid accidental injury.
  • Avoid Driving Fasteners Close to Edges/Corners or Thin Material: Driving fasteners too close to edges, corners, or into thin material can cause the workpiece to split and the fastener to fly off, potentially hitting someone.
  • Do Not Drive Fasteners on Top of Other Fasteners: This can cause fasteners to deflect and lead to injury.
  • Remove Fasteners After Operation: If fasteners remain in the magazine after use, there is a risk of accidental firing if the tool is handled carelessly or reconnected to air. Always remove fasteners from the magazine after completing operation.
  • Check Contact Trip Mechanism: If using a contact trip type tool, frequently check that the mechanism is working correctly. Do not use the tool if it malfunctions, as this can lead to accidental firing.
  • Using Tool in Elevated Places: When fastening on roofs or slanted surfaces, start from the lower part and work upwards. Secure the air hose close to the work area to prevent accidental pulling or snagging.
  • Tool Control Integrity: Never use the tool if any portion of its controls (e.g., trigger, contact arm) is inoperable, disconnected, altered, or not working properly.
  • Never Actuate Tool into Free Space: This prevents hazards from free-flying fasteners and excessive strain on the tool.
  • Always Assume Tool Contains Fasteners: Treat the tool as if it always contains fasteners, even if you believe it is empty.
  • Do Not Use on Scaffoldings/Ladders for Specific Applications: The tool should not be used for applications that involve changing driving locations using scaffoldings, stairs, or ladders, or for fitting transportation safety systems.

3. Product Specifications

AttributeSpecification
BrandReilyn
Model NumberP625
TypeMini Staples (23GA)
MaterialMetal alloy
Shank Width0.65mm
Lengths Available10mm, 12mm, 15mm, 20mm, 25mm
ColorCopper red (coating for anti-oxidation/corrosion)
Package Quantity10000 pcs/box
UseHome DIY (e.g., wooden frame, floor, carpet fixing)
Dimension diagram of P625 nails

Figure 2: Nail dimensions (0.65mm width, various lengths)

Strips of P625 Mini Staples

Figure 3: Individual strips of REILYN P625 Mini Staples

4. Setup and Loading

These instructions pertain to loading the REILYN P625 Mini Staples into a compatible P625 pneumatic nail gun. Always refer to your specific nail gun's manual for detailed setup and safety procedures.

4.1 Nail Loading Procedure

  1. Disconnect Air Hose: Before loading any fasteners, always disconnect the air supply hose from the pneumatic nail gun.
  2. Open Magazine: Press the LATCH (part number 200070) to open the DOOR (part number 210050), then open the MAGAZINE COVER (part number 420190).
  3. Adjust Nail Support: Adjust the height of the NAIL SUPPORT (part number 420210) according to the length of the nails you are loading.
  4. Load Nails: Fix the first nail strip in the groove on the FEED PAWL (part number 210080). Ensure the nails are correctly oriented.
  5. Close Magazine: Close the MAGAZINE COVER (part number 420190), then close the DOOR (part number 210050).
  6. Reconnect Air Hose: Once the nails are securely loaded and the magazine is closed, you may reconnect the air supply hose.

Video 1: Demonstration of P625 Air Stapler Nail and its various sizes.

Pneumatic nail gun with loaded staples

Figure 4: P625 Pneumatic Nail Gun ready for operation with REILYN Mini Staples

5. Operating Instructions

After loading the nails and reconnecting the air supply, perform a test operation to ensure the tool and fasteners are working correctly.

5.1 Test Operation

  1. Adjust the air pressure to approximately 70 psi (5 bar) and connect the air supply.
  2. Without touching the trigger, depress the contact arm against a workpiece. Pull the trigger. The tool should fire a fastener.
  3. With the tool off the workpiece, pull the trigger. Then depress the contact arm against the workpiece. The tool should fire a fastener.
  4. Adjust the air pressure as needed to the lowest possible setting that effectively drives the fastener, considering the diameter and length of the fastener and the hardness of the workpiece.

Important: Keep hands and body away from the discharge outlet when driving fasteners to prevent injury.

6. Maintenance and Inspection (for Nail Gun and Staples)

Proper maintenance of your pneumatic nail gun and careful handling of staples will ensure longevity and safe operation. It is recommended that servicing and repairs be performed by a professional technician.

6.1 General Maintenance

  • Disconnect Air Hose and Remove Nails: Always disconnect the air hose and remove all nails from the nail gun before performing any maintenance, inspection, or clearing a jam.
  • Inspect Magazine: Clean the magazine regularly to remove dust or debris. Lubricate the nailer rail with appropriate nailer lubricant.
  • Periodic Checks:
    • Check the piston bumper for normal operation; a damaged bumper can cause damage to other components.
    • Inspect O-rings for wear or damage, as this can affect overall performance.
    • Ensure all screws on the tool are secure.
    • When repairing, ensure internal parts are clean and lubricated.

6.2 Clearing a Jammed Nail

If a nail becomes jammed in the tool, follow these steps:

  1. Disconnect Air Hose: Immediately disconnect the air supply hose.
  2. Remove All Nails: Carefully remove any remaining nail strips from the magazine.
  3. Clear Jam: Use a slotted head screwdriver to carefully remove the jammed nail.
  4. Professional Service: If jams occur frequently, contact an authorized service center for inspection and repair.

6.3 Storage

  • For extended periods of non-use, apply a thin coat of lubricant to the steel parts of the nail gun to prevent rust.
  • Store the nail gun and staples in a warm, dry place. Avoid storing in cold weather environments.

7. Troubleshooting

This section addresses common issues related to the use of REILYN P625 Mini Staples with a pneumatic nail gun.

  • Nails not feeding properly: Ensure the nail strips are correctly loaded into the magazine and the nail support is adjusted for the correct nail length. Check for any debris in the magazine.
  • Nails jamming frequently: Follow the 'Clearing a Jammed Nail' procedure. If jams persist, the nail gun may require professional servicing or inspection for worn parts.
  • Inconsistent nail depth: Adjust the air pressure within the recommended range (70-100 psi) to match the nail length and the hardness of the material. Ensure the tool's depth adjustment (if available) is correctly set.
  • Tool not firing: Check that the air supply is connected and at the correct pressure. Ensure the contact trip mechanism is fully depressed against the workpiece and the trigger is pulled. If the tool's controls are altered or inoperable, do not use it.

8. User Tips

No specific user tips based on reviews or Q&A are available at this time.

9. Warranty and Support

For detailed item guides and documents, including a user manual in PDF format, please refer to the official documentation provided by the seller. This manual focuses on the safe use of the staples themselves and general operational context for the compatible tool.

A user manual (PDF) is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.